1994 MAZDA MX-5 SECTION T

s FRONT BUMPER FRONT BUMPER COMPONENTS Removal 1 Installation 1. Raise the headlights. 2. Disconnect the negative battery cable. 3. Remove in the order shown in the figure. 4. Install in the reverse order of removal. Front combination light 6. Set plate Removal .................... Section T 7. Front fascia Front side marker light 8. Retainer Removal .................... Section T 9. Bumper reinforcement 3. Fender bracket 10. Spacer 4. Mud guard 11. Front bumper retainer 5. Grille cover 12. Front bumper bracket Gartner Banana

REAR BUMPER s REAR BUMPER COMPONENTS L Removal 1 Installation 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear side marker light 2. Splash shield Removal . . . . . . . . . . . . . . . . . . . . Section T 3. Rear bumper Gartner Banana

s MOLDING AND GARNISH Removal Note Front beltline molding Remove the outside mirror to remove the front beltline molding. (Refer to page S-34.) i/ Rear finisher Remove the rear combination light to remove the rear finisher. (Refer to Section T.) PRIMER 45UOSX42C I MOLDING I MOLDING Beltline molding Remove the convertible top to remove the beltline mold- ing. (Refer to page S-67.) Installation Note Windshield molding 1. Remove the windshield. (Refer to page S-44.) 2. Install the windshield. (Refer to page S-44.) 3. Apply primer with a brush to the bonding area of the new upper molding. Keep the bonding area free of dirt and -- grease, and do not touch the surface. Allow the primer to dry for approximately 30 minutes. 4. Align the center mark in the molding with the glass mark (0) 5. Install the upper portions of the molding into the body (Q) . 6. Push the corner of the molding into the body ((3). 7. Push the side portions of the molding into the body, beginning from the bottom (@). 8. Check for water leaks. If a leak is found, wipe the water off well and repeat the installation. Hardening time of repair sealant Time required until car Temperature Surface hardening time ,, be put into service 5°C (41 OF) Aoorox. 1.5 hr 12 hr I 35°C {95"F} I Approx. 10 rnin 2 hr 1 Gartner Banana

WINDSHIELD WIPER AND WASHER Wlper does not operate in Lo or Hi position 1 B+: Battery positive voltage - Check WIPER 20 A fuse Short circuit Turn ignition switch ON I OK 1 I Checkfor B+ at terminal-wire windphieldwiper.witchu Repair harness (Fuse box - Switch) 1 I connector I I I OK Check for B+ at terminal-wires (UR) and (VW) of switch connector with switch, as shown Lo : VW) B+ Hi : [uR) s+ Check windshield wiper switch (Refer to Section T) I 1 OK Check for continuity of motor terminal-wire (B) to ground Repair brush plate holder (Refer to page S-43) 1 Check for B+ at terminal-wi-(VR) Repair (UW) or (UR) wire harness 1 Check wiper motor (Refer to page 538) motor connector with switch, as shown Lo: VW) B+ Hi : [UR) B+ Wiper automatic park function does not work 1 (Switch-Wiper motor) Turn ignition switch ON t Repair harness (Fuse box - Wiper motor) Check wiper motor (Refer to page S-38) Gartner Banana

WINDSHIELD WIPER AND WASHER Intermittent function does not operate L I B+: Battery positive voltage Check for continuity of m Repair brush plate holder (Refer to page S-43) Oy Check windshield wiper switch (Refer to Section T) 45UOSX-036 Wiper continues to operate when switch is OFF Check windshield wiper switch (Refer to Section T) One-touch function does not operate Check windshield wiper switch (Refer to Section T) Washer does not operate (Wiper operates OK) L O5uoSX-050 Washer continues to operate when switch is OFF 1 Turn ignition switch ON Check windshield washer switch (Refer to Section T) Check for B+ at terminal-wire (UO) of windshield washer Check windshield washer switch (Refer to Section T) switch connector with washer switch ON I o5UosX-052 Check for B+ at terminal-wire (UO) of washer motor con- Repair harness (Switch - Motor) nector with washer switch ON I OK I I NGr I I Disconnect washer motor 2-pin connector; check for conti- Repair harness (Motor - Ground) nuity of terminal-wire (B) to ground Check washer motor (Refer to page S-38) 45UOSX-037 Gartner Banana

s WINDSHIELD WIPER AND WASHER WITH ABS A B WIPER MOTOR lnspection Check for continuity between the terminals with the wiper in parked position. Terminals A-B A-C A-D WASHER MOTOR lnspection Connect battery positive voltage to terminal A and a ground to terminal 6, and verify that the motor operates. Continuity NO Check operation by applying battery positive voltage and a ground to the terminals of the motor connector. B+: Battery positive voltage FRONT WIPER AND WASHER SWITCH lnspection Refer to Section T. Yes Yes Terminal B+ A Terminals B-C Operation speed Low Continuity NO B-D C-D No Yes Gartner Banana

DASHBOARD AND CONSOLE DASHBOARD AND CONSOLE COMPONENTS Removal l Installation 1. Disconnect the negative battery cable. Warning Handling the air bag module improperly can accidently deploy the air bag, which may seri- ously injure you. Read SERVICE WARNINGS, section T, before handling the air bag module. 2. Remove in the order shown in the figure, referring to Removal Note. To remove the dashboard, remove the control wires of the heater unit and blower unit. 3. Install in the reverse order of removal. 1. Ashtray 2. Change lever knob 3. Rear console assembly a. Back plate b. Shift lever boot 7. Speedometer cable 8. Instrument cluster 9. Center louver Removal Note ............. page S-57 10. Center an el assemblv c. Power window switch Removal Note ............. page S-58 d. Cover (Without power window) 1 1. Glove box assembly e. Console lock assembly 12. Passenger-side airbag module (if equipped) 4. Center lower panel assembly Removal 1 Installation ......... section T Removal Note ............. page S-57 13. Hood release knob -1 5. Steering shaft 14. Center hole cover 6. Meter hood assembly 15. Side cover Removal Note ............. page $57 16. Dashboard Gartner Banana

FLOOR COVERING FLOOR COVERING COMPONENTS Removal / Installation 1. To remove the cabin carpet, first remove the following: a Seats (Refer to page S-65.) b Dashboard (Refer to page S-56.) c Heater unit (Refer to Section U) d Front side trim, scuff plates, quarter trim, and rear package trim (Refer to page S-59.) e Front seat belts and buckles (Refer to page S-63.) 2. Remove the remaining parts in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear end mat 2. Foot rest 3. Bracket 4. Cabin carpet Gartner Banana