1994 MAZDA MX-5 clutch

TRANSMISSION J Mainshaft Parts Assemble in the order shown in the figure, referring to Assembly Note. WPPLY SPEwim OIL To IwiviDwL PmTs 45UOJX-034 Clutch hub Synchronizer key Clutch hub sleeve Synchronizer key springs Mainshaft 2nd gear Assembly Note .............. page J-32 2nd synchronizer ring Double cone Inner cone Synchronizer assembly (2nd) Clutch hub assembly (Istf2nd) Assembly Note .............. page J-32 3rd gear Assembly Note .............. page J-32 3rd synchronizer ring Clutch hub assembly (3rdl4th) Assembly Note .............. page J-32 Snap ring Assembly Note .............. page J-32 1 st synchronizer ring Bearing race Assembly Note .............. page J-32 Bearing Assembly Note .............. page J-32 1 st gear Assembly Note .............. page J-32 5-31 Gartner Banana

J TRANSMISSION Assembly note Clutch hub assembly 1. Set the 2nd gear, 2nd synchronizer ring, and 1stl2nd clutch hub assembly on the mainshaft, then press in the mainshaft. 2. Set the 3rd gear, 3rd synchronizer ring, and 3rdl4th clutch hub assembly on the mainshaft, then press them onto the mainshaft by using the SST. 3. Install a new snap ring on the front of the mainshaft. 4. Install the bearing race, bearing, and 1 st gear. Gartner Banana

TRANSMISSION 1. Clutch hub 2. Synchronizer key 3. Clutch hub sleeve b 4. Synchronizer key springs 5. 4th synchronizer ring 6. Bearing 7. Main drive gear 8. Bearing housing assembly 9. Washer 10. Mainshaft gear assembly Assembly Note .................. below 1 1 . Spacer 12. Countershaft .................. Assembly Note below 13. Counter reverse gear 14. Washer 15. Bearing race 16. Bearing 17. Reverse gear 18. Reverse synchronizer ring 19. Clutch hub assembly (5thlReverse) 20. Locknut (Mainshaft) .................. Assembly Note below 21. 5th synchro-niter ring 22. 5th gear 23. Steel ball 24. Thrust lock washer .............. Assembly Note page J-36 25. C-washer .............. Assembly Note page J-36 26. Retaining ring .............. Assembly Note page J-36 27. Spacer 28. Counter 5th gear 29. Mainshaft rear bearing .............. Assembly Note page J-36 30. C-washer .............. Assembly Note page J-36 31. Retaining ring .............. Assembly Note page J-36 32. Washer .............. Assembly Note page J-36 33. Snap ring 34. Countershaft rear bearing .............. Assembly Note page J-36 35. Locknut (Countershaft) .............. Assembly Note page J-37 45UOJX437 Assembly note Mainshaft and countershaft 1. Place the mainshaft gear assembly and the countershaft on the bearing housing. 2. Use a suitable bar to press in the countershaft. Locknut (Mainshaft) 1. Secure the bearing housing assembly in a vise. 2. Shift the clutch hub sleeves into 1 st and Reverse gears to lock the rotation of the mainshaft. 3. Install a new locknut and tighten it by using the SST. Tightening torque: 128-235 N.m (13-24 kgf.m, 95-173 ftdbf) 4. Use a chisel to stake the locknut. Gartner Banana

TRANSMISSION J & BEARING HOUSING Locknut (Countershaft) 1. Shift the clutch hub sleeves into 1 st and Reverse gears to lock the rotation of the mainshaft. 2. Connect the SST to the mainshaft and secure it in a vise. 3. Install a new locknut and tighten it. Tightening torque: 128-1 96 N.m (13-20 kgf-m, 95--144 ft-lbf) 4. Use a chisel to stake the locknut. Gartner Banana

J TRANSMISSION CLUTCH SLEEVE SYNCHRONIZER KEY Shift fork and rod, interlock pin 1. Set the 1 stf2nd shift fork onto the 1 sV2nd clutch hub assembly. 2. Install the 3rdI4th shift fork and 3rdl4th shift rod, and ii install the interlock pin into the bearing housing as shown in the interlock pin assembly note. (Refer to page J-39.) Roll pin Install a new roll pin into each shift fork. The roll pin must be installed with the split facing as shown. Spring, spacer, clip 1. Slide the spring and spacer onto the 5thlReverse shift rod. While pressing the spacer, install a new clip. 2. Install new clips to the 3rdl4th shift rod and 1 sV2nd shift rod. 3. Verify that the centers of the shift fork and clutch hub sleeve are aligned properly< If they are not, select the proper washer to install between 1st gear and the mainshaft front bearing, and between reverse gear and the mainshaft front bearing. Gartner Banana

TRANSMISSION J 1. Oil seal Assembly Note .................. below 2. Snap ring u 3. Steel ball 4. Speedometer drive gear 5. Snap ring 6. Transmission case 7. Extension housing Assembly Note .................. below 8. Main drive gear bearing Assembly Note .................. below 9. Snap ring 10. Countershaft front bearing Assembly Note .............. page J-44 11. Snap ring 12. Adjustment shim Assembly Note .............. page J-44 13. Gasket 14. Front cover 15. Speedometer driven gear 16. Neutral switch 17. Back-up light switch 18. Boot 19. Clutch release fork Assembly Note .............. page J-44 20. Clutch release collar Assembly Note .............. page J-44 35UOJX-020 Assembly note Oil seal 1. Apply transmission oil to the outer periphery. 2. lnstall a new oil seal with the SST. Extension housing 1. Apply sealant to the contact surfaces of the bearing housing and transmission case. 2. Align the inner shift lever and shift rod end groove, and install the extension housing. 3. Apply sealant to the bolt threads, and install the bolts. Tightening torque: 18-26 N.m (1.8-2.7 kgf.m, l4--19 ft4bf) Main drive gear bearing Install the main drive gear bearing by using the SST, and secure it with a new snap ring. Gartner Banana

J TRANSMISSION TRANSMISSION CASE SNAP RING Countershaft front bearing Install the countershaft front bearing by using the SST, and secure it with a new snap ring. d Adjustment shim After measuring dimensions (A) and (B) shown in the fig- ure, use an adjustment shim(s), as specified below, of the thickness corresponding to the value of (A) minus (B), so that bearing end play will be within specification. Bearing end play: 04.lmm (0-0.004 in) Adjustment shim thickness: 0.lOmm (0.004 in), 0.15mm (0.006 in), 0.30mm (0.012 in) Clutch release fork 1. Apply Mori White TA No.2 or equivalent organic rnolyb- denum grease to the shaded areas of the clutch release collar and release fork. 2. Install the clutch release collar and clutch release fork. Gartner Banana

TRANSMISSION J INSTALLATION 1. On level ground, jack up the vehicle and support it evenly on safety stands. 2. Install in the order shown in the figure, referring to lnstallation Note. L 3. Add the specified amount of the specified transmission oil. (Refer to page J-8.) 4. Warm up the engine and transmission, and inspect for oil leakage and transmission problems. 1. Transmission 7. Exhaust pipe Installation Note ............. page J-46 8. Performance rod 2. Power plant frame (PPF) 9. Differential mounting pipe Installation Note ............. page J-46 10. Undercover 3. S~eedometer cable 11. Shift lever w 4. ~iarter Installation Note ............. page J-47 5. Clutch release cylinder 12. Rear console 6. Propeller shaft 13. Shift lever knob Service ...................... section L Gartner Banana