1994 MAZDA MX-5 window

s WINDOW REGULATOR, GLASS, AND GUIDE Inwardloutward adjustment of door glass 1. Loosen the window regulator lower installation nuts and the glass guide lower installation nut. 2. Move the window regulator and glass guide inward or outward so that the upper and side edges of the door glass are in the correct position. 3. Tighten the installation nuts. Tightening torque: 22-27 Nem (2.2-2.8 kgfsm, 16-20 ftelbf) OUT TOO GLASS CORRECT POSITION SEC. A-A IN TOO FAR GLASS GUIDE SEC. B-B NUT NUT RETAINER MOUNTING HOLE No.5 TAINER MOUNTING HOLE No.1 / RETAINER MOUNTING HOLE No.1 I I TAINER CONVERTIBLE TOP DETACHABLEHARDTOP I 1 -1 E MOUNTING HOLE No.7 ETAINER MOUNTING HOLE No.8 // RETAINER MOUNTING HOLE ~o.6* RETAINER I GLASS @ RETAINER GLASS SEC. F-F SEC. E-E mm (in) Gartner Banana

WINDOW REGULATOR, GLASS, AND GUIDE s Forward/backward adjustment of door glass 1. Loosen the window regulator upper installation nuts and the glass guide upper installation nut. 2. Move the window regulator and glass guide forward or backward so that the side edge of the door glass u is in the correct ~osition. 3. Tighten the installation nuts. Tightening torque: 22-27 N-m (2.2-2.8 kgf-m, 16-20 ft-lbf) AHEAD TOO FAR CORRECT POSITION SEC. B-B GLASS GUIDE CONVERTIBLE TOP DETACHABLE HARDTOP RETAINER MOUNTING HOLE No.5 ~OUNTING HOLE NO.^ RETAINER MOUNTING HOLE NO.^ RETAINER / RETAINER GLASS GLASS SEC. E-E SEC. F-F mm (in) Gartner Banana

WINDOW REGULATOR, GLASS, AND GUIDE After completion of adjustment 1. Verify the following with the weatherstrip removed: (1) When the door glass is raised, the lower glass stoppers contact the upper glass stoppers simulta- neously. (2) The door glass is in the correct position when fully closed. 2. Verify the following with the weatherstrip installed: (1) he door glass raises and lowers smoothly with the door closed. (2) Alignment of the weatherstrip is correct (convertible top only). CONVERTIBLE TOP RETAINER MOUNTING HOLE No.1 RETAINER MOUNTING HOLE N0.5 15 {0.59) 60 (2.36) / RETAINER MOUNTING HOLE No.7 RETAINER MOUNTING HOLE No.8 DETACHABLE HARDTOP RETAINER MOUNTING HOLE No.1 15 (0.59) 65 i2.56) RETAINER G'LASS SEC. E-E RETAINER 16 (0.62) RETAINER MOUNTING HOLE No.5 4(0.94) 9.4 + 2.0 9.3 + 2.0 10.37 i 0.08) (0.37 * 0.08) 9.1 2 2.0 7.4 2 2.0 10.36 0.08) (0.29 k 0.08) I c d SEC. F-F mm {in) 45UOSX41 Gartner Banana

POWER WINDOW SYSTEM s POWER WINDOW SYSTEM STRUCTURAL VIEW 1. Rear console 3. Power window regulator Removal 1 Installation ....... page S-56 Removal / Installation ........ page S- 9 ................. 2. Power window switch Inspection page S-22 Removal / Installation ....... page S-56 Inspection ................. page S-22 S-I 9 Gartner Banana

POWER WINDOW SYSTEM TROUBLESHOOTING Circuit Diagram MAIN FUSE BLOCK e (EI /I \ IX-021 OFF SWITCH FUSE BLOCK K POWER WINDOW SWITCH CLOSE OPEN POWER WINDOWS POWER WINOOW REGULATORS l., -03 POWER WINDOW REGULATOR RH(OR2) -01 POWER WINDOW SWITCH(1) K-02 POWER WiNCOW REGULATO2 LH (ORI) Gartner Banana

POWER WINDOW SYSTEM Power windows do not operate w Turn ignition switch ON B+: Battery positive voltage Check P.WINDOW (30A) fuse W Shon circuit Disconnect power window main switch connector, check Repair harness (Main switch--Ground) continuity of terminal-wire (B) to ground Check for B+ at terminal-wire (BNV) of power window main switch connector 1 Check power window switch (Refer to page S-22) 1 45UOSX-016 One power window does not operate w --c NG' I Turn ignition switch ON I Repair harness (Fuse box-Main switch) Check for B+ at terminal-wires of power window main Check power window switch (Refer to page S-22) switch connector Up : (GIR), ((RIB)) wire Down: (G), ((RIG)) wire I Repair harness (Main switch-Motor) connector Up : G/R) wire Down: [G) wire Check power window regulator (Refer to page S-22) (( )): Passenger side Gartner Banana

s POWER WINDOW SYSTEM FDB POWER WINDOW SWITCH Inspection 1. Check for continuity between terminals of the switch with an ohmmeter. O--O: Indicates continuity 2. If not as specified, replace the switch. POWER WINDOW REGULATOR lnspection 1. Connect battery positive voltage to terminal A and L' ground terminal B of the motor connector. Verify that the motor operates. 2. Reverse the above connections and check for reverse operation of the motor. 3. If not as specified, replace the motor. Gartner Banana

MOLDING AND GARNISH s MOLDING AND GARNISH COMPONENTS Removal / Installation 1. Remove in the order shown in the figure, referring to Removal Note. 2. Install in the reverse order of removal. 1 REPLACE P REPLACE 1. Windshield molding 4. Beltline molding ............. Installation Note ........... page S-28 Removal Note page S-28 2. Cowl grille 5. Rear window molding (detachable hardtop) ....... ........... Removal I Installation page S-44 Installation Note page S-29 3. Front beltline molding 6. Rear finisher ............. Removal Note ............. page S-28 Removal Note page $28 Gartner Banana