1994 MAZDA MX-5 wheel bolts

MANUAL STEERING , N Removal / Installation 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure, referring to Removal Note. ,, 3. Inspect all parts and repair or replace as necessary. 4. Install in the reverse order of removal. 5. Tighten all necessary nuts and bolts to the specified torque. 6. After installation, check if the horn sounds. If the horn does not sound, remove the air bag module and connect the module connectors. (Refer to section T.) 1. Air bag module 6. Lower panel Removal 1 Installation .......... section T 7. Key interlock cable (Automatic transmission) 2. Locknut 8. Intermediate shaft bolt 3. Steering wheel 9. Steering shaft w ............... Removal Note page N-10 Disassembly 1 Inspection / 4. Column cover Assembly .................. page N-10 5. Combination switch Removal / Installation .......... section T Gartner Banana

N MANUAL STEERING Removal Note Steering wheel Caution '. Do not try to remove the steering wheel by hitting the shaft with a hammer. The column will col- lapse. Remove the steering wheel with a suitable puller. Disassembly 1 Inspection 1 Assembly 1. Disassemble in the order shown in the figure, referring to Disassembly Note. 2. Assemble in the reverse order of disassembly, referring to Assembly Note. L 1. Steering lock mounting bolts and bracket 3. Steering shaft ................... Disassembly Note ............ page N-1 1 Inspection page N-1 1 Assembly Note .............. page N-11 4. Intermediate shaft J 2. Steering lock assembly Inspect universal joint for looseness, abnormal noise, and sticking Gartner Banana

N ENGINE SPEED SENSING POWER STEERING TROUBLESHOOTING GUIDE Steering feels heavy - - Poor lubrication, foreign material, or abnormal wear of steering ball joint Stuck or damaged lower arm ball joints lmproper steering pinion preload Damaged steering gear Malfunctioning steering shaft joint Problem I lmproperly adjusted wheel alignment Possible Cause 1 Malfunctioning steering gear lncorrect tire pressure Loose or damaged oil pump drive belt Low fluid level or air in fluid I Leakage of fluid I Insufficient oil pump pressure Steering wheel pulls lncorrect tire pressure to one side Unevenly worn tires ( Weak front spring General instability while driving Worn or damaged stabilizer and/or upper or lower arm bushing Dragging brake Loose lower arm lmproperly adjusted wheel alignment lncorrect tire pressure Damaged or unbalanced wheel Worn or damaged steering joint(s) lmproper steering pinion preload Weak front coil spring Worn or damaged stabilizer and/or upper or lower arm bushing Malfunctioning shock absorber Cracked or worn engine mount Cracked or worn transmission mount Shake (Steering wheel vibrates up/ down) Shimmy (Steering wheel vibrates left1 right) lmproperly adjusted wheel alignment Excessive tire and/or wheel runout Loose lug nuts Unbalanced wheel(s) Excessive steering wheel play Poor steering wheel return Cracked or worn steering gear mount Loose steering gear mounting bolts Stuck or damaged steering ball joint Excessive tire and/or wheel runout Loose lug nuts Unbalanced wheel@) lncorrect tire pressure Unevenly worn tires Malfunctioning shock absorber Loose shock absorber mounting bolts Stuck or damaged lower arm ball joint Cracked or worn suspension bushings Damaged or worn front wheel bearing lmproperly adjusted front wheel alignment Worn steering gear Worn or damaged steering joints Worn or damaged lower arm bushing Loose steering gear mounting bolts Worn linkage or tie-rod ball joint lncorrect tire pressure Stuck or damaged steering joints lmproperly adjusted front wheel alignment lmproper steering pinion preload Ball joint not operating smoothly Steering shaft contacting something Action Lubricate or replace Replace Adjust Replace Replace Adjust Replace Adjust Adjust or replace Add fluid or bleed air Repair or replace Replace Adjust Replace Replace Replace Repair Tighten or replace Adjust Adjust Adjust or replace Replace Adjust Replace Replace Replace Adjust Replace Tighten Adjust or replace Replace Replace Replace Tighten Replace Replace Tighten Adjust or replace Adjust Replace Replace Tighten Replace Replace Replace Adjust Replace Replace Replace Tighten Replace Adjust Replace Adjust Adjust Replace Repair Pagelsection N-25 section R N-32 N-25 N- 9 section R N-25 section Q N-37 N-21,22 - N-34 section Q section Q section R section R section P section R section R section Q section Q N- 9 N-32 section R section R section R section R section Q section Q section Q section B section J N-26 N-25 N-25 section Q section Q section Q section Q section Q section R section R section R section R section M section R N-25 N- 9 section R N-25 N-25 section Q N- 9 section R N-32 N-25 N- 9 Gartner Banana

ENGINE SPEED SENSING POWER STEERING N STEERING GEAR AND LINKAGE Removal / Installation 1. Turn the wheels to the straight-ahead position. 2. Loosen the wheel lug nuts. 3. On level ground, jack up the front of the vehicle and support it on safety stands. 4. Remove the wheels. Note Turning the steering wheel while the steering gear is removed will make reinstallation difficult. Do not turn the steering wheel while the steering gear is removed. If the steering wheel is turned in that condi- tion, the clockspring connector may have to be adjusted. (Refer to section T.) 5. Remove in the order shown in the figure, referring to Removal Note. 6. With the wheels in the straight-ahead position, install in the reverse order of removal. 7. Tighten all necessary bolts and nuts to the specified torque. 8. After installation: (1) Check for fluid leakage. (Refer to page N-22.) (2) Bleed air from the system. (Refer to page N-21.) (3) Adjust the front wheel alignment. (Refer to section R.) 1. Cotter pin 5. Pressure pipe 2. Nut ~emovai Note ............... page N-26 3. Tie-rod endlsteering knuckle 6. Return hose Removal Note ............... page N- 7 7. Mounting bracket bolt 4. Bolt 8. Steering gear and linkage Gartner Banana

P BRAKE SYSTEM Installation note Disc pad 1. Push the piston inward by using the 2. Install the new pads in the mounting SST. support. 1 I 15UOPX-030 Removal I lnstallation (Caliper) 1. On level ground, jack up the front of the vehicle and support it with safety stands. 2. Remove the wheels; then remove components in the order shown in the figure. 3. Install in the reverse order of removal. 4. Tighten all nuts and bolts to the specified torques, referring to the figure. 1. Brake hose 5. Shim 2. Connecting bolt 6. Bolt 3. Caliper 7. Mounting support Disassembly / Inspection / 8. Disc plate Assembly .................. page P-28 Inspection ................... page P-27 4. Disc pad ................... Inspection page P-27 Gartner Banana

BRAKE SYSTEM ADJUSTING BRAKE PADS Installation note Manual adjustment gear 1. Turn the manual adjustment gear clockwise until the brake pads just touch the disc plate. -1 2. Return the manual adjustment gear counterclockwise 113 turn. Removal 1 lnstallation (Caliper) 1. On level ground, jack up the rear of the vehicle and support it with safety stands. 2. Remove the wheels; then remove components in the order shown in the figure, referring to Removal Note. 3. Install in the reverse order of removal, referring to lnstallation Note. 4. Inspect all parts and repair or replace as necessary. 5. Tighten all nuts and bolts to the specified torques, referring to the figure. Parking brake cable Removal I Inspection 1 Installation ................. page P-36 Connecting bolt Brake hose Plug Manual adjustment gear Removal Note ............... page P-29 Installation Note ................. above Lock bolt 7. Caliper Disassembly I Inspection 1 Assembly .................. page P-32 8. Disc pad Replacement ................ page P-29 Inspection ................... page P-31 9. Bolt 10. Mounting support 11. Disc plate Inspection ................... page P-31 Gartner Banana

ANTILOCK BRAKE SYSTEM (ABS) ABS WHEEL SPEED SENSOR (FRONT) Removal 1 Inspection / Installation 1. Removal in the order shown in the figure. 2. Install in the reverse order of removal. I. Connector 2. Bolts 3. Bolt 4. Wheel speed sensor lnspection . . . . . . . . . . . . . . . . . . . . . . . below Inspection Wheel speed sensor 1. Measure resistance between terminals of the wheel speed sensor. Resistance: 1 .&I .2 kQ 2. If not as specified, replace the wheel speed sensor. Gartner Banana

ANTILOCK BRAKE SYSTEM (ABS) ABS WHEEL SPEED SENSOR (REAR) Removal 1 Inspection I Installation 1. Remove the filler pipe protector (left side). 2. Remove the spare tire (right side). 3. Remove in the order shown in the figure. 4. Install in the reverse order of removal. 1. Connector 2. Mud guard 3. Bolts 4. Wheel speed sensor lnspection . . . . . . . . . . . . . . . . . . . . . . . below lnspection Wheel speed sensor 1. Measure resistance between terminals of the wheel speed sensor. Resistance: 1 .O-1.2 kR 2. If not as specified, replace the wheel speed sensor. Gartner Banana