
How to Use this Manual 
These  symbols are on some of your 
controls:  These  symbols 
are used  on  warning 
and  indicator  lights:  Here 
are  some  other  symbols you 
may  see: 
Windshield  Wipers 
Engine  Coolant 
Temperature  Fuse 
w Windshield 
Washer 
Battery  Charging 
System  Tailgate  Window 
Windshield  Defroster  Lighter 
Fuel 
Rear  Window  Defogger  Horn 
Speaker 
Engine 
Oil Pressure 
Rear  Window  Wiper 
Brake 
Hood  Release 
Rear  Window 
WiperlWasher  Anti-Lock  Brakes 
Ventilating  Fan 
Power  Window 
10 
ProCarManuals.com 

Engine  Coolant  Heater (Engine 
Block Heater) 
(OPTION) 
In  very  cold  weather, 0°F (-18°C) or 
colder,  the engine  coolant  heater  can 
help. 
You’ll get  easier  starting  and 
better  fuel economy during  engine 
warm-up.  Usually, the coolant  heater 
should  be plugged  in a minimum  of four 
hours  prior to starting  your vehicle. 
To use  the  coolant  heater: 
1. Turn off the engine. 
2. Open  the  hood and  unwrap  the 
3. Plug it  into  a normal, grounded 110- 
electrical  cord. 
volt  outlet. 
NOTICE: 
After  you’ve  used the coolant 
heater,  be sure  to store  the  cord as 
it  was  before  to keep  it away  from 
moving  engine  parts. If you  don’t,  it 
could  be  damaged.  How  long 
should you keep  the coolant 
warmer  plugged  in? The answer 
depends  on  the  weather,  the kind  of oil 
you  have,  and some  other things. 
Instead  of trying  to list  everything  here, 
we  ask  that  you contact  an  Oldsmobile 
dealer 
in the  area  where you’ll be 
parking  your  vehicle.  The dealer  can 
give  you  the best  advice  for  that 
particular  area. I 
ProCarManuals.com 

U 
E/M sw&h (ELECTRONIC  CLUSTER) 
To change your electronic display from 
English  to metric  units,  or  from metric 
co English, press  this switch  down.  The 
gages  affected  are: 
Speedometer 
Odometer 
Trip Odometer 
Oil Pressure 
Engine  Coolant  Temperature 
mn-irrnrIII 
The  tachometer  displays the engine 
speed  in revolutions per  minute  (rpm) 
. 
NOTICE: 
Do not  operate  the  engine with the 
tachometer  in  the  red area,  or 
engine 
damage may occur. 
4"' UNLEADED FUEL ONLY c 
he/ Gage (STANDARD CLUSTER) 
Your  fuel  gage  tells you about  how 
much  fuel  you  have left, when  the 
ignition  is on.  When  the indicator  nears 
E (Empty), you will  have  a little  fuel left 
but  should  get more  soon. 
Here  are four things  that some owners 
ask  about.  None of these  show a 
problem with your  fuel  gage: 
At the  service  station,  the  gas pump 
shuts  off before  the gage  reads 
F (Full) . 
83 
ProCarManuals.com 

VOLTS 
Voltmeter (STANDARD CLUSTER) 
Your charging  system  gage  will  show 
the  rate  of charge  when the engine  is 
running.  When the engine  is not 
running  but  the ignition  is on  (in  the 
Run position),  the display  measures  thc 
voltage  output of your  battery. 
The  reading  will change  as  the  rate 
of 
charge changes (with engine speed, 
etc.),  but  readings between  the warning 
zones  indicate  the normal operating 
range.  Readings  in either warning zone 
indicate a  possible problem with your 
charging  system.  Have your  Oldsmobilc 
serviced  immediately. 
-100 
Engine  Coolant  Temperature 
Gage 
(STANDARD  CLUSTER) 
This gage  shows  the engine coolant 
temperature.  If the  gage  pointer  moves 
into  the  red area,  your engine is  too 
hot! 
It means  that your  engine coolant 
has  overheated. 
If  you  have  been operating  your  vehicle 
under normal  driving conditions,  you 
should  pull 
off the  road,  stop  your 
vehicle  and turn  off the  engine  as soon 
as  possible. 
HOT  COOLANT  CAN  BURN 
YOU 
BADLY! 
In 
Problems on the  Road, this manual 
shows what  to do.  See  the 
Index under 
Engine  Overheating. 
0 
0 
0 
Fuel  Gage (ELECTRONIC  CLUSTER) 
Your  fuel  gage bars light  up  when  the 
ignition is on 
to show  you about  how 
much  fuel  you  have  left. 
When  the gage  first indicates empty, 
you  still  have 
a little  fuel left,  but you 
should  get more  soon. 
A  box  around  the  gas pump  symbol  wil: 
flash  when  your tank is 
1/8 full or less. 
Here  are  five things  that some owners 
ask  about.  None  of these show 
a 
problem  with your  fuel  gage: 
At the  service  station,  the  gas pump 
shuts 
off before  the gage  reads full. 
The top bar does  not go out  until  you 
have  driven  a long  distance-about 
3r 
miles (48 kilometers). 
51 
85 
ProCarManuals.com 

Features & Controk 
88 
Engine  Coolant  Temperature Gage 
pcmoNIc CLUSTER) 
This  gage  has bars  that show  the engine 
coolant temperature. 
A box  around  the  temperature  symbol 
will  flash  when your engine 
is too hot. 
It means  that your  engine  coolant has 
overheated.  If you  have  been  operating 
your  vehicle  under normal  driving 
conditions,  you should  pull 
off the road, 
stop  your  vehicle  and turn 
off the 
engine  as soon as  possible. 
HOT  COOLANT 
CAN BURN YOU 
BADLY! 
In ProbZems on the Road, this manual 
shows what  to do.  See  the 
Index under 
Engine  Overheating. 
~ 
Brake  System  Warning  Light 
Your  Oldsmobile’s  hydraulic  brake 
system  is  divided  into two parts. 
If one 
part isn’t  working, the other part can 
still  work and stop  you.  For  good 
braking, though,  you  need both parts 
working  well. 
If  the  warning  light  comes  on, there 
could  be  a brake problem.  Have  your 
brake  system  inspected  right  away. 
This  light  should  come  on as you  start 
the  vehicle.  If it doesn’t come on  then, 
have  it fixed 
so it  will  be  ready  to warn 
you 
if there’s a  problem. 
If  the  light  comes  on while  you  are 
driving,  pull  off the  road  and stop 
carefully. 
You may  notice  that  the  pedal 
is  harder to push.  Or,  the pedal  may  go  closer 
to  the floor.  It  may  take longer  to 
stop. 
If the  light  is still on, have  the 
vehicle  towed for  service. (See 
Towing 
Your Truck in the Index.) 
The  brake  system  warning  light  will  also 
come  on  when  you  set  your  parking 
brake, and it  will  stay  on 
if your  parking 
brake doesn’t  release  fully. If it  stays 
on 
after  your  parking  brake  is  fully  released, 
it means  you  have  a brake  problem. 
ProCarManuals.com 

ducts at your  feet. At times  this 
temperature  difference  may  be  more 
apparent  than  others. 
VENT: The vent setting brings in 
outside air through  the instrument 
panel  outlets and  at your  front  side 
windows. 
HTR The heater  setting  brings  in most 
heated air through  the heater ducts,  and 
some through  the defroster  vents. 
If  you  have  the optional engine coolant 
heater and use it during  cold weather, 
20°F (-8°C) or lower,  your heating 
system  will  more quickly  provide  heat 
because  the engine coolant is  already 
warmed.  See the 
Index under Engine 
Coolant  Heater. 
most of the  warmed air  to  the 
windshield  and side windows. Some 
will  also 
go to  the  floor vents. 
The air conditioner  will also  run in this 
setting  to remove moisture from  the air 
when  the  temperature  is  above 
40°F 
(4°C). Adjust the temperature  control 
as  desired. 
(Defrost): This setting directs 
Defogging  and  Defrosting 
To rapidly  defrost the windshield,  slide 
the  temperature  control  lever  all the 
way  up  and  select the 
(j@ setting. 
Adjust  the fan to  the  highest  speed. 
To rapidly  defog  the side windows, 
select  the 
BI-LEV AfC setting and 
adjust  the fan to  the  highest  speed.  Aim 
the  side  vents toward  the side  windows. 
For  increased air  flow to  the  side vents, 
close  the center vents. 
r 
93 
ProCarManuals.com 

Your Driving and the Road 
130 
Winter Driving 
Here are some  tips for winter  driving: 
Have  your  Oldsmobile  in good  shape 
for  winter.  Be sure  your  engine 
coolant  mix  is  correct. 
You  may  want to put winter 
emergency  supplies  in your  vehicle. 
Include  an ice  scraper, 
a small  brush or 
broom, 
a supply  of windshield  washer 
fluid, 
a rag,  some  winter outer clothing, 
a  small  shovel,  a  flashlight,  a  red  cloth, 
and  a  couple  of reflective  warning 
triangles.  And, if you  will  be driving 
under  severe  conditions,  include  a  small 
bag  of sand,  a  piece  of old  carpet or  a 
couple 
of burlap  bags to help  provide 
traction.  Be sure  you  properly  secure 
these  items  in your  vehicle. 
Driving  on Snow  or Ice 
Most  of the  time,  those  places  where 
your  tires  meet  the road  probably  have 
good  traction. 
However, 
if there  is  snow  or ice 
between  your  tires  and the road,  you 
can  have  a  very  slippery  situation. 
You’ll  have  a  lot less  traction or “grip” 
and  will  need  to be  very  careful. 
What’s  the worst  time  for  this? “Wet 
ice.”  Very  cold  snow  or ice  can be  slick 
and hard  to drive  on. But  wet  ice can  be 
even  more  trouble because  it may  offer 
the  least  traction  of all.  You  can get 
“wet  ice” when  it’s about  freezing 
(32°F; 0.C) and freezing  rain begins  to 
fall.  Try  to avoid  driving  on wet  ice  until 
salt  and  sand  crews  can get there.  Whatever 
the condition 
- smooth  ice, 
packed,  blowing  or loose  snow 
- drive 
with  caution. 
Accelerate  gently.  Try  not to break  the 
fragile  traction.  If you  accelerate  too fast, 
the  drive  wheels  will  spin  and  polish  the 
surface  under  the tires  even  more. 
Your  anti-lock  brakes  improve  your  ability  to make  a  hard  stop on 
a slippery 
road.  Even though  you have  an anti-lock 
braking  system,  you’ll  want to begin 
stopping  sooner  than you  would  on dry 
pavement.  See 
Anti-Lock in the Index. 
Allow  greater  following  distance on 
any  slippery  road. 
Watch for  slippery  spots. The road 
might  be fine  until  you  hit a spot 
that’s  covered  with ice. On  an 
otherwise  clear  road, ice  patches  may 
appear in shaded areas where  the  sun 
can’t  reach:  around clumps  of trees, 
behind  buildings,  or  under bridges. 
Sometimes  the surface  of a  curve  or 
an  overpass  may remain  icy when  the 
surrounding  roads are clear. 
If you  see 
a patch  of ice  ahead  of you,  brake 
before  you are on it. Try  not to brake 
while  you’re  actually  on  the ice, and 
avoid  sudden  steering  maneuvers. 
ProCarManuals.com 

When  your  vehicle  is  being towed, have 
the  ignition  key  off. The steering  wheel 
should  be clamped in a straight-ahead 
position, with a  clamping  device 
designed  for towing  service. 
Do not  use 
the  vehicle’s  steering column  lock for 
this. The transmission  should  be in 
P (Park)  and the parking brake 
released. 
Don’t  have  your  Bravada towed with 
the  wheels  in  contact with  the ground. 
If your  vehicle  is  being  towed with 
sling-type  or  wheel-lift  equipment, 
either  the front  or rear  wheels  must be 
supported on a  dolly. 
If  towing  your  Bravada with a  car 
carrier,  block supports  may  be required 
to  prevent  damage  to  the vehicle. 
Engine Overheating 
You will  find  a coolant temperature 
;age  and the warning  light about 
a hot 
mgine  on your  Oldsmobile’s  instrument 
)anel. 
If Steam Is Coming  From  Your 
Engine 
!45 
ProCarManuals.com