1995 JEEP CHEROKEE parking brake

TAILGATE LATCH STRIKERÐYJ........23-123
TAILGATE LOCK CYLINDERÐYJ........23-122
TAILGATE WEATHERSTRIP SEALÐYJ....23-123
TAILGATEÐYJ......................23-121
TAILPIPEÐXJ VEHICLES, MUFFLER AND
EXHAUST............................11-5
TAILPIPEÐYJ VEHICLES, MUFFLER AND
EXHAUST............................11-6
TAKE OUTS; WIRING DIAGRAMSÐ
GENERAL INFORMATION (XJ)...........8W-2
TANK CAPACITIES, FUEL..........14-13,14-67
TANK FILLER TUBE CAP, FUEL;
EMISSION CONTROL SYSTEMS......25-4,25-7
TANK FILLER TUBE CAP, FUEL; FUEL
SYSTEM............................14-13
TANK FILLER TUBE, NO-LEAD FUEL......14-13
TANK, FUEL.........................14-13
TANK PRESSURE RELIEF/ROLLOVER
VALVE, FUEL...................14-16,14-62
TANK SKID PLATE, FUEL...........13-15,13-3
TANK SUPPORT STRAP, FUEL............13-4
TANKS, FUEL...................14-13,14-62
TAPPETS, HYDRAULIC.............9-24,9-66
TELL-TALE CLUSTER (LHD)............8E-10
TEMPERATURE AND PRESSURE CHART,
XJ PERFORMANCE...................24-13
TEMPERATURE AND PRESSURE CHART,
YJ PERFORMANCE...................24-13
TEMPERATURE CONTROL THERMOSTAT . . 24-34
TEMPERATURE GAUGE, ENGINE
COOLANT; INSTRUMENT CLUSTER
(XJ).............................8W-40-1
TEMPERATURE SENSOR, COOLANT.......25-7
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL SYSTEM..............14-60
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL/IGNITION (XJ).......8W-30-3
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL/IGNITION (YJ).......8W-30-3
TEMPERATURE SENSOR, ENGINE
COOLANT; IGNITION SYSTEMS.....8D-19,8D-5
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL/IGNITION (XJ-RHD) . . . 8W-30-3
TEMPERATURE SENSOR, INTAKE AIR;
FUEL/IGNITION (XJ)................8W-30-4
TEMPERATURE SENSOR, INTAKE AIR;
FUEL/IGNITION (YJ)................8W-30-4
TEMPERATURE SENSOR, INTAKE AIR;
FUEL/IGNITION (XJ-RHD)............8W-30-4
TEMPERATURE SENSOR, INTAKE
MANIFOLD AIR; FUEL SYSTEM..........14-60
TEMPERATURE SENSOR, INTAKE
MANIFOLD AIR; IGNITION SYSTEMS . 8D-23,8D-5
TEMPERATURE, SENSOR RESISTANCE
(OHMS)ÐCOOLANT TEMPERATURE
SENSOR/MANIFOLD AIR...............14-46
TEMPERATURE SENSOR TEST, ENGINE
COOLANT; FUEL SYSTEM..............14-46
TEMPERATURE SENSOR TEST, ENGINE
COOLANT; IGNITION SYSTEMS..........8D-9
TEMPERATURE SENSOR TEST, INTAKE
MANIFOLD AIR; FUEL SYSTEM
..........14-46
TEMPERATURE SENSOR TEST, INTAKE
MANIFOLD AIR; IGNITION SYSTEMS
.....8D-11
TEMPERATURE SENSOR/MANIFOLD AIR
TEMPERATURE, SENSOR RESISTANCE
(OHMS)ÐCOOLANT
..................14-46
TEMPERATURE SENSORÐPCM INPUT,
ENGINE COOLANT
....................14-23
TEMPERATURE SENSORÐPCM INPUT,
INTAKE MANIFOLD AIR
................14-22
TEMPERATURE WARNING LAMP, ENGINE
COOLANT; INSTRUMENT CLUSTER
(XJ)
.............................8W-40-1
TEMPERATURE WARNING LAMP, ENGINE
COOLANT; INSTRUMENT CLUSTER
(XJ-RHD)
.........................8W-40-1
TENSION, DRIVE BELT
.................7-45
TENSION SPECIFICATIONS, BELT
.........7-38
TENSIONER ADJUSTMENT (XJ/YJ),
PARKING BRAKE CABLE
................5-69
TENSIONER REPLACEMENT (XJ),
PARKING BRAKE CABLE
................5-66
TENSIONERÐXJ MODELS WITH RIGHT
HAND DRIVE, AUTOMATIC BELT
..........7-42
TENSIONÐEXCEPT RIGHT HAND DRIVE
(RHD), BELT
.........................7-38TENSIONÐEXCEPT RIGHT HAND DRIVE
(RHD) MODELS, BELT..................7-45
TENSIONÐRIGHT HAND DRIVE (RHD),
BELT ...............................7-38
TERMINAL REPLACEMENT; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-8
TERMINAL REPLACEMENT, CONNECTOR;
WIRING DIAGRAMSÐGENERAL
INFORMATION (XJ)...................8W-7
TERMINAL/CONNECTOR REPAIRÐ
MOLEX CONNECTORS; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-6
TEST, AUTOMATIC SHUTDOWN (ASD)
RELAY..............................8D-6
TEST, CAMSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-46
TEST, CAMSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-6
TEST, COMPASS/DISPLAY SELF-
DIAGNOSTIC.........................8C-2
TEST, CONVERTER STALL..............21-74
TEST, CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-47
TEST, CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-7
TEST, CYLINDER COMBUSTION
PRESSURE LEAKAGE...................9-6
TEST, CYLINDER COMPRESSION
PRESSURE...........................9-5
TEST DIAGNOSIS, CYLINDER
COMBUSTION PRESSURE LEAKAGE........9-7
TEST, ENGINE COOLANT TEMPERATURE
SENSOR; FUEL SYSTEM................14-46
TEST, ENGINE COOLANT TEMPERATURE
SENSOR; IGNITION SYSTEMS...........8D-9
TEST, EXTENDED IDLE SWITCH.........14-48
TEST, FUEL INJECTOR.................14-51
TEST, FUEL PRESSURE LEAK DOWN......14-8
TEST, FUEL PUMP CAPACITY............14-7
TEST, FUEL SYSTEM PRESSURE....14-51,14-6
TEST, HYDRAULIC PRESSURE....21-177,21-72
TEST, IDLE AIR CONTROL MOTOR.......14-49
TEST, INTAKE MANIFOLD AIR
TEMPERATURE SENSOR; FUEL
SYSTEM............................14-46
TEST, INTAKE MANIFOLD AIR
TEMPERATURE SENSOR; IGNITION
SYSTEMS..........................8D-11
TEST, MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR; FUEL SYSTEM.........14-47
TEST, MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR; IGNITION SYSTEMS.....8D-11
TEST, MANUAL SHIFTING.............21-177
TEST, MASTER CYLINDER/POWER
BOOSTER............................5-8
TEST, OXYGEN SENSOR (O2S) HEATING
ELEMENT...........................14-48
TEST, POWER BOOSTER CHECK VALVE.....5-9
TEST, POWER BOOSTER VACUUM.........5-9
TEST PROCEDURES, HEATING AND AIR
CONDITIONING......................24-15
TEST, REFRIGERANT SERVICE AND
PERFORMANCE......................24-11
TEST, STARTER MOTOR RELAY.........14-51
TEST, THROTTLE POSITION SENSOR.....8D-15
TEST, THROTTLE POSITION SENSOR
(TPS)..............................14-48
TEST, TORQUE CONVERTER CLUTCH
RELAY
.............................14-48
TEST, TORQUE CONVERTER STALL
.....21-178
TEST, VACUUM SUPPLY
................8H-6
TEST, VEHICLE SPEED SENSOR
.........14-48
TESTING, AUTOMATIC SHUTDOWN
(ASD) RELAY
........................14-46
TESTING COOLING SYSTEM FOR LEAKS
. . . 7-22
TESTING, FUEL PUMP RELAY
...........14-47
TESTING, INTERMITTENT WIPE SWITCH
. . 8K-15
TESTING, NON-INTERMITTENT WIPE
SWITCH
............................8K-14
TESTING PROCEDURESÐXJ, MULTI-
FUNCTION SWITCH
....................8L-4
TESTING REFRIGERANT, LEAK
..........24-11
TESTING, ROAD
.......................5-5
TESTING SPECIFICATIONS, 2.5L
STARTER AND SOLENOID
..............8A-23TESTING SPECIFICATIONS, 4.0L
STARTER AND SOLENOID..............8A-23
TESTING, TRANSMISSION COOLER
FLOW.............................21-113
TESTS, AIR CONDITIONING
PERFORMANCE......................24-12
TESTS, IGNITION SWITCH CONTINUITY . . . 8D-30
TESTS, OXYGEN (O2S) SENSOR........8D-15
TESTS, SYSTEM......................8N-1
TESTS, TROUBLESHOOTING; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-4
TESTS, WATER PUMP..................7-13
THERMOMETER......................8C-1
THERMOMETER DIAGNOSIS.............8C-2
THERMOSTAT........................7-17
THERMOSTAT, TEMPERATURE CONTROL . . 24-34
THERMOSTATIC CONTROL.............24-16
THICKNESS, AW-4 CLUTCH DISC AND
PLATE ............................21-338
THICKNESS, DISC BRAKE ROTOR........5-52
THIS GROUP, HOW TO USE; WIRING
DIAGRAMS (XJ)......................8W-1
THIS GROUP, HOW TO USE; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
THIS GROUP, HOW TO USE; WIRING
DIAGRAMS (YJ)......................8W-1
THREAD NOTATIONÐSAE AND METRIC . Intro.-13
THREADS, REPAIR DAMAGED OR WORN....9-4
THROTTLE BODY.................14-33,14-64
THROTTLE CABLE....................14-17
THROTTLE CABLE, ACCELERATOR
PEDAL........................14-17,14-58
THROTTLE CABLE ADJUSTMENT,
TRANSMISSION.....................21-194
THROTTLE CABLE REPLACEMENT,
TRANSMISSION.....................21-193
THROTTLE POSITION SENSOR;
FUEL/IGNITION (XJ)................8W-30-4
THROTTLE POSITION SENSOR;
FUEL/IGNITION (YJ)................8W-30-4
THROTTLE POSITION SENSOR; IGNITION
SYSTEMS...........................8D-5
THROTTLE POSITION SENSOR;
FUEL/IGNITION (XJ-RHD)............8W-30-4
THROTTLE POSITION SENSOR TEST.....8D-15
THROTTLE POSITION SENSOR (TPS);
FUEL SYSTEM.......................14-65
THROTTLE POSITION SENSOR (TPS);
IGNITION SYSTEMS..................8D-25
THROTTLE POSITION SENSOR (TPS)
SERVICE..........................21-193
THROTTLE POSITION SENSOR (TPS)
TEST..............................14-48
THROTTLE POSITION SENSOR
(TPS)ÐPCM INPUT...................14-25
THROTTLE VALVE CABLE ADJUSTMENT,
TRANSMISSION......................21-71
THROTTLE VALVE CABLE ADJUSTMENT
(XJ/YJ)............................21-101
THROUGH DEEP WATER PUDDLES,
BRAKES DO NOT HOLD AFTER
DRIVING.............................5-7
TIE ROD ......................19-16,19-19
TIGHTENING, WHEEL NUT..........5-54,5-59
TILT STEERING COLUMN..............19-66
TIME LAG TEST.....................21-178
TIME TABLE, BATTERY CHARGING........8A-8
TIMING CASE COVER..............9-31,9-72
TIMING CASE COVER OIL SEAL
REPLACEMENT...................9-30,9-73
TIMING CHAIN AND SPROCKETS.....9-31,9-73
TIMING, IGNITION....................8D-11
TIMING, VALVE...................9-30,9-71
TIPS, TRANSMISSION ASSEMBLY......21-155
TIRE AND WHEEL BALANCE.............22-6
TIRE AND WHEEL RUNOUT.............22-8
TIRE CARRIERÐYJ, EXTERNAL
SPARE/WHEEL......................23-133
TIRE INFLATION PRESSURES............22-2
TIRE NOISE OR VIBRATION.............22-4
TIRE PROBLEMS, WHEEL................5-7
TIRE WEAR PATTERNS
.................22-4
TIRES; LUBRICATION AND
MAINTENANCE
.......................0-32
TIRES; WHEELS AND TIRES
.............22-1
TIRES, CLEANING OF
..................22-2
TIRES, REPLACEMENT
.................22-2
JINDEX 29
Description Group-Page Description Group-Page Description Group-Page

FUEL/IGNITION
INDEX
page page
Automatic Shut Down (ASD) Relay............. 1
Battery Feed.............................. 2
Brake Switch Input......................... 5
Camshaft Position Sensor.................... 3
Crankshaft Position Sensor................... 3
Data Link Connector........................ 5
Diagram Index............................ 5
Engine Coolant Temperature Sensor............ 3
Fuel Injectors............................. 2
Fuel Pump Module......................... 2
Fuel Pump Relay.......................... 2
Heated Oxygen Sensor...................... 3Idle Air Control (IAC) Motor................... 2
Ignition Coil.............................. 2
Ignition Switch............................ 1
Intake Air Temperature Sensor................ 4
Malfunction Indicator Lamp (MIL)............... 5
Manifold Absolute Pressure Sensor............. 4
Park/Neutral Position Switch.................. 4
Power (Device) Ground...................... 5
Power Steering Pressure Switch............... 4
Tachometer Signal......................... 5
Throttle Position Sensor..................... 4
Vehicle Speed Sensor....................... 3
IGNITION SWITCH
Circuit A1 from fuse 4 in the Power Distribution
Center (PDC), supplies battery voltage to the ignition
switch. Depending upon position, the ignition switch
powers circuits A21, A22, A31, and A41.
START POSITION
In the START position, the ignition switch connects
circuit A1 to circuit A41. Circuit A41 connects to the
coil side of the starter motor relay.
Also in the START position, the case grounded ig-
nition switch provides ground for the brake lamp
switch and parking brake lamp switch on circuit G11.
START OR RUN POSITION
In the START and RUN position, the ignition
switch connects circuit A1 with circuit A21. The A21
circuit connects to fuses 5 and 9 in the fuse block.
Fuse 9 powers circuit G5. Fuse 5 powers circuit G50.
²Circuit G5 powers the buzzer module. Circuit G5
also splices to power the daytime running lamps
module (Canada only), A/C compressor clutch relay,
heated rear window relay, and the gauges and indi-
cator lamps in the instrument cluster.
RUN (ONLY) POSITION
When the ignition switch is in the RUN position, it
connects circuit A1 to circuit A22. Circuit A22 powers
fuses 1, 12, and 13 in the fuse block.
²Fuse 1 powers the rear wiper system on circuit
V23.
²Fuse 12 feeds the blower motor and air condition-
ing system on circuit C1.
²Fuse 13 feeds circuit F15 which powers the ABS
module and connects to the coil side of the ABS
power relay.
ACCESSORY OR RUN POSITION
In the ACCESSORY or RUN position, the ignition
switch connects circuit A1 to circuit A31. Circuit A31
connects to a bus bar in the fuse block that feeds
fuses 4 and 7 along with the circuit breaker in cavity
11 .
²Fuse 4 powers circuit L5 which feeds the turn sig-
nal flasher.
²Fuse 7 powers circuit F30. Circuit F30 supplies
power to the radio, radio relay, and the cigar lighter.
²The circuit breaker in cavity 11 powers the V6 cir-
cuits which feed the wiper switch and wiper motor.
AUTOMATIC SHUT DOWN (ASD) RELAY
When the ignition switch is in either the START or
RUN position, it connects circuit A1 from fuse 4 in
the Power Distribution Center (PDC) to circuit A21.
Circuit A21 powers fuse 5 in the fuse block. Circuit
G50 from fuse 5 splices to power the coil side of the
Automatic Shut Down (ASD) relay. The Powertrain
Control Module (PCM) provides ground for the relay
on circuit K51. Circuit K51 connects to cavity 51 of
the PCM.
When the PCM grounds the ASD relay, contacts in-
side the relay close and connect circuit A14 from fuse
1 in the PDC to circuit A142. Circuit A142 splices to
the generator field terminal, fuel injectors, ignition
coil, and heated oxygen sensor. Circuit A142 also con-
nects to cavity 57 of the PCM.
Circuit A14 from fuse 1 in the PDC supplies bat-
tery voltage to the contact side of the ASD relay.
HELPFUL INFORMATION
²Along with supplying voltage to the ASD relay
contacts, circuit A14 supplies voltage to the contact
side of the fuel pump relay.
²Circuit G50 also supplies battery voltage to the
coil side of the fuel pump relay.
²Circuit A14 also connects to cavity 3 of the PCM.
J8W-30 FUEL/IGNITIONÐYJ VEHICLES 8W - 30 - 1

switch to ground on circuit Z1. The switch closes dur-
ing periods of high power steering pump load and
low engine speed; such as parking maneuvers. Cir-
cuit K10 connects to cavity 10 of the PCM.
TACHOMETER SIGNAL
The Powertrain Control Module (PCM) supplies the
signal for the tachometer on circuit G21. Circuit G21
connects to cavity 43 of the PCM.
MALFUNCTION INDICATOR LAMP (MIL)
The Powertrain Control Module (PCM) provides
ground for the instrument cluster malfunction indica-
tor lamp on circuit G3. The MIL displays the mes-
sage CHECK ENGINE when illuminated. Circuit G5
provides voltage for the lamp.
DATA LINK CONNECTOR
Circuit G50 supplies battery voltage to the data
link connector. Circuit G50 originates at fuse 5 in the
fuse block. Circuit G50 is double crimped at the data
link connector and connects to cavity 9 of the Power-
train Control Module (PCM).
Circuit A21 from the ignition switch powers fuse 5
when the switch is in the START or RUN positions.
In the START or RUN position the ignition switch
connects circuit A1 from fuse 4 in the Power Distri-
bution Center (PDC) with circuit A21.
Circuit D20 connects to cavity 45 of the PCM. Cir-
cuit D20 is the SCI receive circuit for the PCM.
Circuit D21 connects to cavity 25 of the PCM. Cir-
cuit D21 is the SCI transmit circuit for the PCM.
Circuit Z11 provides ground for the data link con-
nector. Circuit Z11 splices to circuit Z1 which termi-
nates at the right rear of the engine. Circuit Z11 also
connects to cavity 5 of the PCM.
HELPFUL INFORMATION
²Circuit Z1 also supplies a ground for the PCM
high current drivers.
²If the system loses ground for the Z1 and Z11 cir-
cuits at the right rear of the engine, the vehicle will
not operate. Check the connection at the ganged-
ground circuit eyelet.
BRAKE SWITCH INPUT
Circuit V40 provides the brake switch input to the
Powertrain Control Module (PCM). Circuit V40 con-
nects to cavity 29 of the PCM.
POWER (DEVICE) GROUND
Circuit Z11 connects to cavities 11 and 12 of the
Powertrain Control Module (PCM). The Z1 circuit
provides ground for PCM internal drivers that oper-
ate high current devices like the injectors and igni-
tion coil.
Internal to the PCM, the power (device) ground cir-
cuit connects to the PCM sensor return circuit (from
circuit K4).
HELPFUL INFORMATION
²The grounding point for circuit Z1 is the right rear
of the engine.
²If the system loses ground for the Z1 circuits at
the rear of the engine, the vehicle will not operate.
Check the connection at the ganged-ground circuit
eyelet.
DIAGRAM INDEX
Component Page
Automatic Shut Down Relay...............8W-30-6, 14
Camshaft Position Sensor................8W-30-10, 16
Crankshaft Position Sensor...............8W-30-10, 16
Data Link Connector...................8W-30-11, 17
Daytime Running Lamps (DRL) Module.......8W-30-11, 17
Engine Coolant Temperature Sensor..........8W-30-9, 18
Fuel Pump Relay........................8W-30-20
Fuel Tank Level Unit......................8W-30-21
Fuse 1 (PDC)........................8W-30-6, 14
Fuse 4 (PDC)........................8W-30-6, 14
Fuse 5 (Fuse Block).................8W-30-6, 14, 20
Heated Oxygen Sensor..................8W-30-7, 15
Idle Air Control Motor..................8W-30-12, 18
Ignition Switch.....................8W-30-6, 14, 20
Ignition Coil........................8W-30-12, 18
Injectors (4.0L).........................8W-30-13
Injectors (2.5L)..........................8W-30-8
Instrument Cluster....................8W-30-11, 17
Intake Air Temperature Sensor.............8W-30-9, 18
MAP Sensor.........................8W-30-9, 18
Power Steering Pressure Switch..............8W-30-12
Powertrain Control Module.............8W-30-6 thru 21
Throttle Position Sensor.................8W-30-9, 18
Vehicle Speed Sensor..................8W-30-11, 17
J8W-30 FUEL/IGNITIONÐYJ VEHICLES 8W - 30 - 5

REAR LIGHTING
TAIL LAMPS AND LICENSE PLATE LAMPS
Circuit A6 in the Power Distribution Center (PDC)
connects to a bus bar in the fuse block. The fuse
block bus bar powers circuit F33. Circuit F33 con-
nects to the headlamp switch. Fuse 3 in the PDC
protects circuit A3. Fuse 8 in the fuse block protects
circuit F33.
The headlamp switch has three positions: ON,
PARK (parking lamps) and OFF, plus a dimmer
switch. When the headlamp switch is in the PARK or
ON position, the switch connects circuit F33 to cir-
cuit L7. From the headlamp switch, circuit L7
branches to power the front parking lamps and rear
tail and license plate lamps. The lamps are case
grounded.
HELPFUL INFORMATION
²If the vehicle is equipped with factory installed fog
lamps, circuit L7 splices to feed the park lamp relay.
²Jumper harnesses connect the tail, stop, turn sig-
nal lamp to the body harness.
²Check fuse 3 in the PDC.
²Check fuse 8 in the fuse block.
²Circuit L7 also feeds the radio, if equipped.
STOP LAMPS AND CHMSL LAMPS
Circuit A6 from fuse 3 in the Power Distribution
Center (PDC) supplies voltage to the fuse block bus
bar. The bus bar powers circuit F32 through fuse 3 in
the fuse block. Circuit F32 connects to the stop lamp
switch.
When the operator depresses the brake pedal, the
stop lamp switch closes, and connects circuit F32 to
circuit L50. Circuit L50 connects to the CHMSL
lamps and turn signal/hazard flasher. Circuit Z1 pro-
vides ground for the CHMSL lamps. The turn signal/
hazard flasher supplies current to the L62 and L63
circuits. Circuit L62 powers the right stop lamp. Cir-
cuit L63 powers the left stop lamp. The stop lamps
are case grounded.
HELPFUL INFORMATION
²Circuits L50 and Z1 pass through contacts in the
rear door before reaching the CHMSL lamps.
²Check fuse 3 in the PDC.²Check fuse 3 in the fuse block.
²Check for continuity across the stop lamp switch
when it is closed.
²If the vehicle is equipped with anti-lock brakes,
circuit L50 connects to the ABS module.
BACK-UP LAMPS
In the START or RUN position, the ignition switch
connects circuit A1 from fuse 4 in the Power Distri-
bution Center (PDC) to circuit A21. Circuit A21 feeds
a bus bar in the fuse block that powers circuit G5
through fuse 9.
Circuit G5 splices to supply power to the back-up
lamp switch. On automatic transmission vehicles, the
back-up lamp switch is part of an assembly that in-
cludes the PARK/NEUTRAL position switch.
When the operator puts the transmission in Re-
verse, the back-up lamp switch connects circuit G5 to
circuit L1. Circuit L1 feeds the case grounded
back-up lamps.
HELPFUL INFORMATION
²Check fuse 4 in the PDC.
²Check fuse 9 in the fuse block.
²Check for continuity across the back-up lamp
switch when it is closed.
DIAGRAM INDEX
Component Page
ABS Control Module......................8W-51-3
Back-Up Lamps..........................8W-51-4
Back-Up Lamp Switch.....................8W-51-2
Center High Mounted Stop Lamps (CHMSL).......8W-51-3
Fuse 3 (Fuse Block).......................8W-51-2
Fuse 3 (PDC)...........................8W-51-2
Fuse 4 (PDC)...........................8W-51-2
Fuse 9 (Fuse Block).......................8W-51-2
Fuse 8 (Fuse Block).......................8W-51-2
Headlamp Switch.........................8W-51-2
Ignition Switch..........................8W-51-2
Powertrain Control Module..................8W-51-3
Stop Lamp Switch........................8W-51-3
Tail, Stop, and Turn Signal Lamps.............8W-51-4
J8W-51 REAR LIGHTINGÐYJ VEHICLES 8W - 51 - 1