AJ16 Engine Service Manual
Clean all component parts and check for wear or damage,
renew worn or damaged components as necessary.
Check
forwear and renewtheauxiliaryshaft bushes (1 Fig.
1) using Service
Tool 18G 1434 (2 Fig. 1).
. Lubricate all bearing shells. Refit all shells using 18G 1434.
CAUTION: Ensure that the oil feed holes are lined up with the holes in the bearing shell (1 Fig. 2).
. Fit the timing cover blanking plate to the timing cover. Fit and tighten the securing bolts.
Lubricate and fit the auxiliary shaft to the housing.
Lubricate and fit the thrust washer.
. Refit the auxiliary shaft snap-ring.
Fit a new oil seal to the rear of the shaft.
Fit and align the oil pump drive-plate to the auxiliary shaft.
. Apply sealant to the bolt securing the driveplate, fit and
tighten the bolt. See Service Materials in the Preliminary
Pages.
Refit the power assisted steering pump, see Section 10 in
the appropriate Vehicle Service manual.
Fit the new sprocket to the crankshaft.
Using a straight edge (2 Fig. 3). check the alignment of the
oil pump drive sprocket (1 Fig. 3). and the crankshaft
sprocket (4 Fig. 3).
Push back the lock tabs from one bolt securing the oil
pump drive sprocket, and remove the bolt.
. Rotate the sprocket. Push back the locktabs from the sec- ond bolt, and remove the bolt.
m Rotate the sprocket, push back the lock tabs and remove the remaining bolt.
. Remove the tab washer and drive sprocket.
Remove the shims (3 Fig. 3). Calculate the thickness of
shim(s) required for correct sprocket alignment.
Fit and tighten a dummy stud to the oil pump drive flange. Fit and align the shims to the flange. Fit and align the
sprocket.
Fit and align the new tab washer.
Fit and tighten the first sprocket securing bolt. Do not lock
over the tab washer at this stage.
m Rotate the sprocket for access.
. Fit and tighten the second sprocket securing bolt. Lock
m Rotate the sprocket for access.
= Remove the dummy stud.
. Rotate the sprocket for access.
Re-tighten the first securing bolt.
. Re-check the sprocket alignment.
= Re-adjust as necessary.
m Lubricate the newtiming chain and position thechain over
. Lubricate the oil pump drive chain.
. Fit the drive chain to the oil pump sprocket.
* Engage the drive chain to the crank sprocket.
Ensure that the drive chain ends are on the damper side of
If the alignment is incorrect, proceed as follows:
over the
tab washer.
Fit and tighten the third
sprocket securing bolt. Lock over the tab washer.
Lock over the tab
washer.
the auxiliary drive shaft and crankshaft sprocket.
the sprockets.
Fia. 1
I I // , I,
Fia. 2
i Fig. 3
Issue 1 August 1994 38
4.21 Timing Chain Tensioner, Upper, Renew
SRO 12.65.29
Remove the timing cover.
Remove the upper timing chain (6 Fig. 1).
Remove the flanged bolts (3 Fig. 1) securing the tensioner
Remove the pedestal / tensioner assembly and chain
Remove the tensioner pivot pin (2 Fig. 1) and remove the
Clean the pivot pin.
Fit a new tensioner to the pedestal and fit the tensioner
pivot pin. Secure the tensioner with the flanged bolts.
Align the damper to the tensioner and fit the damper/ten- sioner assembly to the engine.
Ensure that the damper does not foul the auxiliary shaft
sprocket.
Finally tighten the securing bolts.
Fit the new timing chain.
Re-position the upper tensioner and temporarily secure to
Renew the timing cover oil seal and refit the timing cover.
pedestal.
damper
(1 Fig. 1).
tensioner from the pedestal.
the upper dampers with an elastic band. 1 13 19 18 17
Fig. 1
41 Issue 1 August 1994
AJ16 Engine Service Manual
4.24 Auxiliary Shaft, Renew
SRO 12.10.30
Remove the timing cover.
. Remove the pulley woodruff key and remove the oil seal
spacer from the crankshaft.
. Remove the flanged bolts (3 Fig. 1) securing the tensioner
pedestal.
Remove the pedestal / tensioner assembly and chain
damper (1 Fig. 1).
. Remove the tensioner pivot pin (2 Fig. 1) and remove the
tensioner from the pedestal. Clean the pivot pin.
. Remove the flanged bolts (5 Fig. 1) securing the upper
static damper. Remove the damper (4 Fig. 1) and upper
timing chain (6 Fig. 1).
Remove the bolts (11 Fig. 1) securing the chain tensioner
and remove the assembly (17 Fig. 1).
Remove the power assisted steering pump assembly, see
Section 10 in the appropriate Vehicle Service manual
. Remove the pump drive coupling.
. Remove the flanged bolt (1 Fig.2) and the drive-plate (2 Fig. 2).
Using Service Tool JD 118, remove the auxiliary shaft rear
oil seal (3 Fig. 2) from its housing.
. Using right-angled snap-ring pliers remove the snap-ring (5 Fig. 2) securing the drive shaft (4 Fig.2).
. Lift the timing chain (8 Fig. 1) from the sprocket (7 Fig. 11, remove the shaft / sprocket assembly and retrieve the
thrust washer.
. Clean all component parts and checkfor wear or damage.
Renew worn or damaged parts as necessary. Clean the auxiliary bearing housing.
. Check for wear and if necessarychangethe auxiliaryshaft bushes.
. Refit the housing with new gasket. Fit and tighten the se-
curing bolts.
. Lubricate the shaft and refit the to the housing, engaging
the chain with the gear as it is fitted. Lubricate and fit the
thrust washer and secure with the snap-ring.
. Renew the auxiliary shaft rear oil seal, see Section 4.25.
. Refitthe power assisted steering pump assembly, see Sec-
. Refit the lower chain tensioner, see Section 4.22.
Refit the upper chain tensioner, see Section 4.21.
. Renew the oil seal (1 Fig. 3) and refit the timing cover.
tion
10 in
the appropriate Vehicle Service manual.
Fig. 1
Fig. 2
Fig. 3
Issue 1 August 1994 44
AJ16 Engine Service Manual
4.25
SRO 12.10.32
Auxiliary Shaft Rear Seal, Renew
* Remove the power assisted steering pump assembly, see
Section
10 in the appropriate Vehicle Service Manual.
. Remove the pump drive coupling.
Remove the flanged bolt (1 Fig.1) and the drive-plate (2
Using ServiceTool JD 118, remove the auxiliary shaft rear
Note: Under no circumstances must the plastic insert be
removed prior to fitting the seal.
* Using ServiceTool 18G 1469fit and fully seat the auxiliary
Refit the power steering pump drive-plate and secure with
Refitthe power assisted steering pump assembly, see Sec-
Fig. 1).
oil seal (3 Fig. 1) from its housing.
shaft oil seal.
its bolt.
tion
10 in the appropriate Vehicle Service Manual.
Fig.
1
Issue 1 August 1994 45
D
Drive belt tensions, xvi
F
Fau It diagnosis
Diagnostic procedures, 3
Introduction, 3
Foreword, iii
General description
Construction, 1
Cooling system, 2
Crankcase breather, 1
Cylinder head, 1
Lubrication system, 1
Supercharger, 2
S
Service data, xiii
Service materials, xii
Service operations
Check & adjust
Crankshaft end
-float, 27
Valve clearances, 10
Cylinder head, 16
Engine assy., 33
Oil pump, 52
Auxiliary shaft, 44
Auxiliary shaf? rear seal, 45
Camshaft, 7
Camshaft cover gasket, 9
Connecting rod bearings, 22
Crankshaft, 24
Crankshaft damper /pulley assy., 26
Crankshaft front oil seal, 28
Crankshaft rear oil seal, 29
Cylinder head casting, 19
Cylinder head gasket, 13
Drive-plate, 31
Flywheel, 30
Main bearings, 23
Oil filter head gasket, 46
Oil pan gasket, 47
Oil pick-up strainer, 49
Oil pressure relief valve, 50
Oil pump, 51
Oil pump pipe ‘0’ ring, 48
Pistons &connecting rods, 20
Timing chain damper, 40
Timing chain tensioner
Overhaul
Renew
Lower,
42
Upper, 41
Timing chain, gear & tensioner, 37
Timing sprocket, Intermediate, 43
Transmission adapter plate, 32
Service procedures
Sealants, 2
SPS joint control system, 2
Service tools & equipment iv
T
Torque tightening specifications,
53
