1995 LAND ROVER DISCOVERY air condition

Tdi
1
REPAIR VISCOUS COUPLING, FAN BLADES, PULLEY AND
FAN COWL
Service repair no - 26.25.03/05
Viscous coupling -Remove1to3
Fan blades -Remove1to4
Fan cowl -Remove1to3
Fan pulley -Remove1to6
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing or adjusting drive belt.
1.Slacken nut securing viscous coupling/fan blade
assembly to pulley.
NOTE: Nut securing viscous unit to pulley
has a left hand thread. Release by turning
clockwise when viewed from front of
viscous unit.
2.Drop viscous unit and fan assembly into bottom
of cowling
3.Remove two fixings clips from top of cowling and
lift cowling complete with viscous unit and fan
out of lower mountings.
4.Remove fan blades from viscous coupling if
necessary.
5.Remove serpentine drive belt and, if fitted, air
conditioning compressor belt.
6.Remove pulley fixings, remove pulley.
NOTE: The serpentine belt is removed by
using a hexagonal socket and tommy bar
on the auto-tensioning pulley nut. Whilst
tensioning the device the belt can be removed.
7.Reverse removal procedure. Ensure fan blades
are fitted correctly. Fan is marked 'front' and
should be fitted with word 'front' closest to
radiator. Tighten to
30 Nm.
8.Refit drive belt.See ENGINE, Repair, Drive
Belt
THERMOSTAT
Service repair no - 26.45.01
Remove
1.Partially drain cooling system, until coolant level
is below thermostat housing.
2.Disconnect hose from thermostat housing.
3.Disconnect electrical connections to water
temperature switch.
4.Remove outlet elbow.
5.Withdraw thermostat.
Test
6.Note rating of thermostat is 88°C. Place
thermostat in a container half full of water. Heat
water, observe temperature at which thermostat
begins to open. Thermostat is satisfactory if its
open between 85°C and 89°C.
Refit
7.Insert thermostat with jiggle pin/vent hole upper
most (12 o'clock position) .
8.Fit the outlet elbow and new joint washer.
Tighten to
28 Nm.
9.Reverse removal procedure. 1 to 3.
10.Check for coolant leaks around all connections
and joint faces.

26COOLING SYSTEM
2
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing drive belts.
1.Drain engine cooling system.
See Adjustment,
Coolant
2.Remove top hose radiator to thermostat.
3.Remove top hose intercooler to induction
manifold.
4.Slacken water pump and power steering pump
pully retaining bolts.
5.Remove drive belt.
6.Remove centre nut from belt tensioner.
7.Manoeuvre pulley upwards and withdraw
tensioner from retaining stud.
8.Disconnect hose thermostat to bottom hose,
release hose from clip on water pump and move
aside.
9.Remove water pump pulley.
10.Remove power steering pump pulley.
11.Remove 8 bolts securing water pump, noting
location of 3 through bolts.
12.Withdraw pump and gasket, clean all gasket
material from mating surfaces.
Refit
13.Refit water pump in reverse order to removal
using new gasket.RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Disconnect radiator top hose.
3.Remove fan blade assembly.
4.Remove cowl.
5.Disconnect engine oil cooler connections and
turbo intercooler connections from radiator ends.
NOTE: Oil spillage will occur when
connections are loosened. Blank off
exposed oil connections.
6.Disconnect expansion tank bleed hose from
radiator.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.
Refit
9.Check radiator sealing strips are securely
located.
10.Transfer oil cooler adaptors if fitting new radiator.
11.Reverse removal procedure. Tighten oil cooler
connections to
30 Nmbefore fitting fan blades
and cowl.
12.Check all connections for leaks.

V8i
1
FAULT DIAGNOSIS ENGINE OVERHEATING
Before conducting any cooling system diagnosis:
See
Description and operation, Engine Cooling
1.Is coolant level correct?
NO - Allow engine to cool, top up level to
expansion tank seam.
YES - Continue.
2.Is drive belt tension correct?
NO -
See ENGINE, Repair, Drive Belt -
Check Tension
YES - Continue.
3.Is ignition timing correct?
NO -
See ELECTRICAL, Adjustment,
Ignition Timing
YES - Continue.
4.Is coolant in radiator frozen?
YES - Slowly thaw and drain system.
See
Adjustment, Coolant Requirements
NO - Continue.
5.Is air flow through radiator restricted or blocked?
YES - Apply air pressure from engine side of
radiator to clear obstruction.
NO - Continue.
6.Are there any external leaks, from water pump,
engine gaskets or the heater unit?
YES - Investigate and rectify.
See Adjustment,
Coolant Requirements
NO - Continue.
7.Are fan blades fitted correct way round, concave
side towards engine?
NO - Rectify.
YES - Continue.8.Is viscous unit operating correctly?
See
Description and operation, Viscous Fan
NO - Renew.See Repair, Viscous
Coupling, Fan Blades, Pulley and Fan
Cowl
YES - Carry out a pressure test on radiator cap
and system. Check thermostat type,
operation and correct fitting
See Repair,
Thermostat
If pressure test leads you to suspect coolant
leakage across gaskets, go to check 11,
otherwise: Continue.
9.Are the air conditioning fans operating correctly?
See Electrical Trouble Shooting Manual.K5
NO - Rectify.
YES - Continue.
10.Is temperature sender and gauge giving
accurate readings?
NO - Substitute parts and compare readings.
YES - Continue.
11.Carry out cylinder pressure test to determine if
pressure is leaking into cooling system causing
over pressurising and loss of coolant.
If problem is not diagnosed, check the coolant system
for engine oil contamination and engine lubrication
system for coolant contamination.
If the coolant only, or both systems are contaminated,
suspect cylinder head gaskets or radiator.
If only the lubrication stystem is contaminated with
coolant, suspect inlet manifold or front cover gaskets.

26COOLING SYSTEM
2
FAULT DIAGNOSIS ENGINE RUNS COLD
Before conducting any cooling system diagnosis:
See
Description and operation, Engine cooling
1.Check operation of viscous unit.See
Description and operation, Viscous Fan
Is viscous unit operating correctly?
NO -
See Repair, Viscous coupling, fan
blades, pulley and fan cowl
YES - Continue.
2.Is thermostat correct type and operating?
See
Repair, Thermostat
If problem is not diagnosed: Continue.
3.Are the air conditioning fans operating
continuously?
YES -
See Electrical Trouble Shooting
Manual.
NO - Continue.
4.Is temperature sender and gauge giving
accurate readings? Substitute parts and
compare readings. If problem is not diagnosed
repeat tests, starting at 1.

26COOLING SYSTEM
4
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Remove viscous coupling and fan assembly.
See Viscous Coupling, Fan Blades, Pulley
and Fan Cowl
3.Release 2 clips and remove fan cowl.
4.Disconnect radiator top hoses.
5.Disconnect four transmission and engine oil
cooler connections to radiator end tanks. Note oil
spillage will occur when connections are
loosened. Blank off exposed oil connections.
6.Disconnect transmission oil temperature sensor.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.Refit
9.Reverse removal procedure.
10.Clean unions and apply sealant.
11.Lubricate new 'O' rings before fitting.
12.Check radiator sealing strips are securely
located.
13.Transfer oil cooler adaptors if fitting new radiator.
14.Ensure that oil cooler connections are tightened
to
30 Nm.before fitting fan blades and cowl.
15.Clean coolant/oil spillage from vehicle.
16.Check all connections for coolant/oil leaks.

Mpi
3
REPAIR
12.With assistance lift out radiator assembly.
Do not carry out further dismantling if component
is removed for access only.
13.Remove 2 bolts securing radiator rail to radiator.
14.Remove radiator rail.
15.Remove 8 nuts securing fan assemblies to
radiator.
NOTE: Vehicles without air conditioning
have one cooling fan fitted.
Refit
16.Position fan assemblies to radiator and tighten
nuts to
6Nm
17.Position radiator rail to radiator and secure with
bolts.
18.Position radiator to vehicle.
19.Secure radiator to body with the side support
brackets and retaining bolts.
20.Connect multiplugs to cooling fans.
21.Fit and secure 6 hoses to radiator.
22.Secure air cleaner to throttle housing to
brackets.
23.Refill cooling system.
24.Reconnect battery negative lead.

33CLUTCH
2
FAULT DIAGNOSIS FAULT/SYMPTOM CHART
Symptoms
Slip Spin/Drag Judder/Fierce Fault Item
* * * Worn or oil on clutch linings 2
* * * Mechanical damage45678
* * Distorted clutch plate 2
* Failed or air in hydraulic system 12 13
* * Primary shaft tight fit in crankshaft bush 15 17
* Clutch splines sticking 2 15
* Weak clutch plate springs or insecure/worn
engine/gearbox mountings6
* Insecure/worn propeller shafts
* Insecure/worn suspension components/rubber
bushes
For items refered to in this chart.See Description and operation, Description
CLUTCH NOISE - MECHANICAL FAULTS
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox input/primary shaft bearings.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed
Noise from clutch or gearbox in neutral, which
changes tone or becomes worse when the clutch
is depressed.
Suspect worn release bearing.
Knocking/rattling from clutch or gearbox in
neutral, which is reduced or disappears when the
clutch is depressed.
Suspect worn/weak release lever retainer or
clutch unit.
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox fault.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed.HYDRAULIC FAULTS
Unable to dis-engage clutch, little or no pedal
resistance.
1.Check condition, specification and level of fluid.
2.Check pipes and cylinders for leaks.
3.Check that air vent in reservoir lid is clear.
Suspect faulty master cylinder if no fluid leaks
present.
See Repair, Master Cylinder
Spongy pedal operation
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect air in fluid.
See Repair, Bleed Hydraulic System
Clutch is difficult to dis-engage and/or does not
immediately re-engage when pedal is released.
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect pedal pivot, master cylinder or slave
cylinder seizure.
See Repair, Master Cylinder

41TRANSFER GEARBOX
2
FAULT DIAGNOSIS PROCEDURE
Prior to road test
1.Check oil level in transfer box is correct.
2.Check tightness of level and drain plugs.
3.Check breather system for blockage. To validate
the system the pipe must be removed,
inspected, rectified as necessary and refitted.
4.Remove all traces of oil from exterior of transfer
box.
Take vehicle for short road test.
5.Identify source of leaks and rectify as follows.
Front or rear output seal leaking:-
1.Drain the oil and remove the leaking output
flange.
2.Inspect the seal track on the flange for surface
damage. If damaged renew component.
3.Remove and discard the oil seal.
4.Inspect the seal locating bore and remove any
sharp edges which may damage the new oil
seal.
5.Fit new seal.
6.Fit the output flange and all the other parts.
7.Add oil to correct level into the gearbox.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Cover plate gasket leaking.
1.Drain the oil and remove the leaking cover plate.
2.Remove all traces of joint sealant from both joint
faces.
3.Degrease all components and apply a thin film of
Hylomar sealant, to both joint faces.
4.Apply thread sealant to the bolts which come
into contact with gearbox oil.
5.Refit cover plate.
CAUTION: Care must be taken not to
overtighten the fixings.Leak between the main and transfer gearboxes.
1.Site vehicle onto a ramp [hoist].
2.Select neutral in transfer box and select 4th gear
in the main gearbox.
3.Run engine at 2000 rpm with the clutch/drive
engaged.
4.Observe joint between the main and transfer
boxes.
5.If oil leak is found establish if it is gear oil.
6.If so, the leak is originating from the transfer box.
7.Check the two inner (main/transfer) bolts are oil
tight, as these holes are tapped through into the
main transfer case.
8.Remove the transfer box to inspect the
mainshaft collar seal track condition, and the
front face of the transfer case for porosity.
See
Repair, LT230T Transfer Gearbox
9.If these areas require servicing, the transfer
gearbox input seal must also be renewed.
CAUTION: Avoid damaging the new seal
lip and ensure the seal is fitted flush with
the machined face. Also ensure the new
seal is not damaged when refitting the transfer
gearbox.
10.If red A.T.F type oil is seen leaking during the
workshop test, investigate the main gearbox for
cause of leak.
Detent plug or electrical switch leaks.
1.Detent plugs and electrical switches do not
usually leak. It must be noted that they fit into
open tapped holes in the transfer case and
therefore should be considered when looking for
the source of the leak.