1995 JEEP CHEROKEE roof rack

(2) Ensure that all the retainer clips, screws and
Velcro strips are disengaged before removing the
headliner.
HEADLINER INSTALLATION
(1) When installing a headliner, ensure that the re-
tainer clips and rails are installed (Fig. 4 and 5).
(2) Install the upper trim moldings around the pe-
rimeter of the headliner. Tighten the retaining
screws to 1 Nzm (11 in-lbs) torque.
(3) As applicable, install:
²Assist handles.
²Sunvisors.
²Dome/cargo lamps.
²Overhead console.
²Keyless entry receiver module.
²Sound bar.
²All other attached/overlapping components.
DOME LAMPÐXJ
REMOVAL
(1) Remove the dome lamp lens by squeezing both
sides to release the retaining clips. Pull downward to
remove the lens.
(2) Remove the speed nuts (Fig. 6).
(3) Disconnect the wire harness connector.
(4) Remove the lamp from the headliner.
INSTALLATION
(1) Connect the dome lamp wire harness connector.
(2) Position the dome lamp in the headliner hole
and install the speed nuts.
(3) Install the dome lamp lens.
OVERHEAD CONSOLEÐXJ
Refer to Group 8C, Overhead Console for removal
and installation procedure.
KEYLESS ENTRY RECEIVERÐXJ
Refer to Group 8P, Keyless Entry for removal and
installation procedure.
SUNVISORSÐXJ
REMOVAL
(1) Remove the screws that attach the sunvisor
arm support bracket to the headliner and the roof
panel (Fig. 7).
(2) Detach the sunvisor from the support clip.
(3) Remove the sunvisor from the vehicle.
(4) Remove the retaining screw and support clip.
Fig. 4 Headliner Retainer Clip and Retainer Rail
Fig. 5 Headliner Correctly Installed
Fig. 6 Dome Lamp
JINTERIOR COMPONENTSÐXJ 23 - 93

INSTALLATION
(1) Install the support bracket and the retaining
screw. Tighten the screw to 1 Nzm (9 in-lbs) torque.
(2) Position the sunvisor in the support clip and
align the arm support bracket holes with the head-
liner holes.
(3) Install the screws that attach the sunvisor arm
support bracket to the headliner and the roof panel.
Tighten the screws to 4 Nzm (35 in-lbs) torque.
SOUND BARÐXJ
REMOVAL
(1) Disconnect battery negative cable.
(2) Remove left and right upper trim molding.
(3) Remove sound bar screws.
(4) Separate sound bar from roof.
(5) Disconnect speaker connector.
(6) Disconnect cargo lamp connector.
(7) Remove sound bar from vehicle (Fig. 8).
INSTALLATION
(1) Position sound bar in vehicle.
(2) Connect speaker connecter.
(3) Connect cargo lamp connector.
(4) Position sound bar at roof.
(5) Install sound bar screws.
(6) Install left and right upper trim molding.
(7) Connect battery negative cable.
CARGO LAMPÐXJ
REMOVAL
(1) Remove the cargo lamp lens (Fig. 8) by squeez-
ing both sides to release the retaining clips. Pull
downward to remove the lens.
(2) Remove the push nuts.
(3) Disconnect the wire harness connector.
(4) Remove the lamp from the sound bar.
INSTALLATION
(1) Connect the cargo lamp wire harness connector.
(2) Position the cargo lamp in the sound bar hole
and install the push nuts.
(3) Install the cargo lamp lens.
MINI-FLOOR CONSOLEÐXJ
Mini-consoles are installed in XJ vehicles with and
without a transmission floor shift (Fig. 1).
PARKING BRAKE HANDLE COVERÐXJ
REMOVAL
(1) Detach the rear of the cover from the base and
pivot it upward (Fig.2).
(2) Remove the retaining screws from the cover
base.
(3) Remove the trim cover from the from the floor.
INSTALLATION
(1) Position the cover on the floor and install the
retaining screws.
(2) Pivot the cover to the closed position and en-
gage the locking tab.
MINI-CONSOLE WITH FLOOR SHIFTÐXJ
REMOVAL
(1) Remove the transmission shift lever handle/
knob. For vehicles with an automatic transmission,
pull the handle straight up. For vehicles with a man-
ual transmission, loosen the locknut and un-thread
the shift knob from the shaft.
(2) Remove the automatic transmission and trans-
fer case shift indicator bezel by prying upward to re-
lease them (Fig. 3).
(4) Disconnect the lamp socket from the bezel.
(5) Remove the console retaining screws.
(6) Disconnect the wire harness connector.
Fig. 7 Sunvisor Removal/Installation
Fig. 8 Sound Bar Removal/Installation
23 - 94 INTERIOR COMPONENTSÐXJJ

HARD TOP ROOF VENTÐYJ
REMOVAL/INSTALLATION
(1) Remove the roof vent retaining screw from the
spring nut (Fig. 1).
(2) Remove the roof vent from the hard top.
(3) Position the roof vent on the hard top and in-
stall the retaining screw.
HARD TOP REPAIRÐYJ
The hard top fiberglass material can be repaired.
The required repair materials include:
²Fiberglass mat or cloth.
²Fiberglass resin and hardener.
²structural adhesive (3M brand or an equivalent
product).
²Glazing putty.
²Aluminum foil.
²Plastic spreader.
HARD TOP HOLE REPAIR
(1) Use a grinder to remove the paint and outline
the damaged area. Use a grade 24 grit disc for paint
removal.
(2) Grind the outlined surface area again to a 50
grit disc to prevent coarse scratches from appearing
in the final finish.
(3) If cracks extend from the hole, it will be neces-
sary to stop-drill the crack(s) with a 3-mm (1/8-in) di-
ameter drill bit.
(4) Position a fiberglass mat or cloth on the repair
surface area. Cut the mat to allow a 2.5-cm (1-in)
overlap of the repair surface area.
(5) Clean the repair surface area.
(6) Place the fiberglass cloth on aluminum foil.
(7) Pour the fiberglass resin into a clean container.
(8) Mix the appropriate amount of hardener and
resin. Follow the manufacturers instructions.
(9) Apply the hardener/resin mixture to both sides
of the fiberglass cloth.(10) Place the fiberglass cloth over the repair sur-
face area. Next, place the aluminum foil over the
cloth. Use a plastic spreader to smooth-out the cloth
and resin. Use firm pressure to remove air bubbles
and to smooth-out the cloth.
(11) Allow the resin to cure.
(12) Smooth-out the surface area to the contour of
the hard top with a 50-grit disc.
(13) Apply plastic filler to complete the repair. Fin-
ish smoothing the surface area with 80-grit paper.
(14) Repeat the previous step on the inside surface
area of the hard top.
(15) Featheredge the repaired surface area.
(16) Prime the repaired surface area with Ditzler
Epoxy Chromate Primer (DP-40/401), or an equiva-
lent product.
(17) Apply surface primer to the surface area.
(18) Sand the surface area for paint preparation.
After sanding, re-prime the surface area, if necessary.
(19) Prime the surface area for the color coat.
(20) Color coat the repaired surface area.
FRACTURE REPAIR
(1) Use a grinder to remove the paint (from both,
the inner and outer surface areas of the hard top)
and to outline the damaged area.
(2) Stop-drill the crack(s) with a 3-mm (1/8-in) di-
ameter drill bit.
(3) Bevel the edges of the crack(s) on both sides
with a rotary file.
The edges should be beveled on the inside
and outside of the top to ensure sufficient sur-
face area for good bonding.
(4) Complete the repairs with fiberglass cloth and
resin as described above in the hard top hole repair
procedure.
TEXTURED PAINT REPAIR
The textured paint applied to hard tops is available
from Mopar Parts sources. The paint supplied will
duplicate the original texture on the hard top.
SOFT TOP SERVICE INFORMATIONÐYJ
The soft top fabric consists of the top cover and the
side and rear curtains (Fig. 4). The top cover is sup-
ported by a tubular bow (frame) and is attached to
the upper side retainers (above the doors) with
snap-on retainers (Fig. 5).
Fig. 3 Wire Harness Connection
JEXTERIOR COMPONENTSÐYJ 23 - 127

REPLACEMENTÐXJ VEHICLES, DRIVE
AXLE ASSEMBLY; REAR SUSPENSION
AND AXLES......................3-14,3-31
REPLACEMENTÐXJ, WINDSHIELD
GLASS.............................23-69
REPLACEMENTÐYJ, BACK-UP/REAR
TURN SIGNAL/TAIL LAMP BULB.........8L-28
REPLACEMENTÐYJ, DOOR FRAME
GLASS CHANNEL...................23-142
REPLACEMENTÐYJ, DOOR
WEATHERSTRIP SEAL................23-142
REPLACEMENTÐYJ, DRL MODULE......8L-30
REPLACEMENTÐYJ, FOG LAMP.........8L-25
REPLACEMENTÐYJ, FOG LAMP SWITCH . 8L-26
REPLACEMENTÐYJ, FRONT PARK/TURN
SIGNAL LAMP BULB..................8L-25
REPLACEMENTÐYJ, HEADLAMP BULB . . . 8L-23
REPLACEMENTÐYJ, HEADLAMP
DIMMER SWITCH....................8L-26
REPLACEMENTÐYJ, LIFTGATE GLASS
WEATHERSTRIP SEAL................23-125
REPLACEMENTÐYJ, SIDE MARKER
LAMP BULB.........................8L-25
REPLACEMENTÐYJ, UNDERHOOD LAMP . 8L-29
REPLACEMENTÐYJ, UNDERHOOD LAMP
BULB..............................8L-29
REPLACEMENTÐYJ VEHICLES, DRIVE
AXLE ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-24
REPLACEMENTÐYJ VEHICLES, DRIVE
AXLE ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-14
REPLACEMENTÐYJ VEHICLES,
HARDTOP DOME/CARGO LAMP BULB....8L-31
REQUIREMENTS, FUEL..................0-1
REQUIRING NO LUBRICATION,
COMPONENTS.........................0-2
RESERVE/OVERFLOW SYSTEM,
COOLANT............................7-24
RESERVOIR REPLACEMENT (2-PIECE
MASTER CYLINDER)...................5-19
RESERVOIR, VACUUM.................8H-1
RESISTANCE, IGNITION COIL............8D-9
RESISTANCE (OHMS)ÐCOOLANT
TEMPERATURE SENSOR/MANIFOLD
AIR TEMPERATURE, SENSOR...........14-46
RESISTANCE, SPARK PLUG CABLE......8D-14
RESISTORS REPLACEMENT, BLOWER
MOTOR............................24-31
RESTRAINT REPLACEMENTÐXJ, DOOR . . . 23-41
RETAINER AND PISTON
SPECIFICATIONS, AW-4...............21-340
RETAINING BRACKETÐYJ, REARVIEW
MIRROR..........................23-144
RETURNÐPCM INPUT, SENSOR.........14-25
REVEAL MOLDINGÐXJ, WINDSHIELD....23-66
REVEAL MOLDINGÐYJ, WINDSHIELD . . . 23-144
RHD, STEERING.....................19-74
RIGHT HAND DRIVE, AUTOMATIC BELT
TENSIONERÐXJ MODELS WITH.........7-42
RIGHT HAND DRIVE, BELT SERVICEÐ
EXCEPT.............................7-40
RIGHT HAND DRIVE, BELT SERVICEÐXJ
MODELS WITH.......................7-42
RIGHT HAND DRIVE (RHD), BELT
TENSIONÐEXCEPT....................7-38
RIGHT HAND DRIVE (RHD) MODELS,
BELT TENSIONÐEXCEPT...............7-45
RIGHT HAND DRIVE VEHICLES...........23-1
RIGHT TURN RELAY; TRAILER TOW
(XJ).............................8W-54-1
RIGHT TURN RELAY; TRAILER TOW
(XJ-RHD).........................8W-54-1
RING CHARTÐAX 15 MANUAL
TRANSMISSION, SELECTIVE SNAP......21-334
RING/THRUST WASHER/THRUST PLATE
SPECIFICATIONS, 30RH/32RH SNAP.....21-335
ROCKER ARMS AND PUSH RODS....9-23,9-65
ROD AND PAWL SERVICE, PARK.......21-190
ROD BALL STUD REPLACEMENTÐXJ,
LIFTGATE SUPPORT
..................23-63
ROD BEARING FITTING CHART,
CONNECTING
.....................9-41,9-83
ROD CYLINDER DISPOSALÐXJ,
LIFTGATE SUPPORT
..................23-63
ROD CYLINDERÐXJ, LIFTGATE
SUPPORT
..........................23-62
ROD, TIE
......................19-16,19-19RODS, PISTONS AND CONNECTING . . . 9-39,9-81
RODS, ROCKER ARMS AND PUSH....9-23,9-65
RODSÐXJ, DOOR INSIDE LATCH
RELEASE AND LOCK..................23-50
ROOF VENTÐYJ, HARD TOP..........23-127
ROTOR, DISTRIBUTOR.................8D-8
ROTOR, IGNITION CABLES,
DISTRIBUTOR CAP....................0-20
ROTOR INSTALLATION.................5-51
ROTOR REFINISHING, DISC BRAKE.......5-53
ROTOR REMOVAL.....................5-51
ROTOR RUNOUT, DISC BRAKE...........5-52
ROTOR THICKNESS, DISC BRAKE........5-52
ROTORÐSPEEDOMETER DRIVE GEAR,
SPEED SENSOR.....................21-193
ROUGH AND/OR HAS A MISS, INJECTOR
DIAGNOSISÐVEHICLE RUNS...........14-52
ROUTING SCHEMATICÐ2.5L 4
CYLINDER ENGINE, VACUUM............25-3
ROUTING SCHEMATICÐ4.0L 6
CYLINDER ENGINE, VACUUM............25-3
ROUTING SCHEMATICS, VACUUM HOSE . . . 25-2
ROUTING, SYSTEM COOLANT.............7-1
RUBBER AND PLASTIC COMPONENT
INSPECTION.........................0-20
RUBBER AND PLASTIC HOSES/TUBING....0-26
RUNNING LAMP (DRL) MODULE,
DAYTIME.........................8W-50-2
RUNNING LAMP (DRL) MODULEÐ
CANADIAN VEHICLES ONLY, DAYTIME. . . 8W-50-2
RUNNING LIGHTS (CANADA ONLY)ÐXJ,
DAYTIME...........................8L-15
RUNNING LIGHTS (CANADA ONLY)ÐYJ,
DAYTIME...........................8L-30
RUNOUT............................16-4
RUNOUT, CLUTCH COVER AND DISC.......6-3
RUNOUT, DISC BRAKE ROTOR...........5-52
RUNOUT, FLYWHEEL....................6-3
RUNOUT SPECIFICATIONS..............16-4
RUNOUT, TIRE AND WHEEL.............22-8
RUNS ROUGH AND/OR HAS A MISS,
INJECTOR DIAGNOSISÐVEHICLE........14-52
SAFETY CERTIFICATION LABEL, VEHICLE . Intro.-4
SAFETY LATCH STRIKER
REPLACEMENTÐXJ..................23-11
SAFETY LATCHÐYJ, HOOD............23-109
SAFETY PRECAUTIONS AND WARNINGS . . 13-10
SAFETY PRECAUTIONS, BRAKE...........5-2
SAFETY PRECAUTIONS, CLUTCH.........6-10
SANDING,BUFFING AND POLISHING,
WET..............................23-158
SCAN TOOL, DRB; BRAKES...............5-3
SCAN TOOL, DRB; COOLING SYSTEM......7-5
SCAN TOOL, DRB; EMISSION CONTROL
SYSTEMS...........................25-2
SCAN TOOL, DRB; FUEL SYSTEM........14-54
SCAN TOOL, DRB; IGNITION SYSTEMS....8D-8
SCHEDULES, MAINTENANCE.............0-4
SCHEMATIC - YJ, BUZZER MODULE......8U-4
SCHEMATICÐ2.5L 4 CYLINDER ENGINE,
VACUUM ROUTING....................25-3
SCHEMATICÐ4.0L 6 CYLINDER ENGINE,
VACUUM ROUTING....................25-3
SCHEMATICÐXJ, AIR CONDITIONING.....24-5
SCHEMATICÐXJ, HEATING..............24-2
SCHEMATICS, BELT....................7-38
SCHEMATICS, PCM SYSTEM............14-41
SCHEMATICS, VACUUM HOSE ROUTING . . . 25-2
SCI RECEIVEÐPCM INPUT.............14-24
SCI TRANSMITÐPCM OUTPUT.........14-29
SCREENÐXJ, COWL GRILLE...........23-12
SCREENÐXJ, HEADLAMP/FOG LAMP
ADJUSTMENT USING ALIGNMENT........8L-7
SCREENÐYJ, COWL GRILLE..........23-109
SCREENÐYJ, HEADLAMP/FOG LAMP
ADJUSTMENT USING ALIGNMENT.......8L-23
SCREW ANCHOR AND BUMPERÐXJ,
LIFTGATE LICENSE PLATE..............23-65
SCUFF PLATE/COWL SIDE TRIM
PANELÐXJ, FRONT INNER.............23-86
SCUFF PLATESÐXJ, INTERIOR TRIM
PANELS
............................23-84
SCUFF PLATESÐXJ, OUTER
............23-89
SEAL AND BEARING, AXLE SHAFT
........3-17
SEAL AND BEARING SERVICE, AXLE
SHAFT
..............................3-32
SEAL AND SPRING REPLACEMENT,
VALVE STEM
.........................9-65SEAL REPLACEMENT, INNER AXLE
SHAFT OIL...........................2-35
SEAL REPLACEMENT, MANUAL VALVE
SHAFT............................21-187
SEAL REPLACEMENT, OIL PUMP.......21-199
SEAL REPLACEMENT, PINION; FRONT
SUSPENSION AND AXLE................2-25
SEAL REPLACEMENT, PINION; REAR
SUSPENSION AND AXLES...............3-33
SEAL REPLACEMENT, PINION SHAFT......3-15
SEAL REPLACEMENT, PITMAN SHAFT....19-37
SEAL REPLACEMENT, TIMING CASE
COVER OIL......................9-30,9-73
SEAL REPLACEMENTÐYJ, DOOR
WEATHERSTRIP....................23-142
SEAL REPLACEMENTÐYJ, LIFTGATE
GLASS WEATHERSTRIP..............23-125
SEAL/CROSSMEMBER AIR
DEFLECTORÐXJ, COWL
WEATHERSTRIP.....................23-11
SEALÐDRIVE PLATE SERVICE,
CONVERTERÐPUMP.................21-116
SEALÐXJ, LIFTGATE OPENING
WEATHERSTRIP.....................23-64
SEALÐYJ, BELTLINE.................23-142
SEALÐYJ, COWL WEATHERSTRIP......23-109
SEALÐYJ, TAILGATE WEATHERSTRIP . . . 23-123
SEALÐYJ, WINDSHIELD FRAME
WEATHERSTRIP....................23-146
SEALS AND BEARING REPLACEMENT,
PITMAN SHAFT......................19-34
SEALS, REAR MAIN OIL..............9-49,9-89
SEALS, VALVE SPRINGS AND OIL........9-23
SEALSÐIN CAR REPLACEMENT, PITMAN
SHAFT.............................19-23
SEALSÐXJ, DOOR WINDOW GLASS
AND DOOR OPENING WEATHERSTRIP....23-55
SEALSÐYJ, FULL-METAL DOOR
WEATHERSTRIP....................23-141
SEAT ADJUSTER/MOTORS, POWER . . . 8R-1,8R-2
SEAT ADJUSTER/MOTORS REMOVE/
INSTALL, POWER.....................8R-3
SEAT BELT INDICATOR WARNING LAMP;
INSTRUMENT CLUSTER (XJ).........8W-40-2
SEAT BELT INDICATOR WARNING LAMP;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
SEAT BELT SWITCH, DRIVER'S......8U-1,8U-3
SEAT CUSHION AND COVERÐXJ,
BUCKET............................23-81
SEAT CUSHION COVERÐXJ, REAR......23-82
SEAT CUSHIONÐXJ, REAR.............23-82
SEAT PLATFORMÐXJ, BUCKET.........23-82
SEAT, POWER; POWER SEAT (XJ).....8W-63-1
SEAT, POWER; POWER SEAT (XJ-RHD) . 8W-63-1
SEAT SWITCH CONTINUITY, POWER......8R-2
SEAT SWITCH, POWER............8R-1,8R-2
SEAT SWITCH REMOVE/INSTALL,
POWER.............................8R-3
SEATBACK COVER AND FRAMEÐXJ,
BUCKET............................23-81
SEATBACK COVERÐXJ, REAR..........23-84
SEATBACK LATCH STRIKER AND
BUMPERÐXJ, REAR..................23-84
SEATBACKÐXJ, REAR................23-83
SEATÐYJ, REAR BENCH..............23-153
SEATSÐXJ, FRONT BUCKET............23-81
SEATSÐYJ........................23-153
SEATSÐYJ, BUCKET.................23-153
SECOND (2) RANGE, HYDRAULIC FLOW
IN MANUAL.........................21-96
SECOND BRAKE OVERHAUL...........21-241
SECONDARY CABLES, SPARK PLUG.....8D-14,
8D-24
SECONDARY CIRCUIT DIAGNOSIS,
IGNITION...........................8D-10
SECTION IDENTIFICATION; WIRING
DIAGRAMS (XJ)......................8W-1
SECTION IDENTIFICATION; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
SECTION IDENTIFICATION; WIRING
DIAGRAMS (YJ)
......................8W-1
SELECTIVE SNAP RING CHARTÐAX 15
MANUAL TRANSMISSION
.............21-334
SELF-DIAGNOSTIC TEST, COMPASS/
DISPLAY
............................8C-2
SENDING UNIT, FUEL GAUGE
...........14-16
SENSEÐPCM INPUT, AUTOMATIC
SHUTDOWN (ASD)
...................14-21
24 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

TIRE/WHEEL HOLDDOWN AND FLOOR
BRACKETSÐXJ, SPARE...............23-98
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ)......................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (YJ)......................8W-1
TOOL, DRB SCAN; BRAKES...............5-3
TOOL, DRB SCAN; COOLING SYSTEM......7-5
TOOL, DRB SCAN; EMISSION CONTROL
SYSTEMS...........................25-2
TOOL, DRB SCAN; FUEL SYSTEM........14-54
TOOL, DRB SCAN; IGNITION SYSTEMS....8D-8
TOOLS, TROUBLESHOOTING............8W-4
TOP DOORÐYJ, HALF-METAL SOFT.....23-134
TOP LIFTGATE GLASSÐYJ, HARD......23-124
TOP QUARTER WINDOW GLASSÐYJ,
HARD.............................23-149
TOP REPAIRÐYJ, HARD..............23-127
TOP ROOF VENTÐYJ, HARD..........23-127
TOP SERVICE INFORMATIONÐYJ, SOFT . 23-127
TOP SERVICEÐYJ, SOFT.............23-129
TOPÐYJ, HARD....................23-126
TORQUE; BATTERY/STARTER/
GENERATOR SERVICE..................8B-8
TORQUE; COOLING SYSTEM.............7-46
TORQUE; FUEL SYSTEM...............14-67
TORQUE; IGNITION SYSTEMS............8D-32
TORQUE CONVERTER...........21-167,21-67
TORQUE CONVERTER CLUTCH RELAY....14-65
TORQUE CONVERTER CLUTCH RELAY
TEST..............................14-48
TORQUE CONVERTER CLUTCH
RELAYÐPCM OUTPUT................14-29
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY; FUEL/IGNITION
(XJ).............................8W-30-4
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY;
TRANSMISSION CONTROLS (YJ)......8W-31-1
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAYÐ2.5L ENGINE
ONLY; TRANSMISSION CONTROLS (XJ) . 8W-31-1
TORQUE CONVERTER DIAGNOSIS . . 21-86,21-87,
21-88
TORQUE CONVERTER INSTALLATION,
TRANSMISSION.....................21-199
TORQUE CONVERTER REMOVAL,
TRANSMISSION.....................21-198
TORQUE CONVERTER STALL TEST......21-178
TORQUE CONVERTER STATOR CLUTCH
INSPECTION.......................21-199
TORQUE SPECIFICATIONS; CLUTCH.......6-17
TORQUE SPECIFICATIONS; ENGINES . . 9-54,9-95
TORQUE SPECIFICATIONS; EXHAUST
SYSTEM AND INTAKE MANIFOLD........11-10
TORQUE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE................2-49
TORQUE SPECIFICATIONS; HEATING AND
AIR CONDITIONING...................24-37
TORQUE SPECIFICATIONS;
INTRODUCTION............Intro.-11,Intro.-12
TORQUE SPECIFICATIONS; PROPELLER
SHAFTS............................16-15
TORQUE SPECIFICATIONS; REAR
SUSPENSION AND AXLES...............3-51
TORQUE SPECIFICATIONS; STEERING....19-78
TORQUE SPECIFICATIONS, 30RH/32RH . . 21-336
TORQUE SPECIFICATIONS, AW-4.......21-344
TORQUE SPECIFICATIONS, BRAKE........5-70
TORQUE SPECIFICATIONS,
MEASUREMENT...................Intro.-11
TORQUE SPECIFICATIONS, NP231/NP242 . 21-344
TORQUE SPECIFICATIONSÐ
ACCESSORIES......................23-162
TORQUE SPECIFICATIONSÐMANUAL
TRANSMISSION.....................21-333
TORQUE SPECIFICATIONSÐXJ
VEHICLES.........................23-161
TORQUEÐ2.5L.......................8B-8
TORQUEÐ4.0L.......................8B-8
TOUCH-UP, PAINTED SURFACE.........23-158
TOW HOOK, REAR
.....................13-9
TOW HOOKS
........................13-13
TOW HOOKS, FRONT
..................13-7
TOW, TRAILER; TRAILER TOW (XJ)
....8W-54-1
TOW, TRAILER; TRAILER TOW (XJ-RHD)
. 8W-54-1TOWING AND HOISTING, JUMP
STARTING............................0-9
TOWING, FOUR-WHEEL-DRIVE VEHICLE . . . 0-12
TOWING RECOMMENDATIONS...........0-10
TOWING SPECIFICATIONS, TRAILER....Intro.-5,
Intro.-9
TOWING WHEN KEYS ARE NOT
AVAILABLE..........................0-13
TOWINGÐXJ, TWO-WHEEL-DRIVE
VEHICLE............................0-11
(TPS)ÐPCM INPUT, THROTTLE
POSITION SENSOR...................14-25
TRACK BAR; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
TRACK BAR; REAR SUSPENSION AND
AXLES...............................3-8
TRAC-LOK DIFFERENTIAL...............3-45
TRAILER HITCH......................23-77
TRAILER HITCHÐXJ..................23-77
TRAILER TOW; TRAILER TOW (XJ)....8W-54-1
TRAILER TOW; TRAILER TOW (XJ-RHD) . 8W-54-1
TRAILER TOWING SPECIFICATIONS....Intro.-5,
Intro.-9
TRANSFER CASE (4WD VEHICLES).......0-24
TRANSFER CASE ASSEMBLY....21-294,21-319
TRANSFER CASE CHANGES...........21-307
TRANSFER CASE DISASSEMBLY AND
OVERHAUL..................21-289,21-310
TRANSFER CASE IDENTIFICATION......21-284,
21-307
TRANSFER CASE INSTALLATION . . 21-288,21-309
TRANSFER CASE, LEGEND FOR NP231 . . 21-306
TRANSFER CASE, LEGEND FOR NP242 . . 21-332
TRANSFER CASE LUBRICANT AND FILL
LEVEL............................21-284
TRANSFER CASE, NP231.......21-283,21-305
TRANSFER CASE, NP242.......21-307,21-331
TRANSFER CASE REMOVAL.....21-287,21-309
TRANSFER CASE SKID PLATE.......13-15,13-3
TRANSMISSION, 30RH/32RH
AUTOMATIC.........................21-67
TRANSMISSION AND CONVERTER
INSTALLATION......................21-117
TRANSMISSION AND CONVERTER
REMOVAL.........................21-115
TRANSMISSION AND TORQUE
CONVERTER INSTALLATION...........21-199
TRANSMISSION AND TORQUE
CONVERTER REMOVAL...............21-198
TRANSMISSION APPLICATION..........21-67
TRANSMISSION ASSEMBLY AND
ADJUSTMENT............21-265,21-16,21-52
TRANSMISSION ASSEMBLY AND
ADJUSTMENT PROCEDURES..........21-155
TRANSMISSION ASSEMBLY TIPS.......21-155
TRANSMISSION, AUTOMATIC............0-23
TRANSMISSION, AW-4 AUTOMATIC.....21-165
TRANSMISSION, AX 15 MANUAL........21-33
TRANSMISSION, AX 4/5 MANUAL........21-1
TRANSMISSION CASE CLEANING AND
INSPECTION.......................21-125
TRANSMISSION CASE OVERHAUL,
FIRST-REVERSE BRAKE PISTON........21-247
TRANSMISSION CHANGES AND PARTS
INTERCHANGEABILITY................21-67
TRANSMISSION COMFORT SWITCH;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE
(TCM) SERVICE.....................21-183
TRANSMISSION CONTROL MODULEÐ
4.0L ENGINE ONLY; TRANSMISSION
CONTROLS (XJ)...................8W-31-1
TRANSMISSION CONTROLS AND
COMPONENTS.......................21-67
TRANSMISSION COOLER FLOW TESTING . 21-113
TRANSMISSION COOLER LINE AND
FITTING SERVICE...................21-111
TRANSMISSION COOLER LINE FITTINGS . 21-197
TRANSMISSION COOLER REVERSE
FLUSHING.........................21-114
TRANSMISSION COOLER SERVICE
......21-196
TRANSMISSION DIAGNOSIS
. 21-78,21-79,21-80,
21-81,21-82,21-83,21-84,21-85
TRANSMISSION DIAGNOSIS, 30RH/32RH
. 21-70
TRANSMISSION DIAGNOSIS, AW-4
.....21-176
TRANSMISSION DISASSEMBLY
. . 21-119,21-201TRANSMISSION DISASSEMBLY AND
OVERHAUL.....................21-37,21-5
TRANSMISSION GEAR RATIOS..........21-34
TRANSMISSION IDENTIFICATION . . 21-166,21-33,
21-67,21-2
TRANSMISSION INSTALLATION.....21-36,21-5
TRANSMISSION LUBRICANT............21-34
TRANSMISSION, MANUAL..............0-22
TRANSMISSION OIL COOLERS...........7-36
TRANSMISSION OVERHAUL, 30RH/32RH . 21-119
TRANSMISSION OVERHAUL, AW-4......21-201
TRANSMISSION RANGE LAMP;
INTERIOR LIGHTING (YJ)............8W-44-1
TRANSMISSION RANGES AND SHIFT
LEVER POSITIONS...................21-166
TRANSMISSION REMOVAL.........21-35,21-3
TRANSMISSION REMOVAL AND
INSTALLATION, 30RH/32RH...........21-115
TRANSMISSION REMOVAL AND
INSTALLATION, AW-4................21-198
TRANSMISSION SHIFT PATTERN........21-34
TRANSMISSION SHIFTER/IGNITION
INTERLOCK MECHANISM, AUTOMATIC....19-55
TRANSMISSION SWITCH AND PLUG
LOCATIONS.........................21-34
TRANSMISSION THROTTLE CABLE
ADJUSTMENT......................21-194
TRANSMISSION THROTTLE CABLE
REPLACEMENT.....................21-193
TRANSMISSION THROTTLE VALVE
CABLE ADJUSTMENT...................21-71
TRANSMISSION, TORQUE
SPECIFICATIONSÐMANUAL...........21-333
TRANSMISSION UP-SHIFT LAMP,
MANUAL; INSTRUMENT CLUSTER (XJ) . 8W-40-2
TRANSMISSION VALVE BODY
INSTALLATION......................21-187
TRANSMISSION VALVE BODY
OVERHAUL........................21-250
TRANSMISSION VALVE BODY REMOVAL . 21-186
TRANSMISSION VALVE BODY
SOLENOIDS........................21-184
TRANSMISSION/TRANSFER CASE
IDENTIFICATION, ENGINE.............Intro.-5
TRANSMISSION/TRANSFER CASE
SPECIFICATIONS....................21-333
TRANSMITÐPCM OUTPUT, SCI.........14-29
TRANSMITTER, KEYLESS ENTRY . 8P-1,8P-7,8P-8
TRAVEL SENSOR, BRAKE PEDAL;
ANTI-LOCK BRAKES (YJ)............8W-32-1
TRAY LAMPÐXJ, I/P ASH RECEIVER.....23-80
TRAYÐXJ, BATTERY
..................23-14
TRAYÐYJ, BATTERY
.................23-110
TREAD WEAR INDICATORS
..............22-3
TRIM COVERSÐXJ, B/C-PILLAR AND
LIFTGATE PILLAR
....................23-88
TRIM PANEL EXTENSIONÐXJ, QUARTER
. 23-87
TRIM PANELÐXJ, DOOR
..............23-31
TRIM PANELÐXJ, FRONT INNER SCUFF
PLATE/COWL SIDE
...................23-86
TRIM PANELÐXJ, LIFTGATE
............23-59
TRIM PANELÐYJ, FULL-METAL DOOR
. . . 23-137
TRIM PANELS AND SCUFF PLATESÐXJ,
INTERIOR
..........................23-84
TRIM PANELSÐXJ, QUARTER AND
WHEELHOUSE
.......................23-87
TRIM REPAIR PRODUCTSÐXJ,
AFTERMARKET PAINT
................23-159
TRIM REPAIR PRODUCTSÐYJ,
AFTERMARKET PAINT
................23-160
TROUBLE CODE (DTC), DIAGNOSTIC
.....14-54
TROUBLE CODE, GENERATOR
DIAGNOSTIC
........................8A-22
TROUBLE CODE, SPEED CONTROL
DIAGNOSTIC
.........................8H-5
TROUBLE DIAGNOSISÐXJ, DOME/
COURTESY LAMP
....................8L-16
TROUBLE DIAGNOSISÐXJ, HEADLAMP
DELAY FUNCTION
....................8L-14
TROUBLE DIAGNOSISÐXJ, LIGHTED
VANITY MIRROR
.....................8L-16
TROUBLE DIAGNOSISÐYJ, DOME/
COURTESY LAMP
....................8L-31
TROUBLESHOOTING TESTS; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)
...............................8W-4
30 INDEXJ
Description Group-Page Description Group-Page Description Group-Page