1994 TOYOTA CAMRY engine

tires check oil battery location coolant reservoir washer fluid air bleeding

Page 185 of 307

TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual 185
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 18 OF THE WIPER AND WASHER SW, TERMINAL 2 OF
THE WASHER MOTOR AND TERMINAL 4 OF THE WIPER MOTOR THROUGH THE WIPER FUSE.
1. LOW SPEED P

185
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 18 OF THE WIPER AND WASHER SW, TERMINAL 2 OF
THE WASHER MOTOR AND TERMINAL 4 OF THE WIPER MOTOR THROUGH THE WIPER FUSE.
1. LOW SPEED POSITION
WITH WIPER SW TURNED TO LOW POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT LOW SPEED.
2. HIGH SPEED POSITION
WITH WIPER SW TURNED TO HIGH POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 13 " TERMINAL 2 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT HIGH SPEED.
3. INT POSITION
WITH WIPER SW TURNED TO INT POSITION, THE RELAY OPERATES AND THE CURRENT WHICH IS CONNECTED BY RELAY
FUNCTION FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND. THIS FLOW OF CURRENT
OPERATES THE INTERMITTENT CIRCUIT AND THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE WIPER FUNCTIONS.
THE INTERMITTENT OPERATION IS CONTROLLED BY A CONDENSER'S CHARGED AND DISCHARGED FUNCTION INSTALLED IN
RELAY AND THE INTERMITTENT TIME IS CONTROLLED BY A TIME CONTROL SW TO CHANGE THE CHARGING TIME OF THE
CONDENSER.
4. WASHER CONTINUOUS OPERATION
WITH WASHER SW TURNED TO ON, THE CURRENT FLOWS FROM TERMINAL 2 OF THE WASHER MOTOR " TERMINAL 1 "
TERMINAL 8 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND AND CAUSES TO THE WASHER MOTOR TO RUN AND
WINDOW WASHER TO JET. THIS CAUSES THE CURRENT TO FLOW TO WASHER CONTINUOUS OPERATION CIRCUIT IN TERMINAL 18
OF THE WIPER AND WASHER SW " TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE
WIPER FUNCTION.
C13 FRONT WIPER AND WASHER SW (W/ WIPER RELAY) [COMB. SW]
16±GROUND : ALWAYS CONTINUITY
18±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT LOW OR MIST POSITION
APPROX. 12 VOLTS 2 TO 12 SECONDS INTERMITTENTLY WITH WIPER SW AT INT POSITION
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON UNLESS WIPER MOTOR AT STOP POSITION
13±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT HIGH POSITION
F 9 FRONT WIPER MOTOR
5±6 : CLOSED UNLESS WIPER MOTOR AT STOP POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1332F 928 (1MZ±FE), 30 (5S±FE)W 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IR144ENGINE ROOM MAIN WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA38 (1MZ±FE)FRONT RIGHT FENDEREA40 (5S±FE)FRONT RIGHT FENDER
IE42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E138 (1MZ±FE)ENGINE ROOM MAIN WIREI 544COWL WIREE 140 (5S±FE)ENGINE ROOM MAIN WIRE
SYSTEM OUTLINE
SERVICE HINTS