1995 JEEP YJ transmission shifter

(8) Remove shift handle by pulling upward sharply
on handle. Then remove shift bezel (Fig. 7).
(9) Remove console cover screws (Figs. 9 and 10).
(10) On models with power mirror switch, pry
switch out of console cover and disconnect switch
connector (Fig. 9).
(11) Remove cover from console (Fig. 10).
(12) Remove screws attaching console to brackets
and shifter covers (Fig. 11).
(13) Remove console (Fig. 11).
(14) Remove duct (Fig. 11).
(15) Disconnect wire at parking brake switch on le-
ver (Fig. 4).
(16) Remove lever and cable tensioner assembly
from floorpan.
(17) Move cover and boot aside for access to lever
arm (Fig. 4).
(18) Remove E-clip and pin that connect tensioner
to lever arm (Fig. 4).
(19) Parking brake switch can be replaced at this
time if necessary.
PARKING BRAKE LEVER INSTALLATION (XJ WITH
FULL CONSOLE)
(1) Assemble lever and tensioner (Figs. 4 and 5).
Be sure E-clip is fully engaged in retaining pin (Fig.
4).
(2) Verify that tensioner boot is fully seated in
cover (Fig. 6).
(3) Position assembled lever and tensioner in floor-
pan.(4) Install parking brake switch on lever if re-
moved, and connect brake warning light wires to
switch.
(5) Install duct and console (Fig. 11).
(6) Connect power mirror switch wire to switch
and install switch in console cover.
(7) Install console cover.
(8) On automatic transmission models, install shift
bezel and shift handle.
(9) On manual transmission models, install bezel,
outer boot, and shift knob.
(10) Raise vehicle.
(11) Insert tensioner rod in equalizer and install
adjusting nut on tensioner rod.
(12) Install nuts attaching lever support plate to
floorpan and lever.
(13) Adjust parking brakes. Refer to procedure in
this section.
(14) Lower vehicle and verify proper parking brake
operation.PARKING BRAKE LEVER REMOVAL (XJ WITHOUT
CONSOLE)
(1) Raise vehicle.
(2) Remove nuts attaching lever support plate to
underside of floorpan.
Fig. 9 Console Cover Screws And Power Mirror
Switch Connector
Fig. 10 Console Cover And Base
5 - 64 PARKING BRAKESJ

INSTALLATION
(1) Connect electrical connectors to ignition switch.
Make sure that switch locking tabs are fully seated
in wiring connectors.
(2) Before attaching ignition switch to a tilt steer-
ing column, the transmission shifter must be in Park
position. The park lock dowel pin and column lock
flag must also be properly indexed before installing
switch (Fig. 9).
(a) Place transmission shifter in PARK position.
(b) Place ignition switch in lock position. The
switch is in the lock position when column lock flag
is parallel to ignition switch terminals (Fig. 9).
(c) Position ignition switch park lock dowel pin
so it will engage steering column park lock slider
linkage (Fig. 10).(d) Apply a light coating of grease to column lock
flag and park lock dowel pin.
(3) Place ignition switch against lock housing open-
ing on steering column. Ensure that ignition switch
park lock dowel pin enters slot in park lock slider
linkage in steering column.
(4) Install retaining bracket and ignition switch
mounting screws. Tighten screws to 36.5 Nzm (2664
in. lbs.) torque.
(5) Install ignition lock cylinder:
Fig. 4 Key-In-Switch and Halo Lamp Connector
Fig. 5 Key Cylinder Retaining Screw
Fig. 6 Key Cylinder Retaining Screw
Fig. 7 Unseated Key Cylinder
JIGNITION SYSTEMS 8D - 27

(14) Remove the Interlock cable from the steering
column. Refer to Automatic Transmission Shifter/Ig-
nition Interlock in this group.
(15) Remove the column. Use care to avoid damag-
ing the paint or trim.
INSTALLATION
CAUTION: Bumping, jolting and hammering on the
steering column shaft and gear shift tube must be
avoided during all service procedures.
(1) With the front wheels in the straight ahead po-
sition. Align and install the column to coupler.Do
not apply force at the top of the steering col-
umn shaft.(2) Ensure the ground clip is on the left spacer slot
(Fig. 17).
(3) Install the Interlock cable from the steering col-
umn. Refer to Automatic Transmission Shifter/Igni-
tion Interlock in this group.
(4) Install wiring harness connections to steering
column (Fig. 16).Ensure the wiring is not pinched
and all connections are correctly locked in
place.
(5) Install wiring harness connector onto multi
function switch (Fig. 18). Torque multi function
switch wiring harness connector retaining bolt to 2
Nzm (17 in. lbs.).
(6) Install wiring harness connector for key light
switch connection, onto the ignition switch (Fig. 19).
Fig. 15 Multi Function Switch Wiring Connection
Fig. 16 Steering Column Wiring Harness
J9519-57
Fig. 14 Halo Light And Key In Buzzer Wiring
Connection
JSTEERING 19 - 53

(1) Remove the ignition switch from the steering
column. Refer toGroup 8D Ignition System.
(2) Using a key cylinder, check the turning effort of
the switch.
²If the ignition switch binds look for the following
conditions.
(1) Look for rough areas or flash in the casting and
if found remove with a file (Fig. 2).
(2) Remove the link and slider.
(3) Check the link to see if it has been bent and if
so replace with a new part.
Put the slider in its slot in the sleeve and verify a
loose fit over the length of the slot. If the slider binds
in the slot at any point lightly file the slider until
clearance is achieved.
²If no binding is found.
Lightly file the ramp on the ignition switch, (The
ramp fits into the casting) until binding no longer oc-
curs.
AUTOMATIC TRANSMISSION SHIFTER/IGNITION
INTERLOCK MECHANISM
The automatic transmission Shifter/Ignition Inter-
lock, is a cable operated system. It interconnects the
automatic transmission floor mounted shifter to the
steering column ignition switch (Fig. 1). The system
locks the shifter into the PARK position. The Inter-
lock system is engaged whenever the ignition switch
is in the LOCK or ACCESSORY position. When the
key is in the OFF or RUN position the shifter is un-
locked and will move into any position. The interlock
system also prevents the ignition switch from being
turned to the LOCK or ACCESSORY position (Fig.
2). Unless the shifter is fully locked into the PARK
position.
INTERLOCK CABLE REPLACEMENT
REMOVAL
(1) Lower the steering column. Refer to Column
Assembly Replacement in this group.
Fig. 1 Steering Column Non-Serviceable
Components
Fig. 2 Steering Column Flash Removal And
Non-Serviceable Components
Fig. 3 Observe Cautions
Fig. 4 Observe Cautions
JSTEERING 19 - 55

(3) Place the ignition key cylinder in the ACCES-
SORY position.
(4) Remove shipping pin from plastic base.
(5) Connect the cable eyelet to the bellcrank pin
(Fig. 4).
(6) Place gear selector in PARK.
(7) Push the spring-loaded cable adjuster forward
and snap cable into bracket (Fig. 4).
(8) Push the cable adjuster lock clamp downward
to lock it.(9) Install the center console and related trim. Re-
fer to Group 23, Body.
(10) Test the park-lock cable operation.
(11) Load the steering column up to the bracket.
Refer to Column Assembly Replacement in this
group.
TEST/INSPECTION
(1) Turn the ignition switch key to the LOCK posi-
tion.
(2) Press inward on the gear selector handle re-
lease button, the button should not move.
(3) Turn the ignition switch key to the ON posi-
tion.
(4) Press inward on the gear selector handle re-
lease button.
(5) Move the gear selector handle to the DRIVE or
NEUTRAL position.
(6) Attempt to turn the ignition switch key to the
LOCK position.
(7) If the park-lock cable is correctly adjusted, the
key will not turn to the LOCK position.
(8) Press inward on the gear selector handle re-
lease button and move the gear selector handle to the
PARK position.
(9) Turn the ignition switch key to the LOCK posi-
tion. If the park-lock cable is correctly adjusted, the
key will turn to the LOCK position.
(10) If additional cable adjustment is required,
slide the adjuster forward or rearward to obtain the
correct position. Refer to Group 21, Transmission for
additional information involving shift cable adjust-
ment.
Fig. 4 Cable and Shifter
JSTEERING 19 - 57

ANTENNA........................8F-2,8F-5
ANTENNA, POWER; RADIO (XJ-RHD) . . . 8W-47-1
ANTENNA REMOVE/INSTALL - XJ.........8F-8
ANTENNA REMOVE/INSTALL - YJ........8F-10
ANTILOCK BRAKES (ABS)................5-1
ANTILOCK BRAKING MODE, ABS
OPERATION IN.......................5-36
ANTILOCK ECU AND HCU DIAGNOSIS......5-3
APPLICATION CHARTS, GEARTRAIN
OPERATION........................21-169
APPLICATION, TRANSMISSION..........21-67
APPLICATIONÐXJ VEHICLES, BULB......8L-18
APPLICATIONÐYJ VEHICLES, BULB......8L-32
APPLIQUEÐXJ, QUARTER WINDOW.....23-25
APPLIQUEÐYJ, RADIATOR GRILLE.....23-104
APRONSÐYJ, FENDER SPLASH........23-115
ARM, LOWER SUSPENSION.............2-13
ARM, PITMAN..................19-17,19-20
ARM REMOVE/INSTALL, LIFTGATE
WIPER.............................8K-17
ARM REMOVE/INSTALL, WINDSHIELD
WIPER.............................8K-17
ARM, UPPER SUSPENSION.............2-12
ARMING/DISARMING MECHANISM;
RESTRAINT SYSTEMS.................8M-2
ARMING/DISARMING MECHANISM;
STEERING..........................19-48
ARMS AND PUSH RODS, ROCKER....9-23,9-65
ASH RECEIVER TRAY LAMPÐXJ, I/P.....23-80
ASSEMBLY....................19-63,19-71
ASSEMBLY AND ADJUSTMENT, VALVE
BODY.............................21-153
ASSEMBLY, CALIPER...................5-50
ASSEMBLY, COMPRESSOR CLUTCH......24-20
ASSEMBLY, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE................2-38
ASSEMBLY, DIFFERENTIAL; REAR
SUSPENSION AND AXLES...............3-21
ASSEMBLY, FINAL; FRONT SUSPENSION
AND AXLE...........................2-46
ASSEMBLY, FINAL; REAR SUSPENSION
AND AXLES..........................3-29
ASSEMBLY, FUEL RAIL................14-62
ASSEMBLY, GEAR....................19-43
ASSEMBLY, IMPACT SENSOR/INFLATOR . . . 8M-2
ASSEMBLY, PINION MEASUREMENT.......3-22
ASSEMBLY REMOVE/INSTALL, CLUSTER . . 8E-17,
8E-35
ASSEMBLY REPLACEMENT, ADJUSTER
PLUG..............................19-29
ASSEMBLY REPLACEMENT, COLUMN.....19-52
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-23
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...........3-14,3-31
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-24
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...............3-14
ASSEMBLY (SHORT BLOCK), SERVICE
ENGINE..............................9-4
ASSEMBLY TIPS, TRANSMISSION......21-155
ASSEMBLY, TRANSFER CASE
....21-294,21-319
ASSEMBLY/INSTALLATION, PINION GEAR
. . 2-42
ASSEMBLYÐXJ VEHICLES, ENGINE
. . . 9-18,9-59
ASSEMBLYÐYJ VEHICLES, ENGINE
. . . 9-20,9-62
ASSIST HANDLEÐXJ
.................23-89
ASSIST HANDLEÐYJ, FULL-METAL
DOOR
............................23-136
AUTO SHUTDOWN (ASD) RELAYÐPCM
OUTPUT
............................14-26
AUTOMATIC BELT TENSIONERÐXJ
MODELS WITH RIGHT HAND DRIVE
.......7-42
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (YJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ-RHD)
............8W-30-1
AUTOMATIC SHUTDOWN (ASD) RELAY;
FUEL SYSTEM
.......................14-59
AUTOMATIC SHUTDOWN (ASD) RELAY;
IGNITION SYSTEMS
..............8D-17,8D-1AUTOMATIC SHUTDOWN (ASD) RELAY
TEST...............................8D-6
AUTOMATIC SHUTDOWN (ASD) RELAY
TESTING...........................14-46
AUTOMATIC SHUTDOWN (ASD)
SENSEÐPCM INPUT..................14-21
AUTOMATIC TRANSMISSION............0-23
AUTOMATIC TRANSMISSION, 30RH/
32RH..............................21-67
AUTOMATIC TRANSMISSION, AW-4.....21-165
AUTOMATIC TRANSMISSION SHIFTER/
IGNITION INTERLOCK MECHANISM......19-55
AUXILIARY ELECTRIC COOLING FANÐXJ
MODELS WITH 4.0L 6-CYLINDER
ENGINE.............................7-35
AW-4 ACCUMULATOR COMPONENT
IDENTIFICATION....................21-342
AW-4 AUTOMATIC TRANSMISSION......21-165
AW-4 BUSHING AND PISTON
CLEARANCE........................21-339
AW-4 CLUTCH AND BRAKE PACK
REQUIREMENTS....................21-341
AW-4 CLUTCH DISC AND PLATE
THICKNESS........................21-338
AW-4 GENERAL SPECIFICATIONS.......21-337
AW-4 IN-VEHICLE SERVICE............21-182
AW-4 OIL PUMP WEAR LIMITS........21-338
AW-4 RETAINER AND PISTON
SPECIFICATIONS....................21-340
AW-4 TORQUE SPECIFICATIONS........21-344
AW-4 TRANSMISSION DIAGNOSIS......21-176
AW-4 TRANSMISSION OVERHAUL......21-201
AW-4 TRANSMISSION REMOVAL AND
INSTALLATION......................21-198
AW-4 VALVE AND SPRING
IDENTIFICATION....................21-343
AW-4 VALVE BODY CHECK BALL
DIMENSIONS.......................21-341
AWAY, PEDAL FALLS....................5-5
AX 15 MANUAL TRANSMISSION........21-33
AX 4/5 MANUAL TRANSMISSION.........21-1
AXLE (2WD), MODEL 30 AXLE AND
TUBE...............................2-22
AXLE, 8 1/4......................3-30,3-51
AXLE ALIGNMENT, REAR...............3-10
AXLE AND TUBE AXLE (2WD), MODEL
30 .................................2-22
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-23
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES......................3-14,3-31
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-24
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES..........................3-14
AXLE BUSHING REPLACEMENT......2-12,2-34
AXLE, FRONT DRIVE....................2-3
AXLE, MODEL 30.....................2-49
AXLE, MODEL 30 FRONT...............2-49
AXLE, MODEL 35.................3-13,3-51
AXLE NOISE/VIBRATION DIAGNOSIS;
FRONT SUSPENSION AND AXLE..........2-18
AXLE NOISE/VIBRATION DIAGNOSIS;
REAR SUSPENSION AND AXLES
..........3-9
AXLE SHAFT
.........................3-16
AXLE SHAFT, HUB BEARING
.............2-25
AXLE SHAFT OIL SEAL REPLACEMENT,
INNER
..............................2-35
AXLE SHAFT SEAL AND BEARING
........3-17
AXLE SHAFT, SEAL AND BEARING
SERVICE
............................3-32
AXLE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE
................2-49
AXLE SPECIFICATIONS; REAR
SUSPENSION AND AXLES
...............3-51
AXLEÐYJ VEHICLES, VACUUM
DISCONNECT
.........................2-27
AXLES
...............................3-1
AXLES, FRONT AND REAR
..............0-24
AXLE/SHIFT MOTOR DIAGNOSIS
(CONT'D), DISCONNECT
................2-30
AXLE/SHIFT MOTOR DIAGNOSIS,
DISCONNECT
.........................2-29BACKLASH AND CONTACT PATTERN
ANALYSIS; FRONT SUSPENSION AND
AXLE...............................2-45
BACKLASH AND CONTACT PATTERN
ANALYSIS; REAR SUSPENSION AND
AXLES..............................3-27
BACK-UP LAMPS; REAR LIGHTING (XJ) . 8W-51-1
BACK-UP LAMPS; REAR LIGHTING
(XJ-RHD).........................8W-51-1
BACK-UP LAMPS; REAR LIGHTING (YJ) . 8W-51-1
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐXJ........8L-12
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐYJ........8L-28
BALANCE, TIRE AND WHEEL............22-6
BALL DIMENSIONS, AW-4 VALVE BODY
CHECK............................21-341
BALL STUD REPLACEMENTÐXJ,
LIFTGATE SUPPORT ROD..............23-63
BALL STUDS, STEERING KNUCKLE.......2-32
BAR, STABILIZER; FRONT SUSPENSION
AND AXLE.......................2-11,2-15
BAR, STABILIZER; REAR SUSPENSION
AND AXLES...........................3-5
BAR, TRACK; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
BAR, TRACK; REAR SUSPENSION AND
AXLES...............................3-8
BARÐXJ, SOUND....................23-94
BARÐYJ, SPORT...................23-132
BARRIERÐXJ, CARGO...............23-101
BASE COAT/CLEAR COAT FINISH.........23-158
BATTERY; BATTERY/STARTER/
GENERATOR SERVICE..................8B-1
BATTERY; BATTERY/STARTING/
CHARGING SYSTEMS DIAGNOSTICS......8A-2
BATTERY; LUBRICATION AND
MAINTENANCE.......................0-20
BATTERY CHARGING...................8A-7
BATTERY CHARGING TIME TABLE........8A-8
BATTERY CLASSIFICATIONS AND
RATINGS...........................8A-23
BATTERY DIAGNOSIS..................8A-4
BATTERY FEED; FUEL/IGNITION (XJ) . . . 8W-30-1
BATTERY FEED; FUEL/IGNITION (YJ) . . . 8W-30-2
BATTERY FEED; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
BATTERY RATINGS....................8A-3
BATTERY REMOVE/INSTALL.............8B-1
BATTERY SPECIFICATIONS; BATTERY/
STARTER/GENERATOR SERVICE..........8B-8
BATTERY SPECIFICATIONS; BATTERY/
STARTING/CHARGING SYSTEMS
DIAGNOSTICS.......................8A-23
BATTERY TRAYÐXJ..................23-14
BATTERY TRAYÐYJ.................23-110
BATTERY VOLTAGEÐPCM INPUT........14-21
B/C-PILLAR AND LIFTGATE PILLAR TRIM
COVERSÐXJ........................23-88
BEARING AND AXLE SHAFT, HUB.........2-25
BEARING, AXLE SHAFT SEAL............3-17
BEARING LUBRICANTS, CHASSIS
COMPONENT AND WHEEL..............0-28
BEARING NOISE, GEAR; FRONT
SUSPENSION AND AXLE................2-18
BEARING NOISE, GEAR; REAR
SUSPENSION AND AXLES................3-9
BEARING REPLACEMENT, PILOT..........6-12
BEARING REPLACEMENT, PITMAN
SHAFT SEALS.......................19-34
BEARING REPLACEMENT, RELEASE.......6-11
BEARING SERVICE, AXLE SHAFT, SEAL....3-32
BEARINGS, CRANKSHAFT MAIN......9-45,9-87
BEARINGS, FRONT WHEEL..............0-28
BELT, ACCESSORY DRIVE...............0-21
BELT DIAGNOSIS......................7-38
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ).........8W-40-2
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
BELT SCHEMATICS....................7-38
BELT SERVICEÐEXCEPT RIGHT HAND
DRIVE
..............................7-40
BELT SERVICEÐXJ MODELS WITH
RIGHT HAND DRIVE
...................7-42
BELT SWITCH, DRIVER'S SEAT
......8U-1,8U-3
BELT TENSION, DRIVE
.................7-45
BELT TENSION SPECIFICATIONS
..........7-38
2 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

INSTALLATION, DRUM BRAKESHOE.......5-55
INSTALLATION, FRONT WHEEL SENSOR . . . 5-38
INSTALLATION METHODS AND PARTS
USAGE...............................6-4
INSTALLATION (NON-ABS), MASTER
CYLINDER...........................5-16
INSTALLATION, ROTOR.................5-51
INSTALLATION, TRANSFER CASE . 21-288,21-309
INSTALLATION, TRANSMISSION.....21-36,21-5
INSTALLATION, TRANSMISSION AND
CONVERTER.......................21-117
INSTALLATION, TRANSMISSION AND
TORQUE CONVERTER................21-199
INSTALLATION, TRANSMISSION VALVE
BODY.............................21-187
INSTALLATION, VALVE BODY..........21-104
INSTALLATION, WHEEL.................22-6
INSTALLATION, WHEEL CYLINDER........5-58
INSTALLATION (WITH ABS), MASTER
CYLINDER AND COMBINATION VALVE.....5-20
INSTALLATION (XJ), HCU...............5-43
INSTALLATION (XJ MODELS), ECU........5-40
INSTALLATION (XJ), SHIFT LEVER......21-286,
21-309
INSTALLATION (XJ WITH ABS), POWER
BRAKE BOOSTER.....................5-27
INSTALLATION (XJ WITH FULL
CONSOLE), PARKING BRAKE LEVER.......5-64
INSTALLATION (XJ WITH MINI
CONSOLE), PARKING BRAKE LEVER.......5-63
INSTALLATION (XJ WITHOUT ABS),
POWER BRAKE BOOSTER...............5-30
INSTALLATION (XJ WITHOUT CONSOLE),
PARKING BRAKE LEVER................5-65
INSTALLATION (YJ), HCU...............5-44
INSTALLATION (YJ), PARKING BRAKE
PEDAL..............................5-66
INSTALLATION (YJ), POWER BRAKE
BOOSTER............................5-30
INSTALLATION (YJ), SHIFT LEVER......21-286
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (XJ).....................8W-40-1
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-1
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (YJ).....................8W-40-1
INSTRUMENT CLUSTER AND GAUGE
HOUSINGSÐYJ.....................23-151
INSTRUMENT CLUSTER BEZELÐXJ......23-80
INSTRUMENT CLUSTER BEZELÐYJ.....23-151
INSTRUMENT CLUSTERS..........8E-24,8E-1
INSTRUMENT PANEL.............8E-24,8E-1
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-24
INSTRUMENT PANEL COMPONENTSÐYJ . 23-152
INSTRUMENT PANEL ILLUMINATION
LAMPS; INTERIOR LIGHTING (XJ).....8W-44-1
INSTRUMENT PANEL ILLUMINATION
LAMPS; INTERIOR LIGHTING (XJ-RHD) . 8W-44-1
INSTRUMENT PANEL REMOVE/INSTALL . . . 8E-20
INSTRUMENT PANELÐYJ.............23-151
INSULATOR PANELÐXJ, DASH PANEL....23-12
INSULATOR PANELÐYJ, HOOD........23-107
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (XJ)................8W-30-4
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (YJ)................8W-30-4
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (XJ-RHD)............8W-30-4
INTAKE DUCT, FRESH AIR..............24-34
INTAKE MANIFOLD...................14-63
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR; FUEL SYSTEM...............14-60
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-23,8D-5
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-46
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-11
INTAKE MANIFOLD AIR TEMPERATURE
SENSORÐPCM INPUT................14-22
INTAKE MANIFOLD LEAKAGE DIAGNOSIS . . . 9-5
INTAKE MANIFOLDÐ2.5L ENGINE........11-7
INTAKE MANIFOLDÐ4.0L ENGINE
........11-8
INTERCHANGEABILITY, TRANSMISSION
CHANGES AND PARTS
................21-67
INTERFERENCE, RADIO FREQUENCY
......8F-5
INTERIOR COMPONENTS
........23-151,23-80
INTERIOR LAMPS
...............8L-16,8L-31INTERIOR LAMPSÐXJ................8L-18
INTERIOR LAMPSÐYJ................8L-32
INTERIOR REARVIEW MIRROR
SUPPORT BRACKET REPLACEMENTÐ
XJ ................................23-68
INTERIOR REARVIEW MIRRORÐXJ......23-66
INTERIOR TRIM PANELS AND SCUFF
PLATESÐXJ........................23-84
INTERLOCK CABLE ADJUSTMENT, PARK . 21-195
INTERLOCK CABLE ADJUSTMENT (XJ),
PARK .............................21-101
INTERLOCK MECHANISM, AUTOMATIC
TRANSMISSION SHIFTER/IGNITION......19-55
INTERMEDIATE (COUPLER) SHAFT.......19-45
INTERMEDIATEÐCOUPLING SHAFT......19-23
INTERMITTENT AND POOR
CONNECTIONS; WIRING DIAGRAMSÐ
GENERAL INFORMATION (XJ)...........8W-4
INTERMITTENT WIPE MODULE..........8K-4
INTERMITTENT WIPE SWITCH TESTING . . 8K-15
INTERMITTENT WIPERS; WIPERS
(XJ-RHD).........................8W-53-1
INTERNATIONAL SYMBOLS...............0-1
INTERNATIONAL VEHICLE CONTROL
AND DISPLAY SYMBOLS.............Intro.-5
INTRODUCTION; BODY COMPONENTSÐ
XJ VEHICLES.......................23-158
INTRODUCTION; LUBRICATION AND
MAINTENANCE.....................0-1,0-4
IN-VEHICLE SERVICE, 30RH/32RH.......21-99
IN-VEHICLE SERVICE, AW-4.............21-182
I/P ASH RECEIVER TRAY LAMPÐXJ.....23-80
JACK STORAGEÐXJ..................23-97
JAMB SWITCH, DRIVER'S DOOR.....8U-1,8U-2
JEEP BODY CODE LETTERS..............5-2
JOINT ANGLE MEASUREMENT,
UNIVERSAL..........................16-4
JOINT REPLACEMENT, UNIVERSAL.......16-10
JOINTS, UNIVERSAL...................16-2
JUMP STARTING PROCEDURE............0-9
JUMP STARTING, TOWING AND
HOISTING............................0-9
KEY CYLINDER SERVICE, IGNITION
SWITCH............................8D-26
KEY LOCK CYLINDERÐXJ, DOOR.......23-47
KEY LOCK CYLINDERÐYJ, FULL-METAL
DOOR............................23-139
KEY-IN SWITCH, IGNITION..........8U-1,8U-2
KEYLESS ENTRY MODULE..........8P-1,8P-7
KEYLESS ENTRY MODULE, REMOTE . . . 8W-61-1
KEYLESS ENTRY MODULE REMOVE/
INSTALL...........................8P-10
KEYLESS ENTRY RECEIVER.............8C-1
KEYLESS ENTRY RECEIVERÐXJ........23-93
KEYLESS ENTRY TRANSMITTER . 8P-1,8P-7,8P-8
KEYS ARE NOT AVAILABLE, TOWING
WHEN..............................0-13
KNOCK, LOW SPEED; FRONT
SUSPENSION AND AXLE................2-19
KNOCK, LOW SPEED; REAR
SUSPENSION AND AXLES...............3-10
KNUCKLE AND BALL STUDS, STEERING . . . 2-32
LABEL, VEHICLE EMISSION CONTROL
INFORMATION (VECI)..................25-1
LABEL, VEHICLE SAFETY CERTIFICATION . Intro.-4
LABELS AND PLATESÐXJ, VEHICLE....Intro.-2
LABELS AND PLATESÐYJ, VEHICLE....Intro.-3
LABELS/DECALS/PLATESÐXJ............23-1
LABELS/DECALS/PLATESÐYJ..........23-102
LABELS/PLATES, CODES AND
DIMENSIONS, DESIGNATIONS.........Intro.-1
LAG TEST, TIME....................21-178
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (XJ)......................8W-32-2
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-2
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (YJ)......................8W-32-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (XJ)
.....................8W-40-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (XJ-RHD)
................8W-40-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (YJ)
.....................8W-40-2
LAMP, ACCESSORY LAMP AND HEATER
CONTROL PANEL
..................8W-44-1
LAMP ADJUSTMENT USING ALIGNMENT
SCREENÐXJ, HEADLAMP/FOG
...........8L-7LAMP ADJUSTMENT USING ALIGNMENT
SCREENÐYJ, HEADLAMP/FOG..........8L-23
LAMP AND DOME LAMP, CARGO......8W-44-1
LAMP AND HEATER CONTROL PANEL
LAMP, ACCESSORY.................8W-44-1
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (XJ).....................8W-40-2
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-2
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (YJ).....................8W-40-2
LAMP BULB REMOVE/INSTALL,
READING/COURTESY..................8C-8
LAMP BULB REPLACEMENTÐXJ,
BACK-UP/REAR TURN SIGNAL/TAIL......8L-12
LAMP BULB REPLACEMENTÐXJ, FRONT
PARK/TURN SIGNAL...................8L-9
LAMP BULB REPLACEMENTÐXJ, SIDE
MARKER...........................8L-10
LAMP BULB REPLACEMENTÐXJ,
UNDERHOOD........................8L-13
LAMP BULB REPLACEMENTÐYJ,
BACK-UP/REAR TURN SIGNAL/TAIL......8L-28
LAMP BULB REPLACEMENTÐYJ, FRONT
PARK/TURN SIGNAL..................8L-25
LAMP BULB REPLACEMENTÐYJ, SIDE
MARKER...........................8L-25
LAMP BULB REPLACEMENTÐYJ,
UNDERHOOD........................8L-29
LAMP BULB REPLACEMENTÐYJ
VEHICLES, HARDTOP DOME/CARGO.....8L-31
LAMP, CARGO LAMP AND DOME;
INTERIOR LIGHTING (XJ-RHD)........8W-44-1
LAMP, CARGO LAMP, COURTESY LAMPS
AND DOME; INTERIOR LIGHTING (XJ) . . 8W-44-1
LAMP, CHARGING SYSTEM INDICATOR;
INSTRUMENT CLUSTER (XJ).........8W-40-3
LAMP (CHMSL)ÐXJ, CENTER HIGH
MOUNTED STOP.....................8L-12
LAMP (CHMSL)ÐYJ, CENTER HIGH
MOUNTED STOP.....................8L-28
LAMP, COURTESY LAMPS AND DOME
LAMP, CARGO; INTERIOR LIGHTING
(XJ).............................8W-44-1
LAMP DIAGNOSIS, FOG...........8L-21,8L-3
LAMP (DRL) MODULE, DAYTIME
RUNNING; FRONT LIGHTING (XJ).....8W-50-2
LAMP (DRL) MODULEÐCANADIAN
VEHICLES ONLY, DAYTIME RUNNING;
FRONT LIGHTING (YJ)..............8W-50-2
LAMP, ENGINE COOLANT TEMPERATURE
WARNING; INSTRUMENT CLUSTER
(XJ).............................8W-40-1
LAMP, ENGINE COOLANT TEMPERATURE
WARNING; INSTRUMENT CLUSTER
(XJ-RHD).........................8W-40-1
LAMP, GLOVE BOX; INTERIOR LIGHTING
(XJ).............................8W-44-1
LAMP, GLOVE BOX; INTERIOR LIGHTING
(XJ-RHD).........................8W-44-1
LAMP, HIGH-BEAM INDICATOR;
INSTRUMENT CLUSTER (XJ).........8W-40-2
LAMP, HIGH-BEAM INDICATOR;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
LAMP HOUSINGÐXJ, LIFTGATE LICENSE
PLATE .............................23-65
LAMP, IGNITION SWITCH; INTERIOR
LIGHTING (XJ)....................8W-44-1
LAMP, IGNITION SWITCH; INTERIOR
LIGHTING (XJ-RHD)................8W-44-1
LAMP, LOW FUEL WARNING;
INSTRUMENT CLUSTER (XJ).........8W-40-1
LAMP, LOW WASHER FLUID WARNING;
INSTRUMENT CLUSTER (XJ).........8W-40-2
LAMP, LOW WASHER FLUID WARNING;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
LAMP, MANUAL TRANSMISSION
UP-SHIFT; INSTRUMENT CLUSTER (XJ) . 8W-40-2
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (XJ)
................8W-30-5
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (YJ)
................8W-30-5
LAMP (MIL), MALFUNCTION INDICATOR;
INSTRUMENT CLUSTER (XJ)
.........8W-40-2
LAMP (MIL), MALFUNCTION INDICATOR;
INSTRUMENT CLUSTER (XJ-RHD)
.....8W-40-1
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (XJ-RHD)
............8W-30-4
JINDEX 15
Description Group-Page Description Group-Page Description Group-Page

MASTER CYLINDER, CLUTCH............0-22
MASTER CYLINDER INSTALLATION
(NON-ABS)..........................5-16
MASTER CYLINDER OVERHAUL
(4-CYLINDER MODELS)................5-16
MASTER CYLINDER REMOVAL
(NON-ABS)..........................5-15
MASTER CYLINDERÐCOMBINATION
VALVE ..............................5-15
MASTER CYLINDER/POWER BOOSTER
TEST................................5-8
MASTER CYLINDER/POWER BRAKE
BOOSTER............................5-34
MATCH MOUNTING....................22-7
MATERIAL, BRAKELINING................5-1
MATSÐXJ, CARPETS AND FLOOR.......23-99
MEASUREMENT AND ADJUSTMENT,
DIFFERENTIAL SHIM PACK..............2-43
MEASUREMENT AND ASSEMBLY, PINION . . 3-22
MEASUREMENT AND INSTALLATION,
DIFFERENTIAL........................3-25
MEASUREMENT AND TORQUE
SPECIFICATIONS...................Intro.-11
MEASUREMENT, DIFFERENTIAL AND
PINION.............................2-40
MEASUREMENT, UNIVERSAL JOINT
ANGLE..............................16-4
MEASUREMENTS AND ADJUSTMENTS,
ALIGNMENT...........................2-8
MEASURING WITH PLASTIGAGE..........9-3
MECHANISM, ARMING/DISARMING;
RESTRAINT SYSTEMS..................8M-2
MECHANISM, ARMING/DISARMING;
STEERING..........................19-48
MECHANISM, AUTOMATIC
TRANSMISSION SHIFTER/IGNITION
INTERLOCK.........................19-55
MECHANISM, SHIFT.................21-307
MEMORY, RADIO; RADIO (XJ)........8W-47-1
MEMORY, RADIO; RADIO (XJ-RHD)....8W-47-1
MEMORY, RADIO; RADIO (YJ)........8W-47-1
METAL DOOR MIRROR (EXTERNAL)Ð
YJ, HALF..........................23-121
METHODS AND PARTS USAGE,
INSTALLATION.........................6-4
METRIC AND ENGLISH/SAE
CONVERSION.....................Intro.-11
METRIC CONVERSION..............Intro.-16
METRIC, THREAD NOTATIONÐSAE....Intro.-13
(MFI)ÐCOMPONENT DESCRIPTION/
SYSTEM OPERATION, MULTI-PORT
FUEL INJECTION.....................14-19
(MFI)ÐCOMPONENT REMOVAL/
INSTALLATION, MULTI-PORT FUEL
INJECTION..........................14-58
(MFI)ÐGENERAL DIAGNOSIS,
MULTI-PORT FUEL INJECTION..........14-35
MINI-CONSOLE WITH FLOOR SHIFTÐXJ . . 23-94
MINI-FLOOR CONSOLEÐXJ............23-94
MIRROR (EXTERNAL)ÐYJ, HALF METAL
DOOR............................23-121
MIRROR LAMPS, VISOR VANITY;
INTERIOR LIGHTING (XJ)............8W-44-2
MIRROR LAMPS, VISOR VANITY;
INTERIOR LIGHTING (XJ-RHD)........8W-44-1
MIRROR, POWER.....................8T-1
MIRROR REMOVE/INSTALL, POWER
......8T-4
MIRROR RETAINING BRACKETÐYJ,
REARVIEW
.........................23-144
MIRROR SUPPORT BRACKET
REPLACEMENTÐXJ, INTERIOR
REARVIEW
..........................23-68
MIRROR SWITCH CONTINUITY (LEFT
POSITION), POWER
....................8T-3
MIRROR SWITCH CONTINUITY (RIGHT
POSITION), POWER
....................8T-3
MIRROR SWITCH, POWER
..........8T-1,8T-2
MIRROR SWITCH REMOVE/INSTALL,
POWER
.............................8T-4
MIRROR SYSTEM, POWER
..............8T-1
MIRROR TROUBLE DIAGNOSISÐXJ,
LIGHTED VANITY
.....................8L-16
MIRRORÐXJ, INTERIOR REARVIEW
.....23-66
MIRRORÐXJ, LIGHTED VANITY
.........8L-16
MIRRORÐYJ, REARVIEW
.............23-144
MIRRORS, POWER; POWER MIRRORS
(XJ)
.............................8W-62-1MIRRORS, POWER; POWER MIRRORS
(XJ-RHD).........................8W-62-1
MIRRORSÐXJ, EXTERNAL.............23-27
MISALIGNMENT, CLUTCH................6-3
MISALIGNMENT, CLUTCH HOUSING........6-4
MISS, INJECTOR DIAGNOSISÐVEHICLE
RUNS ROUGH AND/OR HAS A..........14-52
MODE, ABS OPERATION IN ANTILOCK
BRAKING............................5-36
MODE, ABS OPERATION IN NORMAL
BRAKING............................5-35
MODEL 30 AXLE......................2-49
MODEL 30 AXLE AND TUBE AXLE (2WD) . . 2-22
MODEL 30 FRONT AXLE................2-49
MODEL 35 AXLE..................3-13,3-51
MODELS, BELT TENSIONÐEXCEPT
RIGHT HAND DRIVE (RHD)..............7-45
MODELS, IGNITION SWITCHÐXJ........8D-26
MODELS, IGNITION SWITCHÐYJ........8D-29
MODELS WITH 4.0L 6-CYLINDER
ENGINE, AUXILIARY ELECTRIC
COOLING FANÐXJ....................7-35
MODELS WITH RIGHT HAND DRIVE,
AUTOMATIC BELT TENSIONERÐXJ.......7-42
MODELS WITH RIGHT HAND DRIVE,
BELT SERVICEÐXJ....................7-42
MODES OF OPERATION, OPEN
LOOP/CLOSED LOOP..................14-30
MODULE, AIRBAG....................8M-1
MODULE, BUZZER................8U-1,8U-2
MODULE, CHIME/BUZZER; INTERIOR
LIGHTING (XJ)....................8W-44-2
MODULE, CHIME/BUZZER; INTERIOR
LIGHTING (XJ-RHD)................8W-44-2
MODULE, DAYTIME RUNNING LAMP
(DRL); FRONT LIGHTING (XJ)........8W-50-2
MODULE, DIMMING; FRONT LIGHTING
(XJ-RHD).........................8W-50-1
MODULE, FUEL PUMP; FUEL SYSTEM....14-61,
14-3
MODULE, FUEL PUMP; FUEL/IGNITION
(XJ).............................8W-30-2
MODULE, FUEL PUMP; FUEL/IGNITION
(YJ).............................8W-30-2
MODULE, FUEL PUMP; FUEL/IGNITION
(XJ-RHD).........................8W-30-2
MODULE HANDLING, AIRBAG...........8M-2
MODULE, HEADLAMP DELAY; FRONT
LIGHTING (XJ)....................8W-50-2
MODULE, HEADLAMP DELAY; FRONT
LIGHTING (XJ-RHD)................8W-50-1
MODULE, INTERMITTENT WIPE..........8K-4
MODULE, KEYLESS ENTRY.........8P-1,8P-7
MODULE (PCM) 60-WAY CONNECTOR,
POWERTRAIN CONTROL...............14-40
MODULE (PCM), POWERTRAIN
CONTROL; EMISSION CONTROL
SYSTEMS...........................25-7
MODULE (PCM), POWERTRAIN
CONTROL; FUEL SYSTEM.........14-20,14-64
MODULE (PCM), POWERTRAIN
CONTROL; IGNITION SYSTEMS....8D-11,8D-23,
8D-5
MODULE, POWERTRAIN CONTROL . . . 8H-1,8H-7
MODULE, REMOTE KEYLESS ENTRY . . . 8W-61-1
MODULE REMOVE/INSTALL, AIRBAG.....8M-3
MODULE REMOVE/INSTALL, KEYLESS
ENTRY.............................8P-10
MODULE REMOVEÐINSTALL, AIRBAG....19-49
MODULE REPLACEMENTÐXJ, DRL......8L-15
MODULE REPLACEMENTÐXJ,
HEADLAMP DELAY...................8L-14
MODULE REPLACEMENTÐYJ, DRL......8L-30
MODULE SCHEMATIC - YJ, BUZZER......8U-4
MODULE (TCM) SERVICE,
TRANSMISSION CONTROL............21-183
MODULE, TRANSMISSION CONTROL;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
MODULEÐ4.0L ENGINE ONLY,
TRANSMISSION CONTROL;
TRANSMISSION CONTROLS (XJ)......8W-31-1
MODULEÐCANADIAN VEHICLES ONLY,
DAYTIME RUNNING LAMP (DRL)
......8W-50-2
MODULEÐXJ, SENTINEL HEADLAMP
DELAY
.............................8L-14
MOLDING/CLADDINGÐXJ, BODY SIDE
. . . 23-20
MOLDINGÐXJ, DRIP RAIL
.............23-25
MOLDINGÐXJ, WINDSHIELD REVEAL
....23-66MOLDINGÐXJ, WINDSHIELD SIDE......23-86
MOLDINGÐYJ, BODY SIDE STEP.......23-115
MOLDINGÐYJ, WINDSHIELD REVEAL . . . 23-144
MOLDINGSÐXJ, DOOR WINDOW
EXTERIOR..........................23-54
MOTOR, A/C BLOWER.................24-35
MOTOR, A/C-HEATER BLOWER; AIR
CONDITIONING/HEATER (YJ).........8W-42-2
MOTOR, BLOWER; AIR CONDITIONING/
HEATER (XJ)......................8W-42-1
MOTOR, BLOWER; AIR CONDITIONING/
HEATER (XJ-RHD)..................8W-42-1
MOTOR, BLOWER; HEATING AND AIR
CONDITIONING......................24-17
MOTOR DIAGNOSIS (CONT'D),
DISCONNECT AXLE/SHIFT...............2-30
MOTOR DIAGNOSIS, DISCONNECT
AXLE/SHIFT..........................2-29
MOTOR, FRESH AIR DOOR VACUUM.....24-34
MOTOR (HEATING), BLOWER...........24-33
MOTOR, IDLE AIR CONTROL (IAC); FUEL
SYSTEM............................14-62
MOTOR, IDLE AIR CONTROL (IAC);
FUEL/IGNITION (XJ)................8W-30-2
MOTOR, IDLE AIR CONTROL (IAC);
FUEL/IGNITION (YJ)................8W-30-2
MOTOR, IDLE AIR CONTROL (IAC);
FUEL/IGNITION (XJ-RHD)............8W-30-2
MOTOR, POWER LOCK.............8P-1,8P-7
MOTOR, POWER WINDOW..........8S-1,8S-2
MOTOR, RADIATOR FAN RELAY; AIR
CONDITIONING/HEATER (XJ).........8W-42-2
MOTOR, RADIATOR FAN RELAY; AIR
CONDITIONING/HEATER (XJ-RHD).....8W-42-2
MOTOR RELAY, ABS PUMP; ANTI-LOCK
BRAKES (XJ)......................8W-32-1
MOTOR RELAY, ABS PUMP; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-1
MOTOR RELAY, ABS PUMP; ANTI-LOCK
BRAKES (YJ)......................8W-32-1
MOTOR RELAY TEST, STARTER.........14-51
MOTOR REMOVE/INSTALL, LIFTGATE
WIPER.........................8K-20,8K-6
MOTOR REMOVE/INSTALL, POWER
LOCK...............................8P-8
MOTOR REMOVE/INSTALL, POWER
WINDOW............................8S-7
MOTOR REMOVE/INSTALL, WINDSHIELD
WIPER.........................8K-19,8K-6
MOTOR REPLACEMENT, A/C
RECIRCULATING DOOR VACUUM........24-27
MOTOR REPLACEMENT, HEATER/
DEFROSTER/INSTRUMENT PANEL
OUTLET VACUUM....................24-26
MOTOR RESISTORS REPLACEMENT,
BLOWER...........................24-31
MOTOR SPEED SENSOR, PUMP;
ANTI-LOCK BRAKES (XJ)............8W-32-2
MOTOR SPEED SENSOR, PUMP;
ANTI-LOCK BRAKES (XJ-RHD)........8W-32-2
MOTOR SPEED SENSOR, PUMP;
ANTI-LOCK BRAKES (YJ)............8W-32-1
MOTOR SWITCH, BLOWER.............24-16
MOTOR SWITCH REPLACEMENT,
BLOWER MOTOR/AIR DOOR............24-32
MOTOR TEST, IDLE AIR CONTROL.......14-49
MOTOR/AIR DOOR MOTOR SWITCH
REPLACEMENT, BLOWER
..............24-32
MOTOR/FAN REPLACEMENT, BLOWER
....24-24
MOTORÐPCM OUTPUT, IDLE AIR
CONTROL (IAC)
......................14-27
MOUNTED STOP LAMP (CHMSL)ÐXJ,
CENTER HIGH
.......................8L-12
MOUNTED STOP LAMP (CHMSL)ÐYJ,
CENTER HIGH
.......................8L-28
MOUNTING, MATCH
...................22-7
MOUNTÐREAR, ENGINE
...........9-16,9-57
MOUNTSÐFRONT, ENGINE
..........9-14,9-56
MUFFLER AND EXHAUST TAILPIPEÐXJ
VEHICLES
...........................11-5
MUFFLER AND EXHAUST TAILPIPEÐYJ
VEHICLES
...........................11-6
MULTI-FUNCTION SWITCH - XJ
..........8J-4
MULTI-FUNCTION SWITCH REMOVE/
INSTALL - XJ
.........................8J-5
MULTI-FUNCTION SWITCH SERVICE
PROCEDURESÐXJ
...................8L-11
18 INDEXJ
Description Group-Page Description Group-Page Description Group-Page