1994 JAGUAR XJ6 AUX

E I ect r ica I
15.4.7 SYMPTOM FLOW CHARTS
The following test procedures are designed to test the system as a whole, identifying faulty areas and indicating poss- ible solutions by functional operations.
During all test procedures the entry
/ exit mode switch must be OFF.
The first three test procedures listed i.e. drivers seat position adjustments, steering column position adjustments, rear
view mirror position adjustments must be carried out four times, each time under one of the conditions stated below:
Key in ignition barrel
Ignition key in auxiliary position
Driver’s door open with ignition key out
Driver’s door closed within the last 30 seconds with ignition key out.
0
Driver‘s seat position adjustments
1.
2.
3.
0
4.
5.
6.
7.
0
Locate seat switch pack on the side of the seat cushion.
Operate the fore
/ aft movement control switch. Does the seat respond in the correct
manner?
Yes: Proceed to step 3.
No:
Operate front and rear, raise / lower movement control switches. Does seat respond in the
correct manner in each case?
Yes: Proceed to step 4.
No:
Operate squab recline / incline movement control switch. Does squab respond in correct
manner?
Yes: Proceed to step 5.
No:
Operate lumbar pump inflate / deflate control switch. Does lumbar pad stiffen and slacken
according
I y?
Yes: Proceed to step 6
No:
Operate headrest raise / lower switch. Does headrest respond in correct manner?
Yes: proceed to step
7.
No:
Remove key from ignition, close driver‘s door and allow 30 seconds to elapse. Repeat
steps
1 - 6 and check that adjustment cannot be made.
Test complete; proceed to Memory Position Set.
Abort
test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Steering column position adjustments
1.
2.
Locate steering column joystick switch the LH side of the column.
Operate switch to give fore
/ aft movement. Does the column respond in correct manner?
Yes: Proceed to step 3.
No:
Operate the switch to give raise / lower movement. Does column respond in the correct
manner in each case?
Yes: Proceed to step 4.
No:
Remove key from ignition, close driver’s door and allow 30 seconds to elapse. Repeat
steps 1
- 3 and check that adjustment cannot be made.
Test complete; proceed to Memory Position Set.
Abort
test and refer to Diagnostic Sub
-Routines.
3.
Abort test and refer to Diagnostic Sub-Routines.
4.
5.
X300 EDM 15.4 - 13 Issue 1 August 1994

Rear view mirror position adjustments
1. Locate mirror select switch on driver's door switch pack and select driver's side mirror, ie
rotate switch towards the door.
2. Locate rear view mirror joystick switch on driver's door pack.
Operate the switch to give left
/ right and up / down movement. Does the mirror respond
in the correct manner?
3. Yes: Proceed to step 4 or 5.
No:
Japanese market vehicles only
Operate the switch to action 'fold away mode'. Does mirror respond in the correct manner
in each case?
Yes: Proceed to step
5.
No:
All markets
Operate mirror select switch to opposite position and repeat steps
1 to 4 for passenger side
mirror.
With ignition switched to auxiliary, select reverse gear and operate mirror joy
-stick
downwards. Does passenger side mirror dip automatically?
Yes: Proceed to step
7.
No:
Remove key from ignition, close driver's door and allow 30 seconds to elapse. Repeat
steps
1 - 6 and check that adjustment cannot be made.
Test complete; proceed to Memory Position Set.
Abort
test and refer to Diagnostic Sub
-Routines.
4.
Abort test and refer to Diagnostic Sub-Routines.
5.
6.
Abort test and refer to Diagnostic Sub-Routines.
7.
8.
Memory set position - drivefs side
1.
2.
3.
4.
5.
6.
7.
8.
Position the entry / exit switch, located on the LH side of the steering column, to off and
insert the key in the ignition.
Operate switches to position column, mirrors and seats to preferred positions.
Select 'memory' on the driver's door switch pack. Check that switch illuminates.
Depress desired memory button,
1,2 or 3, on door switch pack within 4 seconds of
memory select. Check that a chime sounds to confirm memory storage.
Operate the switches
so that memorized positions are changed. Depress relevant memory
option button,
1,2 or 3 and check that all positional settings are restored as memorized.
Remove key from ignition, close all doors and allow
30 seconds to elapse. Repeat steps 1
to 4 and check that adjustment cannot be made.
Readjust settings so that memorized positions are changed, leave the vehicle and operate
remote memory recall by locking and unlocking using the remote transmitter. Use both
transmitters to check both memory positions. Check all positional settings are restored as
memorized.
Yes: Proceed to step
8.
No:
Test complete. Abort
test and refer to Diagnostic Sub
-Routines.
X300 EDM Issue 1 August 1994 15.4 - 14

Carry out the passenger seat position adjustments procedure below under each of the conditions stated below:
Key in ignition barrel
. Passenger's door open
. Passenger's closed within the last 30 seconds
0 . Auxiliary ON
Passenger seat position adjustments
1.
2.
3.
4.
5.
0
6.
7.
8.
Locate seat switch pack on the side of the seat cushion.
Operate the fore
/ aft movement control switch. Does the seat respond in the correct manner?
Yes: Proceed to step
3.
No:
Operate front and rear, raise / lower movement control switches. Does seat respond in the
correct manner in each case?
Yes: Proceed to step
4.
No:
Operate squab recline / incline movement control switch. Does squab respond in correct
manner?
Yes: Proceed to step
5.
No:
Operate lumbar pump inflate / deflate control switch. Does lumbar pad stiffen and slacken
accordingly?
Yes: Proceed to step
6
No:
Operate headrest raise / lower switch. Does headrest respond in correct manner?
Yes: Proceed to step
7.
No:
Remove key from ignition, close passenger's door and allow 30 seconds to elapse. Repeat
steps
1 - 6 and check that adjustment cannot be made.
Test complete; proceed to Memory Position Set
Abort
test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.
Memory
set position - passenger's side
1.
2.
0 3.
4.
5.
6.
7.
0
Insert the key in the ignition.
Operate switches to adjust seat to preferred positions.
Select 'memory' on the passenger's door switch pack. Check that switch surround
i I I um i nates.
Depress desired memory button,
1,2 or 3, on door switch pack within 4 seconds of
memory select. Check that
a chime sounds to confirm memory storage.
Operate the switches
so that memorized positions are changed. Depress relevant memory
option button,
1, 2 or 3 and check that all positional settings are restored as memorized.
Yes: Proceed to step
6.
No:
Remove key from ignition, close door and allow 30 seconds to elapse. Repeat steps 1 - 4
and check that adjustment cannot be made.
Test complete. Abort
test and refer to Diagnostic Sub
-Routines.
X300 EDM 15.4 - 15 Issue 1 August 1994

Electrical rl
Carry out the exit 1 entry mode procedure below under the conditions stated below:
. Key in ignition barrel
. Driver's door closed
. Auxiliary ON
. Park brake ON
. Gear selector in Park.
Exit 1 Entry Mode
1.
2.
3.
From the driver's seat, position the memory mode switch, located on the LH side of the
steering column, to auto.
Operate the seat, column and mirror switches to preferred driving position.
Note:
Remove key from ignition. Check that seat moves backwards and column tilts upwards
and away, creating maximum space for exit.
Yes: Proceed to step
4.
No:
Seat must be a minimum of 50mm from rear end stop.
Abort test and refer to Diagnostic Sub
-Routines.
4.
5.
3.
Refit key in ignition, open driver's door. Check that seat moves backwards and column tilts
upwards and away, creating maximum space for exit.
Yes: Proceed to step
5.
No:
Leave key in ignition and exit the vehicle, closing driver's door. Ensure that column and
seat return to driving position. Re-enter vehicle and ensure that column and seat move to
entry position. Close door and check that seat
/ column return to previously selected
driving positions.
Yes: Test complete.
No: Refer to Diagnostic Sub-Routines.
Abort
test and refer to Diagnostic Sub
-Routines.
Seat heaters (driver and passenger)
1.
2.
Turn ignition ON and locate heater select switch on the center console.
Operate the switch to initiate seat heating. Does the switch surround illuminate?
Yes: Proceed to step
3.
No:
Allow sufficient time for heater to take effect. Does seat heat level increase in all
designated areas?
Abort
test and refer to Diagnostic Sub
-Routines.
4.
5.
Yes: Proceed to step 4.
No:
Allow time span to exceed 12 minutes. Does switch surround light extinguish and heating
cease?
Yes: Proceed to step
5.
No:
Re-select heating, allow cycle to commence then operate switch again. Does switch
surround light extinguish and heating cease?
Yes: Test complete
No: Refer to Diagnostic Sub-Routines.
Abort
test and refer to Diagnostic Sub
-Routines.
Abort test and refer to Diagnostic Sub
-Routines.