1994 MAZDA MX-5 wheel bolts

FRONT SUSPENSION (DOUBLE-WISHBONE) LOWER ARM Removal / lnspection I Installation 1. Jack up the front of the vehicle and support it with safety stands. 2. Remove the undercover. 3. Remove in the order shown in the figure, referring to Removal Note. 4. lnspect all parts and repair or replace as necessary. 5. Install in the reverse order of removal, referring to lnstallation Note. 6. Loosely tighten the lower arm, shock absorber, and stabilizer control link bolts. Tighten all other nuts and bolts to the specified torque with the vehicle unladen. 7. Lower the vehicle. 8. With the vehicle unloaded, tighten the lower arm, shock absorber, and stabilizer control link bolts to the - specified torques. 9. Adjust the front wheel alignment. (Refer to page R-6.) 1. Wheel and tire 15UORX-012 5. Ball joint dust boot 2. Stabilizer control link bolt emo oval ~ote ............. page R-16 3. Shock absorber bolt Installation Note ........... page R-16 u 4. Lower arm ball joint 6. Lower arm Removal Note ............. page R-16 Inspect for damage and cracks Inspection ................. page R-16 7. Lower arm bushing (front and rear) lnspect for deterioration and wear Gartner Banana

FRONT SUSPENSION (DOUBLE-WISHBONE) R UPPER ARM Removal I Inspection I Installation 1. Jack up the front of the vehicle and support it with safety stands. L/ 2. Remove the undercover. 3. Remove the band for the wheel speed sensor harness. 4. Remove in the order shown in the figure, referring to Removal Note. 5. lnspect all parts and repair or replace as necessary. 6. Install in the reverse order of removal, referring to Installation Note. 7. Loosely tighten the upper arm and shock absorber bolts. Tighten all other nuts and bolts to the specified torques. 8. Install the band for the wheel speed sensor harnes. 9. Lower the vehicle. 10. With the vehicle unloaded, tighten the upper arm and shock absorber bolts to the specified torques. 11. Adjust the front wheel alignment. (Refer to page R-6.) 25UORX-01 1. Wheel and tire 5, Ball ioint dust boot Upper arm ball joint demoval ~ote ............. page R-18 Removal Note ............. page R-18 Installation Note ........... page R-18 Shock absorber bolt 6. Upper arm bushing (front and rear) 4. Upper arm Inspect for deterioration and damage Inspect for damage and cracks Gartner Banana

FRONT SUSPENSION (DOUBLE-WISHBONE) CROSSMEMBER Removal I Inspection 1 lnstallation Note 4 Use a container or rags to collect the power steering fluid when disconnecting the power steering pipes. 1. Jack up the vehicle. 2. Remove the wheels and the undercover. 3. Support the engine with a hoist. 4. Lower the crossmember and other suspension parts as an assembly, and then separate the parts. 5. Remove in the order shown in the figure. 6. lnspect all parts and repair or replace as necessary. 7. Loosely tighten the stabilizer bracket, upper arm, and lower arm bolts. Tighten all other nuts and bolts to the specified torques. 8. Lower the vehicle. 9. With the vehicle unloaded, tighten the stabilizer bracket, upper arm, and lower arm bolts to the specified torques. 10. Adjust the front wheel alignment. (Refer to page R-6.) 11. Bleed the air from the brake system. (Refer to section P.) 12. Bleed the air from the Power Steering System. (Refer to section N.) Q - re-no ~L1.3--11.W, Okl-m} 94-1;2 (9.Cll.5,69--83) 1 &26 {1.&2.7,14--19) 1 S21 (1 3-- 1. Brake pipe Removal / lnstallation . . . . . . . . . Section P 2. Pinion shaft bolt Removal / lnstallation . . . . . . . . Section N 3. Power steering pipe Removal 1 lnstallation . . . . . . . . Section N 4. Shock absorber bolt 5. Stabilizer bracket bolt 6. Upper arm bolt 7. Performance rod 8. Adjusting cam bolt 9. Steering gear bracket bolt 10. Front crossmember assembly lnspect for damage Gartner Banana

R REAR SUSPENSION (DOUBLE-WISHBONE) SHOCK ABSORBER AND SPRING Removal / Installation 1. Jack up the front of the vehicle and support it with safety stands. 2. Remove in the order shown in the figure, referring to Removal Note. 3. Inspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Loosely tighten the stabilizer control link bolt. Tighten all other nuts and bolts to the specified torques. 6. Lower the vehicle. 7. With the vehicle unloaded, tighten the stabilizer control link bolt to the specified torques. 8. Adjust the rear wheel alignment. (Refer to page R-9.) Nm (kgfm, ft4bf) 1. Wheel and tire 2. Filler pipe protector (left side) 3. Stabilizer control link bolt 4. Shock absorber and spring Removal Note . . . . . . . . . . . . . page R-22 Disassembly l Inspection / Assembly . . . . . . . . . . . . . . . . page R-13 Removal note Shock absorber and spring Caution Do not lower the arms excessively, which may damage the brake hose. 1. Loosen the upper arm and Adjusting cam nuts. 2. Lower the upper and lower arms to remove the shock absorber and spring. Gartner Banana

REAR SUSPENSION (DOUBLE-WISHBONE) LOWER ARM Removal / Inspection / Installation 1. Jack up the rear of the vehicle and support it with safety stands. 2. Remove in the order shown in the figure. 3. lnspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Loosely tighten the lower arm, shock absorber, and stabilizer control link bolts. Tighten all other nuts and bolts to the specified torques. 6. Lower the vehicle. 7. With the vehicle unloaded, tighten the lower arm, shock absorber, and stabilizer control link bolts to the - specified torques. 8. Adiust the rear wheel alignment. (Refer to page R-9.) 1. Wheel and tire 2. Stabilizer control link bolt 3. Shock absorber bolt 4. Lower arm lnspect for damage and cracks 5. Lower arm bushing (crossmember side and knuckle side) lnspect for deterioration and wear Gartner Banana

REAR SUSPENSION (DOUBLE-WISHBONE) UPPER ARM Removal I Inspection I Installation 1. Jack up the rear of the vehicle and support it with safety stands. 2. Remove in the order shown in the figure. 3. lnspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Loosely tighten the upper arm bolts. Tighten all other nuts and bolts to the specified torques. 6. Lower the vehicle. 7. With the vehicle unloaded, tighten the upper arm bolts to the specified torques. 8. Adjust the rear wheel alignment. (Refer to page R-9.) REPLACE 1. Wheel and tire 2. Upper arm lnspect for damage and cracks 3. Upper arm bushing lnspect for deterioration and wear Gartner Banana

R REAR SUSPENSION (DOUBLE-WISHBONE) CROSSMEMBER Removal I Inspection I Installation 1. Jack up the vehicle and support it with safety stands. 2. Remove the wheels and tires. d 3. Remove the differential and the power plant frame. (Refer to section M.) 4. Lower the crossmember and other suspension parts as an assembly, and then separate the parts. 5. Remove in the order shown in the figure. 6. lnspect parts and repair or replace as necessary. 7. Install in the reverse order of removal. 8. Loosely tighten the stabilizer bracket, upper arm, and lower arm bolts. Tighten all other nuts and bolts to the specified torques. 9. Lower the vehicle. 10. With the vehicle unloaded, tighten the stabilizer bracket, upper arm, and lower arm bolts to the specified torques. 11. Adjust the rear wheel alignment. (Refer to page R-9.) 12. Bleed the air from the brake system. (Refer to section P.) 13. Adjust the parking brake lever stroke. (Refer to section P.) 1. Differential mounting pipe 6. Shock absorber bolt 2. Parking brake cable 7. Stabilizer bracket Removal / Installation . . . . . . . . . Section P 8. Upper arm bolt 3. Brake pipe 9. Adjusting cam bolt Removal / Installation . . . . . . . . . Section P 10. Rear crossmember assembly 4. Brake pipe joint Inspect for damage 5. Battery cable bracket Gartner Banana