Page 376 of 1708
J TRANSMISSION Extension Housing Parts Disassemble in the order shown in the figure. REPLACE 1. Steel ball, spring, and spring cap 8. Change bushing 2. Select-lock spindle, spring, and spring cap 9. Wave washer 3. Plug, spring, and pushpin 10. Change control case 4. Blind cover 11. Rod cover 5. Roll pin 12. Oil passage 6. Control rod 13. Oil seal 7. Control rod end Do not remove unless necessary Gartner Banana
Page 380 of 1708
J TRANSMISSION ASSEMBLY Precaution 1. All O-rings and gaskets must be replaced with the new ones included in the overhaul kit. 2. Before assembly, make sure all parts are completely clean. 4 3. Assemble the parts within 10 minutes after applying sealant. Allow all sealant to cure at least 30 minutes after assembly before filling the transmission with transmission oil. 35UOJX-053 (5TH) (REVERSE) (~RD, 4TH) (1 ST, 2ND) 45UOJX-029 Clutch hub For the synchronizer assemblies, align the synchronizer ring grooves and synchronizer keys. The synchronizer rings can be distinguished as shown in the figure. The inner diametes of the 2nd synchronizer ring is larger than the 1 st. When installing the gears and clutch hub assemblies in the following procedure, make sure that they are installed in the direction shown in the figure. Gartner Banana
Page 381 of 1708
TRANSMISSION J Extension Housing Parts Assemble in the order shown in the figure, referring to Assembly Note. 1. Oil seal 8. Control rod end Assembly Note .............. page 5-28 9. Roll pin 2. Oil passage Assembly Note .............. page J-28 3. Rod cover 10. Blind cover Assembly Note .............. page J-28 11. Plug, spring, and pushpin w 4. Change control case 12. Select-lock spindle, spring, and spring cap 5. Wave washer Assembly Note .............. page J-28 6. Change bushing 13. Steel ball, spring, and spring cap 7. Control rod Gartner Banana
Page 382 of 1708
J TRANSMISSION Assembly note Oil seal 1. Apply the specified oil to a new oil seal. 2. Install the new oil seal by using the SST. Rod cover 1. Apply transmission oil to the rubber bushings on the rod cover. 2. Install the rod cover with the mark facing forward. L I 35UOJX-058 Roll pin Install a new roll pin into the control rod end. The split in the roll pin must be facing in the direction shown in the figure. L I 45UOJX-031 Select-lock spindle, spring, and spring cap 1. Install the select-lock spindle, spring, and spring cap. Tightening torque: 7.9-10.7 Nm (80-11 0 kgfan, 70-95.4 in-lbf) 2. Push the select-lock spindle down by pushing on the control rod. This will ensure that the steel ball correctly engages the select-lock spindle. 45UOJX-032 Gartner Banana
Page 385 of 1708
TRANSMISSION J Mainshaft Parts Assemble in the order shown in the figure, referring to Assembly Note. WPPLY SPEwim OIL To IwiviDwL PmTs 45UOJX-034 Clutch hub Synchronizer key Clutch hub sleeve Synchronizer key springs Mainshaft 2nd gear Assembly Note .............. page J-32 2nd synchronizer ring Double cone Inner cone Synchronizer assembly (2nd) Clutch hub assembly (Istf2nd) Assembly Note .............. page J-32 3rd gear Assembly Note .............. page J-32 3rd synchronizer ring Clutch hub assembly (3rdl4th) Assembly Note .............. page J-32 Snap ring Assembly Note .............. page J-32 1 st synchronizer ring Bearing race Assembly Note .............. page J-32 Bearing Assembly Note .............. page J-32 1 st gear Assembly Note .............. page J-32 5-31 Gartner Banana
Page 397 of 1708

TRANSMISSION J 1. Oil seal Assembly Note .................. below 2. Snap ring u 3. Steel ball 4. Speedometer drive gear 5. Snap ring 6. Transmission case 7. Extension housing Assembly Note .................. below 8. Main drive gear bearing Assembly Note .................. below 9. Snap ring 10. Countershaft front bearing Assembly Note .............. page J-44 11. Snap ring 12. Adjustment shim Assembly Note .............. page J-44 13. Gasket 14. Front cover 15. Speedometer driven gear 16. Neutral switch 17. Back-up light switch 18. Boot 19. Clutch release fork Assembly Note .............. page J-44 20. Clutch release collar Assembly Note .............. page J-44 35UOJX-020 Assembly note Oil seal 1. Apply transmission oil to the outer periphery. 2. lnstall a new oil seal with the SST. Extension housing 1. Apply sealant to the contact surfaces of the bearing housing and transmission case. 2. Align the inner shift lever and shift rod end groove, and install the extension housing. 3. Apply sealant to the bolt threads, and install the bolts. Tightening torque: 18-26 N.m (1.8-2.7 kgf.m, l4--19 ft4bf) Main drive gear bearing Install the main drive gear bearing by using the SST, and secure it with a new snap ring. Gartner Banana
Page 399 of 1708
TRANSMISSION J INSTALLATION 1. On level ground, jack up the vehicle and support it evenly on safety stands. 2. Install in the order shown in the figure, referring to lnstallation Note. L 3. Add the specified amount of the specified transmission oil. (Refer to page J-8.) 4. Warm up the engine and transmission, and inspect for oil leakage and transmission problems. 1. Transmission 7. Exhaust pipe Installation Note ............. page J-46 8. Performance rod 2. Power plant frame (PPF) 9. Differential mounting pipe Installation Note ............. page J-46 10. Undercover 3. S~eedometer cable 11. Shift lever w 4. ~iarter Installation Note ............. page J-47 5. Clutch release cylinder 12. Rear console 6. Propeller shaft 13. Shift lever knob Service ...................... section L Gartner Banana
Page 400 of 1708

J TRANSMISSION -=DIFFERENTIAL MOUNTING SPACER 45UOJX-054 Installation note Transmission 1. Tilt the engine by pushing up on the front of the oil pan with a wooden block and a transmission jack. d 2. Support the transmission with a transmission jack. 3. Raise the transmission into place and install and tighten the installation bolts. Tightening torque: 64-89 N-m (6.5--9.1 kgf-m, 48-65 ft.lbf) Power plant frame (PPF) 1. Install the differential mounting spacer. Tightening torque: 38-51 N.m (3.8-5.3 kgf-m, 28-38 ft-lbf) 2. Support the transmission with a jack so that it is level. 3. Position the PPF and tighten the transmission-side bolts by hand. 4. Verify that the sleeve is installed into the block. 5. Install the spacer and reamer bolts in the forward hole, then hand tighten them. 6. Snugly install the power plant frame bracket. 7. Tighten the transmission-side bolts. Tightening torque: 104-123 N-m (10.S12.6 kgf.m, 76.7-91.1 ft.lbf) 8. Tighten the differential-side bolts. Tightening torque: 104-1 23 N-m (1 0.S12.6 kgf.m, 76.7-91.1 ft-lbf) Gartner Banana