1994 MAZDA MX-5 light

REAR BUMPER s REAR BUMPER COMPONENTS L Removal 1 Installation 1. Disconnect the negative battery cable. 2. Remove in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear side marker light 2. Splash shield Removal . . . . . . . . . . . . . . . . . . . . Section T 3. Rear bumper Gartner Banana

s MOLDING AND GARNISH Removal Note Front beltline molding Remove the outside mirror to remove the front beltline molding. (Refer to page S-34.) i/ Rear finisher Remove the rear combination light to remove the rear finisher. (Refer to Section T.) PRIMER 45UOSX42C I MOLDING I MOLDING Beltline molding Remove the convertible top to remove the beltline mold- ing. (Refer to page S-67.) Installation Note Windshield molding 1. Remove the windshield. (Refer to page S-44.) 2. Install the windshield. (Refer to page S-44.) 3. Apply primer with a brush to the bonding area of the new upper molding. Keep the bonding area free of dirt and -- grease, and do not touch the surface. Allow the primer to dry for approximately 30 minutes. 4. Align the center mark in the molding with the glass mark (0) 5. Install the upper portions of the molding into the body (Q) . 6. Push the corner of the molding into the body ((3). 7. Push the side portions of the molding into the body, beginning from the bottom (@). 8. Check for water leaks. If a leak is found, wipe the water off well and repeat the installation. Hardening time of repair sealant Time required until car Temperature Surface hardening time ,, be put into service 5°C (41 OF) Aoorox. 1.5 hr 12 hr I 35°C {95"F} I Approx. 10 rnin 2 hr 1 Gartner Banana

WINDSHIELD CENTER I SPACER mrn (in) 46UOSX-05( I REPAIR SEALANT mrn {i~ GLASS SEC. A-A % rnrn {in) 45UOSX-052 I V NOTCH GLASS MARK a 4. Securely bond a new dam along the circumference of the glass 7 mm i0.28 in) from the edge. Allow it to dry completely. - 5. Install the spacers onto the body as shown. If a spacer is damaged, replace it. 6. Prepare the nozzle of the sealant tube so that it has a flange that can run along the edge of the glass and a V from which the sealant can flow. Once the primer is dry, apply repair sealant (BOO1 77 739) around the entire cir- cumference to fill the gap between the dam and the edge of the glass with a ridge of sealant 11 mm I0.43 in} high. Keep the bead of sealant smooth and even, reshaping it where necessary with a spatula. 7. If a protector is damaged, securely bond a new protector onto the body as shown. Allow it to dry completely. 8. Install the glass, aligning the glass mark with the V notch in the spacer. Push it in lightly toward the vehicle to corn- press the sealant. 9. To prevent the glass from being pushed out by air pres- sure if a door is closed, open all of the windows until the repair sealant has hardened. Hardening time of repair sealant I Temperature I Surface hardening time ( Time required until car can be PU~ into service I I I 5°C (41 OF) I Approx. 1.5 hr I 12 hr 20°C (68°F) 35°C (95°F) Approx. 1 hr Approx. 10 min 4 hr 2 hr Gartner Banana

s REAR WINDOW GLASS mm {in) I 45UOSX-059 1 , REPAIR SEALANT mm (in) " GLASS UPPER PROTECTOR SEC. A- SIDE PROTECTOR I LOWER PROTECTOR I 45UOSX461 STUD REPAIR SEALANT / 4. Securely bond a new dam along the circumference of the glass 8 mm (0.31 in) from the edge. Allow it to dry completely. i/ 5. Prepare the nozzle of the sealant tube so that it has a flange that can run along the edge of the glass and a V from which the sealant can flow. Once the primer is dry, apply repair sealant (8001 77 739) around the entire cir- cumference to fill the gap between the dam and the edge of the glass with a ridge of sealant 11 mm (0.43 in) high. Keep the bead of sealant smooth and even, reshaping it where necessary with a spatula. 6. If a protector is damaged, securely bond a new protector onto the detachable hardtop as shown. Allow it to dry completely. 7. Align the studs of the glass with the detachable hardtop and mount the glass. 8. Push the glass lightly toward the front to compress the sealant. 9. Tighten the glass mounting nuts. Tightening torque: 2.4--3.3 N-m (24--34 kgf-cm, 20.9-29.5 in-lbf) 10. Use a scraper to smooth away any sealant that oozes out. Add more sealant to any points of poor contact. 11. Install the new rear window molding. (Refer to page S-29.) Hardening time of repair sealant I Temperature I Surface hardening time I Time required until car can be out into service I 8 20°C (68°F) I Approx. 1 hr I 4 hr I I 35°C {95"F) 1 Approx. I0 min I 2 hr I d I I 5°C I41 OF) I Approx. 1.5 hr 12 hr Gartner Banana

BODY ELECTRICAL SYSTEM ................................... INDEX T- 2 ........................... SWITCHES T- 2 FUSES AND RELAYS .................. T- 3 .............................. LIGHTS T- 4 CRUISE CONTROL SYSTEM ........... T- 5 ...................... AUDIO SYSTEM T- 6 SRS AIR BAG SYSTEM ................ T- 7 ............................... OUTLINE T- 8 TROUBLESHOOTING GUIDE ........... T- 8 ELECTRICAL SYMBOLS ............... T- 9 ................................... FUSE T- 10 STRUCTURAL VIEW ................... T- 10 ...................... SPECIFICATIONS T- 11 ........................ DESCRIPTION T- 12 ....................... REPLACEMENT T- 12 ....................... RELAY .. ....... T- 13 STRUCTURAL VIEW ................... T- 13 ........................ DESCRIPTION T- 13 RETRACTABLE HEADLIGHT RELAY .... T- 14 ....................... FLASHER UNIT T- 14 ........................... TNS RELAY T- 15 .......................... HORN RELAY T- 15 COOLANT FAN RELAY ................. T- 15 REAR WINDOW DEFROSTER RELAY ... T- 16 HEADLIGHT RELAY ................... T- 16 ................................ SWITCH T- 17 ................... STRUCTURAL VIEW T- 17 ........................ DESCRIPTION T- 17 .................... IGNITION SWITCH T- 18 COMBINATION SWITCH ............... T- 19 RETRACTOR SWITCH AND HAZARD WARNING ............................. SWITCH T- 21 ................. INSTRUMENT CLUSTER T- 22 ................... STRUCTURAL VIEW T- 22 ........................ DESCRIPTION T- 22 .................... CIRCUIT DIAGRAM T- 23 ................. TROUBLESHOOTING T- 24 ............ REMOVAL / INSTALLATION T- 29 ........... DISASSEMBLY 1 ASSEMBLY T- 29 ...................... SPEEDOMETER T- 30 ........................ TACHOMETER T- 30 WATER TEMPERATURE GAUGE ....... T- 30 ......................... FUEL GAUGE T- 31 OIL PRESSURE GAUGE ............... T- 31 .................... PRINTED CIRCUIT T- 32 VEHICLE SPEED SENSOR ............. T- 32 WATER TEMPERATURE SENDER UNlT . T- 32 FUEL GAUGE SENDER UNlT ...................... (IN FUEL TANK) T- 32 OIL PRESSURE SENSOR .............. T- 33 ............... SPEEDOMETER CABLE T- 33 WARNING LIGHT AND SENDER UNIT ..... T- 34 ................... STRUCTURAL VIEW T- 34 CIRCUIT DIAGRAM .................... T- 35 ................. TROUBLESHOOTING T- 36 BRAKE FLUID LEVEL SENSOR ......... T- 39 PARKING BRAKE SWITCH ............. T- 39 ..................... BUCKLE SWITCH T- 39 ...................... LIGHTING SYSTEM T- 40 ................... STRUCTURAL VIEW T- 40 ......................... HEADLIGHTS T- 41 ......................... STOPLIGHTS T- 53 TURN AND HAZARD WARNING LIGHTS . T- 57 ..................... BACK-UP LIGHTS T- 66 TAILLIGHTS. SIDE MARKER LIGHTS. PARKING LIGHTS AND LICENSE PLATE LIGHTS . T- 69 DAYTIME RUNNING LIGHTS (DRL) .................... (CANADA SPEC.) T- 72 ........... REAR COMBINATION LIGHT T- 76 .................... INTERIOR LIGHTS T- 78 ................ ILLUMINATION LIGHTS T- 82 .................................. HORN T- 84 ................... STRUCTURAL VIEW T- 84 .................... CIRCUIT DIAGRAM T- 85 ................. TROUBLESHOOTING T- 86 ............ REMOVAL 1 INSTALLATION T- 87 ............ REAR WINDOW DEFROSTER T- 89 ................... STRUCTURAL VIEW T- 89 ........................ DESCRIPTION T- 89 ................. TROUBLESHOOTING T- 90 ................ REPAIRING FILAMENT T- 93 ............. CRUISE CONTROL SYSTEM T- 94 ................... STRUCTURAL VIEW T- 94 .................... CIRCUIT DIAGRAM T- 95 ................. TROUBLESHOOTING T- 96 ....... SELF-DIAGNOSTIC INSPECTION T-100 ............... CRUISE CONTROL UNIT T-103 .................... ACTUATOR CABLE T-104 ..................... CLUTCH SWITCH T-105 .......... STOP LIGHTIBRAKE SWITCH T-105 ...... CRUISE CONTROL MAIN SWITCH T-106 ........... CRUISE CONTROL SWITCH T-106 ............. VEHICLE SPEED SENSOR T-106 ........................... ACTUATOR T-107 a .................................. AUDIO T-108 ................... STRUCTURAL VIEW T-108 ................... SYSTEM DIAGRAM T-109 ............................ FEATURES T-110 FUNCTION AND OPERATING ......................... PROCEDURE 1-111 ............. OPERATION DESCRIPTION T-113 .................. ANTITHEFT SYSTEM T-120 ................. TROUBLESHOOTING T-122 ............ REMOVAL I INSTALLATION T-145 .................... POWER ANTENNA T-149 ......................... INSPECTION T-153 CONNECTOR TERMINAL .................... SPECIFICATIONS T-154 SRS AIR BAG SYSTEM .................. T-156 PREPARATION ........................ T-156 ................... STRUCTURAL VIEW T-156 .......... COMPONENT DESCRIPTION T-157 SYSTEM DIAGRAM ................... T-158 ................. SERVICE WARNINGS T-159 GENERAL PROCEDURES ............. T-160 TROUBLESHOOTING ................. T-160 DRIVER-SIDE AIR BAG MODULE ....... T-206 PASSENGER-SIDE AIR BAG MODULE . . T-207 DIAGNOSTIC MODULE ................ T-208 CLOCK SPRING ....................... T-209 CRASH SENSOR (D-SENSOR) ......... T-210 CRASH SENSOR (S-SENSOR) ......... T-213 AIR BAG MODULE DISPOSAL . .. PROCEDURE ........................ T-215 INSPECTION OF SST (DEPLOYMENT TOOL) ............... T-217 Gartner Banana

T INDEX INDEX SWITCHES 1. Ignition switch 8. Brake switch Inspection ................ page T- 18 Removal / Installation ...... page T-105 Replacement ............. page T- 18 Inspection ................ page T-105 2. Combination switch adjustment ............... page T-105 Removal / Installation ...... page T- 19 9. Back-up light switch Inspection ................ page T- 20 Inspection ................ page T- 68 3. Retractor switch 10. Door switch Removal / Installation ...... page T- 21 Inspection ................ page T- 81 Inspection ................ page T- 21 11. Interior light switch 4. Hazard warning switch Troubleshooting ........... page T- 79 Removal / Installation ...... page T- 21 12. Panel light control switch Inspection ................ page T- 21 Inspection ................ page T- 83 5. Parking brake switch 13. Horn switch Inspection ................ page T- 39 Removal / Installation ...... page T- 88 6. Buckle switch 14. Clutch switch Inspection ................ page T- 39 Removal / Installation ...... page T-105 7. Stoplight switch Inspection ................ page T-105 -/ Adjustment ............... page T- 56 Adjustment ............... page T-105 Inspection ................ page T- 56 15. Rear window defroster switch Removal 1 Installation ......... section U T-2 Gartner Banana

INDEX T FUSES AND RELAYS 1. Main fuse block 7. Rear window defroster timer unit Replacement ............... page T-12 8. Coolant fan relay .................. 2. Fuse box No.1 and No.2 Inspection page T-15 Replacement ............... page T-12 9. Horn relay .................. 3. Headlight relay inspection page T-15 .................. Inspection page T-16 10. Flasher unit .................. 4. TNS relay Inspection page T-14 .................. Inspection page T-15 11. Rear window defroster relay u .................. 5. Retractable headlight relay Inspection page T-15 .................. Inspection page T-14 6. EGI main relay ................... Inspection section F Gartner Banana

T INDEX LIGHTS 1. Retractable headlight 7. Back-up light Aiming ..................... page T-50 Removal / Installation ... page T-68 Removal I Installation ........ page T-49 8. License plate light 2. Retractable headlight actuator Removal / Installation ... page T-71 Inspection .................. page T-51 9. Side marker light 3. Stoplight Removal / Installation ... page T-71 Removal / Installation ........ page T-55 10. Taillight 4. High-mount stoplight Removal / Installation ... page T-71 Removal / Installation ........ page T-55 11. Rear combination light 5. Turn and hazard warning light Removal / Installation ... page T-49 d Removal I Installation ........ page T-64 Disassembly / Assembly pages T-76,77 6. Parking lights 12. Interior light Removal / Installation ........ page T-71 Gartner Banana