1995 LAND ROVER DISCOVERY air condition

BRAKES
13
REPAIR FRONT BRAKE CALIPERS
Service repair no - 70.55.03
Service repair no - 70.55.16
Service tool:
LRT-70-500 - Piston clamp
Before starting repair refer to general brake service
practice.
See General Brake Service Practice
Remove caliper
1.Loosen front wheel retaining nuts, raise front of
vehicle, lower onto axle stands, remove wheels.
2.Expose flexible brake hose by moving coiled
protective covering.
3.Using a recognised hose clamp, clamp hose to
prevent loss of brake fluid.
4.Disconnect rigid brake pipe from flexible hose,
seal exposed ends to prevent ingress of dirt.
5.Remove split [cotter] pin, retaining pins and
springs, withdraw pads. If refitting pads, identify
them for assembly to original locations.
6.Loosen bolts and remove caliper.
Repair
Do not separate caliper halves
7.Clean outer surfaces of caliper using aerosol
brake cleaner.
8.Using special tool LRT-70-500, clamp pistons in
inboard half of caliper. Gently, keeping fingers
clear, and withCAUTION,apply air pressure to
fluid inlet port to expel pistons. It is unlikely that
pistons will expel at same time, regulate rate
with a suitable piece of wood between
appropriate piston and caliper.
9.Finally remove pistons, identifying them with
their respective bores.
10.Remove wiper seal retainer by inserting a blunt
screwdriver between retainer and seal. Pry
retainer carefully from mouth of bore.
11.Taking care not to damage seal grooves, extract
wiper seal and fluid seal.
12.Clean bores, pistons and seal grooves using
clean brake fluid only. If caliper or pistons are
corroded, or their condition is not perfect, new
parts must be fitted.

BRAKES
15
REPAIR REAR BRAKE CALIPERS
Service repair no - 70.55.06
Service repair no - 70.55.17
Service tool:
LRT-50-700 - Piston clamp
Before starting repair refer to general brake service
practice.
See General Brake Service Practice
Remove caliper
1.Loosen rear road wheel nuts. Jack up vehicle,
lower onto axle stands, remove wheels.
2.Using a recognised hose clamp, clamp flexible
brake hose above rear axle.
3.Remove brake pipe(s) from rear brake caliper(s).
4.Seal pipe ends to prevent ingress of dirt.
5.Remove retaining pins and springs and withdraw
pads. If same pads are to be refitted, identify
them for assembly in original positions.
6.Remove two bolts, withdraw caliper from axle.
Repair
Do not separate caliper halves
7.Clean outer surfaces of caliper with aerosol
brake cleaner.
8. WITH CAUTIONexpel pistons from their bores
by applying air pressure to fluid inlet port. It is
unlikely both pistons will expel at same time,
regulate rate with a suitable piece of wood
inserted between two pistons.
9.Finally, remove pistons keeping them identified
with their respective bores.
10.Remove wiper seal retainer by inserting a blunt
screwdriver between retainer and seal and pry
retainer carefully from mouth of bore.
11.Taking care not to damage seal grooves, extract
wiper seal and fluid seal.
12.Clean bores, pistons and particularly seal
grooves using clean brake fluid only. If caliper or
pistons are corroded or their condition is not
perfect new parts must be fitted.

74WHEELS AND TYRES
2
FAULT DIAGNOSIS FAULT - SYMPTOMS
Vibration through steering wheel
1.Check tyre pressures.
See Repair, Tyre
Pressures
2.Check condition of tyres.See Tyre Wear Chart
3.Check front wheel alignment.See STEERING,
Adjustment, Front Wheel Alignment
4.Check wheel balance.See Repair, Wheel
Balancing
NOTE: In the event that any apparent
vibration is not eliminated at this stage.
See PROPELLER SHAFTS, Fault
diagnosis, Vibration Harshness
NOTE: In the event that any apparent
vibration is not eliminated at this stage, go
to steering Fault Diagnosis, Fault -
Symptom (Steering vibration, road wheel
shimmy/wobble).
See STEERING, Fault diagnosis,
Steering Faults
NOTE: Radial ply tyres have a flexible
sidewall, which produces a sidewall bulge
making the tyre appear under-inflated.
This is a normal condition for radial ply tyres. Do
not attempt to reduce this bulge by over-inflating
the tyre.
1. Correct inflation.
2. Under-inflation.
3. Over-inflation.
4. Tread contact with road.

WHEELS AND TYRES
1
REPAIR GENERAL INFORMATION
WARNING: This is a multi- purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures.
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels.The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim.
See
Tyre Fitting
WARNING: Do not fit an inner tube to an
alloy wheel.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment.
See Fault
diagnosis, Tyre Wear Chart
if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration below.
When the tread has worn to a remaining depth of 1.6
mm the indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration below.

74WHEELS AND TYRES
2
REPAIR When the indicators appear in two or more adjacent
grooves, at three locations around the tyre, a new tyre
must be fitted.
NOTE: Do not attempt to interchange
tyres, e.g. from front to rear, as tyre wear
produces characteristic patterns
depending on their position. If tyre position is
changed after wear has occured, the performance
of the tyre will be adversely affected.
NOTE: Territorial vehicle regulations
governing tyre wear MUST be adhered to.
WHEELS INSPECTION
Regularly check the condition of the wheels. Replace
any wheel that is bent, cracked, dented or has
excessive runout.
VALVES INSPECTION
Check condition of inflation valve. Replace any valve
that is worn, cracked, loose, or leaking air.TYRE PRESSURES
Maximum tyre life and performance will be
obtained only if tyres are maintained at the correct
pressures.
Tyre pressures must be checked at least once a
month and at least once a week, preferably daily, if
the vehicle is used off road.
The tyre inflation pressure is calculated to give the
vehicle satisfactory ride and steering characteristics
without compromising tyre tread life. For
recommended tyre pressures in all conditions.
See
GENERAL SPECIFICATION DATA, Information,
Wheels and Tyres
American vehicles - A label attached to the inside
edge of the driver's door also provides tyre pressure
information.
Always check tyre inflation pressures using an
accurate gauge and inflate tyres to the
recommended pressures only.
Check and adjust tyre pressuresONLYwhen the
tyres are cold, vehicle parked for three hours or more,
or driven for less than 3.2 km (2 miles) at speeds
below 64 km/h (40 mph). Do not reduce inflation
pressures if the tyres are hot or the vehicle has been
driven for more than 3.2 km (2 miles) at speeds over
64 km/h (40 mph), as pressures can increase by 0.41
bars (6 p.s.i) over cold inflation pressures.
CheckALLtyre pressures including the spare. Refit
the valve caps as they form a positive seal and keep
dust out of the valve.

74WHEELS AND TYRES
4
REPAIR Static balance
Wheel tramp
A. Heavy spot.
B. Add balance weights here.
C. Centre line of spindle.
Static balance is the equal distribution of weight
around the wheel. A statically unbalanced wheel will
cause a bouncing action called wheel tramp. This
condition will eventually cause uneven tyre wear.Dynamic balance
Wheel shimmyA. Heavy spot.
B. Add balance weights here.
C. Centre line of spindle.
Dynamic balance is the equal distribution of weight on
each side of the centre line so that when the wheel
spins there is no tendency for side to side movement.
A dynamically unbalanced wheel will cause wheel
shimmy.

75SUPPLEMENTARY RESTRAINT SYSTEM
14
REPAIR AIRBAG HARNESS
Service repair no - 86.70.63
Remove
1.Remove driver's airbag.
See driver's airbag
module.
2.Remove passenger's airbag.See passenger's
airbag module.
3.Remove dash panel assembly.See CHASSIS
AND BODY, Repair, dash panel assembly
4.Remove heater blower unit.See HEATING
AND VENTILATION, Repair, blower motor
unit - heater and air conditioning.
5.Remove heater and cooler unit.See AIR
CONDITIONING, Repair, heater and cooler
unit
Pre 97 MY
6.Remove 3 screws securing expansion tank and
position expansion tank aside.
7.Disconnect multiplug from each crash sensor.
8.Release airbag harness from clips and ties along
the bulkhead and each valance.
9.Displace airbag harness grommet to inside of
bulkhead and feed harness through bulkhead.
All Models
10.Disconnect multiplug from airbag control unit.
11.Release airbag harness from under carpet.
12.Release ties securing harness along toeboard.
13.Disconnect steering wheel airbag multiplug.
14.Release airbag harness from driver's side and
remove.
Refit
15.Reverse removal procedure.
CAUTION: Ensure harness is correctly
routed in harness protector and that all
securing clips and ties are correctly
engaged and harness is undamaged. Ensure all
connections are fully engaged and retained by
their latches.

CHASSIS AND BODY
51
REPAIR 16.Cut through sealer between the supports.
If heated front screen: Cut through the 2 wires
each side of the supports. Tape cut wires and
panels to prevent damage to bodywork when
screen is removed.
17.Attach suction cups to glass and lift glass from
body flange, cut sealer free around supports as
necessary.
WARNING: If glass has splintered: Protect
eyes and operate demister blower at
maximum speed to remove any glass from
ducts. Use a vacuum cleaner to remove glass
particles from inside the vehicle.
Refit
18.Check condition of supports, renew if necessary.
Locating studs must be at right angle to flange.
NOTE: The supports were fitted to early
vehicles and now replaced with nylon
sheaths.
19.Carefully cut back old sealant around body
flange to obtain a smooth surface 2mm (1/10in)
thick.DO NOT cut down to flange.
20. If refitting original glass:It must be free from
chips or cracks. Cut back old sealant around
glass to obtain a smooth surface 2mm (1/10 in)
thick.DO NOT cut down to glass surface.
CAUTION: Lay glass on felt covered
supports, do not stand on edge. Any
chipping of glass edge may develop into
cracks.
21.Align header finisher on top edge of glass, push
flange fully onto glass and use a wooden block
and mallet to ensure fit.
22.Carefully align each side finisher on edge of
glass, push flange fully onto glass and use a
wooden block and mallet to ensure fit.
23.Using a cotton bud, apply glass cleaning solvent
(yellow cap) to inside face of glass, 20mm (13/16
in) strip around inside of finishers and 30mm (1
1/8 in) wide along bottom edge. Immediately
wipe off solvent with a clean cloth.
CAUTION: Do not touch cleaned or primed
surfaces with fingers.