1994 MAZDA MX-5 turn signal

FUSE SPECIFICATIONS Main Fuse Block u I Fuse Amperes Protected circuit HEAD INJ MAIN BTN 30A 30A COOLING FAN (AD FAN) 1 ABS I 60A I Antilock brake svstem I Headlight relay, Headlight switch Alternator, Diagnostic module (for air bag system) 80A 40A ST SIG RETRACTOR Fuse Box No.1 Except circuits protected in main fuse block: INJ 30A, HEAD 30A, RETRACTOR 30A TNS relay, Headlight switch 30A 20A EGI main relay, Coolant fan relay A/C relay 10A 30A Park l Neutral switch, Circuit-opening relay Retractable headlight actuator Fuse ENGINE METER (POWER WIND) Amperes 15A WIPER TAIL ROOM I 10A I PCME, Key reminder switch, Audio unit I Protected circuit EGI main relay, Coolant fan relay 15A 30A STOP HAZARD CIGAR 15A I Cigarette lighter, Audio unit 1 Instrument cluster, Turn signal switch, Timer and buzzer unit, Cruise control main switch Power window switch 20A 15A Fuse Box No.2 Blower switch, Wiper switch Taillights, Side marker lights, License plate lights, Parking lights 15A 15A Fuse Amperes Protected circuit I Stoplight switch, Horn switch, Cruise control unit Flasher unit Fuse Color Code (DEFOG) (ANTENNA) I Fuse amperes I Color code Fuse type 25UOTX-013 20A 20A I I 10A Red 1 I Rear window defroster Power antenna Plate type 15A 20A Light blue Yellow 30A 30A 80A Light green Pink Black Cartridge type Gartner Banana

RELAY T RELAY STRUCTURAL VIEW 1. Headlight relay 2. TNS relay 3. Retractable headlight relay 4. EGI main relay 5. Circuit-opening relay 6. Rear window defroster timer unit 7. Coolant fan relay 8. Horn relay 9. Flasher unit 10. Rear window defroster relay DESCRIPTION The DRL control unit (Canada only) controls the operation of the turn signal lights. When the ignition switch is at ON or START, the front turn signal lights illuminate as running lights, except when one of the following switches is on: Headlight switch. Turn signal light switch. Hazard warning switch. Parking brake switch. Gartner Banana

RELAY TIMER a 45UOTX-01 FLASHER UNIT Inspection 1. Turn the ianition switch to ON. RETRACTABLE HEADLIGHT RELAY Inspection 1. Disconnect the relay. 2. Apply battery positive voltage and check for continuity .- between terminals of the relay. B+: Batterv ~ositive voltaae Step -- -- M: Continuity Terminal A I H I G I B I D 1 2 3. If not as specified, replace the relay. 2. Operate the following switches and check the operation of the turn signal and hazard warning lights. 0 0 3. If not as specified, troubleshoot the circuit., 0 Switch Turn signal switch Hazard warning switch HAZARD WARNING SW - - 0 Procedure Right side ON Left side ON ON 0 B+ Operation Right turn signal lights flash Left turn signal lights flash All turn signal lights flash 0 GND V Gartner Banana

T SWITCH 1 FLASHER UNlT TR CRUISE CONTROL UNlT u Inspection 1. Disconnect the negative battery cable. 2. Remove the knee protector. 3. Disconnect the combination switch connector. i 4. Check for continuity between the terminals described by using an ohmmeter. 5. If the continuity is not as specified, replace the combina- tion switch as an assembly. Lights, dimmer, and passing switch Position Low beam Headlight High beam Passing Tail, Parking W: Continuity Turn signal switch Terminal E I HL I HU (TNSJHEADI BA I B I Switch m: Continuity Left Right Windshield wiper and washer switch O--O : Continuity d Terminal 0 0 Cruise control switch FU I TL TR 0 0 I Position SETICOAST RESUME/ACCEL Terminal SE I RE W: Continuity 0 E 0 0 0 ,i Gartner Banana

T LIGHTING SYSTEM Troubleshooting 1 Symptom: Turn and hazard warning function do not operate. I Step 1 Check HAZARD 15A fuse and METER 15A fuse in the fuse block. Step 2 Measure voltage at terminal H (B/R) of the flasher unit connector. Fuse Burnt OK Action Replace fuse after checking and repairing wiring harness Go to Step 2 Step 3 1. Disconnect the flasher unit connector. 2. Check for continuity between terminal A (B) of the flasher unit connector and ground. B+: Battery positive voltage -1 Voltage B+ Other Continuity Step 4 1. Turn the ignition switch ON. 2. Set the turn signal switch ON (right or left) and measure voltage at terminal C (G/Y) and terminal B (G/R) of the combination switch connector (&pin connector). Action Go to Step 3 Repair wiring harness (Hazard fuse - Flasher unit) Action Yes No B+: Battery positive voltage I Terminal I Wire IVoltaae 1 Action I Reconnect connector and go to Step 4 Repairing wiring harness (Flasher unit - GND) C - u (w) ,, .,. I (ti~nl - B+ Others B+ , Others I lnspect combination switch Go to Step 5-1 Inspect combination switch Go to Ster, 5-2 d Gartner Banana

LIGHTING SYSTEM J 45UOTX-116 2. Set the turn signal switch to the left position and measure voltage at terminal E (G/R) of the flasher unit connector. Step 5 1. Set the turn signal switch to the right position and mea- sure voltage at terminal F (GN) of the flasher unit con- nector. B+: Battery positive voltage Voltage B+ Other Action Turn the ignition switch OFF and go to Step 6 Repair wiring harness (Combination switch - Flasher unit) B+: Battery positive voltage Voltage B+ Other Step 6 1. Remove the hazard warning switch. 2. Check for continuity between terminal H(B) of the hazard warning switch connector and ground. 2. If correct, reconnect connector and go to Step 8. 3. If not as specified, replace the hazard warning switch. Action Turn the ignition switch OFF and go to Step 6 Repair wiring harness (Combination switch - Flasher unit) Continuity Yes No Step 7 1. Check for continuity between terminals of the hazard warning switch. Step 8 1. Disconnect the flasher unit connector. 2. Check for continuity between terminal C(0) of the flasher Actlon Go to Step 7 Repair wiring harness (Hazard warning switch connector - GND) Switch OFF ON unit and ground. W: Continuity Terminal I Yes Turn off the hazard warning switch and go to I Continuity F 0 0 B 0 Action D 0 No Repair wiring harness (Flasher unit - Hazard warning switch) Gartner Banana

T LIGHTING SYSTEM FRONT TURN REAR TURN Step 9 1. Reconnect connector and turn the ignition switch to ON. 2. Set the turn signal switch to the right position and mea- sure voltage at terminal G(G/W) of the flasher unit con- -i nector. B+: Batterv ~ositive voltaae I Other I Replace flasher unit I Voltage 3. Set the turn signal switch to the left position and measure voltage at terminal D(G/B) of the flasher unit connector. Action B+: Battery positive voltage Alternates OV and B+ I Go to Step 10 I Voltage I Action I 1 Alternates OV and B+ 1 Go to Ste~ 10 1 I Other I Replace flasher unit I Step 10 1. Disconnect the turn signal light connectors. 2. Set the turn signal switch to the left or right position. 3. Measure the voltage at the terminals of the combination light connector. Light 1 Terminal I Voltage I I Alternates Front Alternates Front C (GIO) OV and B+ LH Alternates qyr I A (WB, I OV and B+ Ln I 1 Other - B+: Battery positive voltage Action I Go to Step 11 Go to Step 11 Go to Step 11 I Repair wiring harness (Flasher unit - Front combination liaht) Go to Step 11 I Repair wiring harness (Flasher unit - Rear combination light) 1. Turn the ignition switch to OFF. 2. Remove and check the bulbs. I Position I BUM I Action I Hazard warning 7 Hazard warning Bulb OK Burn OK Replace bulb Repair wiring harness (Front combination light - GND) Replace bulb Repair wiring harness (Rear combination light - GND) 4 Gartner Banana

LIGHTING SYSTEM T Symptom: Turn signals do not operate. (Hazard warning function operates normally.) J 45UOTX-I23 Step 1 Check the METER 15A fuse in the fuse block. Fuse 1 Action 1 I Burnt I Replace fuse after checking and repairing wirina harness I OK I GO to step 2 I Step 2 1. Turn the ignition switch to ON. 2. Measure voltage at terminal A(B/Y) of the combination switch connector. Other B+: Battery positive voltage Repair wiring harness (TURN fuse - Combination switch) Voltage B+ Step 3 Set the turn signal switch to ON (right or left) and mea- sure voltage at terminal C (GN) and terminal B(G/R) of the combination switch connector (&pin connector). Action Go to Step 3 B+: Battery positive voltage Terminal I Wire IVoltage 1 Action inspect combination switch (Refer to Daae T-20) Gartner Banana