1994 MAZDA MX-5 lock

ENGINE SPEED SENSING POWER STEERING N STEERING GEAR AND LINKAGE Removal / Installation 1. Turn the wheels to the straight-ahead position. 2. Loosen the wheel lug nuts. 3. On level ground, jack up the front of the vehicle and support it on safety stands. 4. Remove the wheels. Note Turning the steering wheel while the steering gear is removed will make reinstallation difficult. Do not turn the steering wheel while the steering gear is removed. If the steering wheel is turned in that condi- tion, the clockspring connector may have to be adjusted. (Refer to section T.) 5. Remove in the order shown in the figure, referring to Removal Note. 6. With the wheels in the straight-ahead position, install in the reverse order of removal. 7. Tighten all necessary bolts and nuts to the specified torque. 8. After installation: (1) Check for fluid leakage. (Refer to page N-22.) (2) Bleed air from the system. (Refer to page N-21.) (3) Adjust the front wheel alignment. (Refer to section R.) 1. Cotter pin 5. Pressure pipe 2. Nut ~emovai Note ............... page N-26 3. Tie-rod endlsteering knuckle 6. Return hose Removal Note ............... page N- 7 7. Mounting bracket bolt 4. Bolt 8. Steering gear and linkage Gartner Banana

ENGINE SPEED SENSING POWER STEERING N 1. Oil pipe lnspect for clogging and damage 2. Tie-rod end ................ u Disassembly Note below lnspect ball joint for damage and malfunction 3. Locknut (Tie-rod end) 4. Boot clamp 5. Boot wire 6. Boot lnspect for cracks and other damage 7. Housing cover 8. Locknut (Pinion shaft) 9. Tie rod ............ Disassembly Note page N-28 .............. Assembly Note page N-32 lnspect for bending lnspect ball joint for damage and malfunction 10. Washer 11. Locknut (Adjusting cover) 12. Adjusting cover .............. Assembly Note page N-32 13. Plate 14. Yoke spring lnspect for weakness and damage 15. Support yoke lnspect for damage and wear 16. Dust cover lnspect for cracks and other damage - 17. Retaining ring 18. Pinion shaft assembly ............ Disassembly Note page N-28 ................... Inspection page N-29 .............. Assembly Note page N-31 19. Plug assembly ............ Disassembly Note page N-28 .............. Assembly Note page N-31 20. Upper bearing lnspect for wear, damage and malfunction 21. Oil seal 22. O-ring 23. Plug 24. Snap ring 25. Control valve .............. Assembly Note page N-31 26. Seal ring 27. O-ring 28. Seal ring 29. Pinion shaft 30. Mounting bracket and mount 31. Stop ring 32. Steering rack assembly ............ Disassembly Note page N-28 .............. Assembly Note page N-30 33. Holder .............. Assembly Note page N-30 lnspect for wear and damage 34. O-ring 35. Y-packing 36. Seal ring 37. O-ring 38. Steering rack lnspect for cracks, damage and wear 39. Oil seal ............ Disassembly Note page N-28 .............. Assembly Note page N-30 40. Backup ring ............ Disassembly Note page N-28 .............. Assembly Note page N-30 lnspect for cracks and other damage 41. Lower bearing ............ Disassembly Note page N-29 lnspect for wear, damage and malfunction 42. Oil seal ............ Disassembly Note page N-29 .............. Assembly Note page N-29 43. Spacer ............ Disassembly Note page N-29 lnspect for cracks, damage and wear 44. Center bearing Disassembly Note ............ page N-29 .............. Assembly Note page N-29 lnspect for wear, damage and malfunction 45. Mounting bracket 46. Mount 47. Gear housing lnspect for cracks and other damage 25UONX-020 Disassembly Note Tie-rod end Mark the tie rod, locknut and tie-rod end for proper reas- sembly. Gartner Banana

N ENGINE SPEED SENSING POWER STEERING 7. Attach the SST to the pinion and install the plug assem- bly. Adjusting cover 1. Tighten the mounting bracket in a vise. 2. Set the rack to the center position. 3. Tighten the adjusting cover to 4.9 N.m (50 kgf.cm, 43 in4bf) with the SST three times, then return it 25". 4. Apply sealant to the threads of the locknut. 5. Attach the locknut. 6. Measure the pinion torque by using the SST and a pull scale. Standard Center of rack + 90": 1 .O-1 .I N-m {I 0-1 2 kgf-cm, 8.7-1 0.4 in-lbf) ii Scale reading: 1 .&I .2 kg (2.2-2.64 Ib) 7. If not within specification, repeat steps 3 through 6. 8. Install the locknut. Tightening torque: 59-74 N.m (6.0-7.5 kgf.m, 44--54 ftdbf) Hermetic sealing inspection 1. Connect the SST to the power cylinder section of the gear housing. 2. Apply 53.3 kPa (400 mmHg, 15.7 inHg) vacuum with a vacuum pump and verify that it is held for at least 30 seconds. 3. If the vacuum is not held, replace the oil seal. Tie rod 1. Secure the rack gear in a vise, and tighten the tie rods with the wrench. Tightening torque: 79-98 N.m (8.0-10.0 kgf-m, 58-72 ft-lbf) 2. Align the washer with the rack groove, and crimp the washer. Gartner Banana

N ENGINE SPEED SENSING POWER STEERING Disassembly Note Oil pump Use the SSTwhen securing the oil pump in a vise, so that force is not applied to the pulley or shaft. Inspection Pump body front, rear lnspect the front and rear of the pump body for cracks and damage, and the friction surface of the rotor for wear. Replace the pump assembly if a problem is found. Cam ring, rotor, blade, side plate 1. lnspect the blade friction surface of the cam ring for wear. 2. lnspect the pump body of the rotor and side plate friction surface for wear. 3. lnspect the cam ring friction surface of the blade for -, wear. 4. lnspect clearance between the rotor and blade. Control valve, spring 1. lnspect the control valve for cracks, damage and block- age, and the friction surface for wear. 2. lnspect the spring for damage. Assembly Note Rotor Install the rotor with the indentification mark facing upward. Gartner Banana

Before beginning any service procedure. refer to section T of this manual for air bag system service warnings and audio antitheft system alarm conditions . BRAKING SYSTEM INDEX ....................................... P- 2 OUTLINE ..................................... P- 4 SPEClFlCATlONS ........................... P- 4 BRAKE SYSTEM ............................. P- 5 PREPARATION ............................. P- 5 TROUBLESHOOTING GUIDE ................ P- 6 AIR BLEEDING ............................. P- 7 BRAKE HYDRAULIC LINE ................... P- 7 BRAKE FLUID .............................. P- 8 ............................. BRAKE PEDAL P- 9 MASTER CYLINDER (STANDARD) ............ P-11 MASTER CYLINDER (ABS) .................. P-14 POWER BRAKE UNIT ....................... P-20 PROPORTIONING BYPASS VALVE ........... P-23 FRONT BRAKE (DISC) ...................... P-25 CALIPER ................................... P-28 REAR BRAKE (DISC) ........................ P-29 CALIPER ................................... P-32 PARKING BRAKE SYSTEM .................... P-34 TROUBLESHOOTING GUIDE ................ P-34 PARKING BRAKE LEVER .................... P-34 PARKING BRAKE CABLE .................... P-36 ANTILOCK BRAKE SYSTEM (ABS) ............ P-37 DESCRIPTION .............................. P-37 PREPARATION ............................. P-37 TROUBLESHOOTING GUIDE ................ P-38 CIRCUIT DIAGRAM ......................... P-52 HYDRAULIC UNIT ........................... P-53 ........................ ABS CONTROL UNIT P-55 RELAYS .................................... P-56 ABS WHEEL SPEED SENSOR (FRONT) ....... P-58 ABS SENSOR ROTOR (FRONT) .............. P-59 ABS WHEEL SPEED SENSOR (REAR) ........ P-60 ABS SENSOR ROTOR (REAR) ............... P-61 25UOPX-001 Gartner Banana

INDEX P ANTILOCK BRAKE SYSTEM (ABS) 1. Hydraulic unit 5. ABS sensor rotor (front) Removal / Installation ......... page P-53 Removal / Ins~ection / ................. Disassembly / Assembly ...... page P-54 Installation page P-59 2. ABS control unit 6. ABS wheel-speed sensor (rear) Removal I Installation ......... page P-55 Removal 1 Inspection I ................. 3. Relays Installation page P-60 Removal / Inspection / 7. ABS sensor rotor (rear) ......... ................. w Installation page P-56 Removal / Inspection page P-61 .................. 4. ABS wheel-speed sensor (front) Installation page P-62 Removal / Inspection / ................. Installation page P-58 Gartner Banana

BRAKE SYSTEM P BRAKE SYSTEM PREPARATION - SST Wrench, flare nut 49 0221 600C Expand tool, disc brake 49 8043 001 Adjust gauge 49 8043 004 Wrench, socket Gauge, oil pressure (Part of 49 U043 OAO) - 49 U043 006 Hose (Part of 49 U043 OAO) For removal and installation brake PIPS For installation of disc pads 49 F043 001 Adjust gauge For Adjustment of push rod clearance For adjustment of push rod clearance 49 0208 701 A Boot air out tool For adjustment of push rod clearance For inspection of brake fluid pressure For removal of piston seal 49 8043 003 Lock tool, turning For inspection of brake fluid pressure For adjustment of push rod clearance 49 U043 OAO Gauge set, oil pressure & - For inspection of brake fluid pressure 49 U043 005 Joint (Part of ,-, 49 U043 OAO) For inspection of brake fluid pressure Gartner Banana

BRAKE SYSTEM P CLEARANCE BRAKE PEDAL On-vehicle Inspection Pedal height Verify that the distance from the center of the upper surface of the pedal pad to the carpet is as specified. Pedal height: l7l-l8l mm (6.93-7.13 in} (With carpet) Adjustment 1. Disconnect the stoplight switch connector. 2. Loosen locknut@ and turn switch @ until it does not con- tact the pedal. 3. Loosen locknuts @I and turn rod 0 to adjust the height. 4. Adjust the pedal free play and tighten operating rod lock- nuts @I. 5. Turn the stoplight switch until it contacts the pedal; then turn an additional 1 /2 turn. Tighten the locknuts. Tightening torque: 14--18 N.m (1.4--1.8 kgf-m, 10-13 ft-lbf) 6. Connect the stoplight switch connector. 7. Verify that the stoplight operates correctly. Pedal play 1. Depress the pedal a few times to eliminate the vacuum in the system. 2. Lightly depress the pedal by hand until resistance is felt, and check the free play. Free play: 4--7mm (0.16-4.28 in) Adjustment 1. Loosen locknuts @I and turn rod to adjust the free play. 2. Check the pedal height and verify that the stoplight switch operates correctly. Tightening torque: 24--34 N.m (2.4--3.5 kgf-m, 17-25 ft-lbf} Pedal-to-floor clearance 1. Verify that the distance from the floor panel to the center of the upper surface of the pedal pad is as specified when the pedal is depressed with a force of 589 N (60 kgf, 132 Ibf}. Pedal-to-floor clearance: 95mm (3.74 in} (Without carpet) 2. If the distance is less than specified, inspect for air in the brake system. Gartner Banana