1994 HONDA INTEGRA Page 98

Moonroof
Motor, Drain Tube and Frame Replacement
CAUTION: B€ caretul not to damag€ lhe seats, dash-
board and other interior trim.
1. Remove the glass (see page 2O-79) and headliner
(see page 20-98).
2. Disconnect the motor connector, and remove the
clips securing the ceiling light wire harness.
3. Remove the bolts and nuts, then remove the motor,
if necessarv,
NOTE: Make sure both sliders are parallel when in-
stalling the motor.


: 8olt, nut locationg
A

: Bolt, 2
6x1.Omm I9.8 N.m ILd tt.o kgf.-, I,.?- ", _,/
< : CliD locations. 2
CEILIING LIGHT
FRAME
B : Nut, 3
20-80
4.Disconnect the drain tubes.
Remove the bolts, then remove the trame from the
car.
NOTE: You may require assistance when removing
the frame.


: Eolt locations, I
6 x 1.0 mm
DRAIN TUBETo install, slide the draintube over the ftame nozzleat least 10 mm {O.4 in}.
6.
TUBE CI-IP
Pull the drain tubes out the front and rear pillars.
NOTE; Betore pulling out the drain tube, tie a string
to the end of it so it can be reinstalled.
Installation is the reverse ol the removal procedure.
NOTE:
a Clean the surtace of the frame.
a Check the trame seal.
a Check for water leaks.
7.
9.8 N.m (1.0 kgt m,7.2 rbr.ttl )
FRAME
FRONT

1.Remove the frame from the car {see page 2O-8O).
Remove the motor (see page 2O-8O).
Remove the drain channel.
NOTE: Take care not to damage, twist or lift theseat.
V : Screw locations, 2
DRAINCHAI{NEL
4. Remove the front drain
V : Clip locations, 2
channel on each side.
GUIDE RAIL
20-81
Glass Bracket/Slider, Lifter, Guide Rails and Cable Assembly Replacement
5. Remove the front rail holder on each side.
V : Nut, scrow locations
AV : f{ut, 2
b.
7.
Remove the anchor spring on each side.
Remove the nuts and screws, then lift and remove
both guide rails and cable assembly from the trame.
Remove the sunshade and both sunshade rails.
BV: Screw,
BV : Sciow, 4
V : Nut, rcrow locations
AV : Nut. 2
NOTE: To instalt, Iill thegtoove rn each grommet with sealant,
GUIDE RAIL
SUNSHADE

Opening Drag Check
(Motor Removedl
Betore installing the motor, measure the etfort required
to open the glass using a spring scale as shown.
CAUTION: When using a spring scale, protoct the
leading edg6 ot th€ glass with a shop towel.
lf load is over 40 N (4 kgt, 9lbf). check side clearance
and glass height adjustment (see page 2O-78).
Closing Force Check
(Motor Installedl
1. After installing all removed parts, have a hetper hotd
the switch to close the glass while you measure
torce required to stop it. Attach a spring scale asshown. Read the force as soon as the glass siops
moving, then immediately release the switch andspnng scare.
CAUTION: When using a spring scale, protoct tho
leading odge ol th€ glass with a shop towel.
200-290 N(20 - 30 kgf, rt4- 66 lbf)
lf the force is not within specification, install a new
lock washer, adjust the tension by turning the mo-
tor clutch adjusting nut, and bend the lock washer
against the motor clutch adjusting nut.
LOCKWASHERReplace.
'r coul{TER-cLocKwrsETo decrease
GLASS
\
20-83

Moonroof
lndex
Ssdan
GLASS BRACKETReplacement, page 20-88
SUNSHAOEReplacement, page
MOTORReplacement, page 20-87
('
/\FROi{T DRAIN TUBE
SLIDE STOPP€R LINK
SUNSHADE RAIL
GUIDE RAILReplacement, page 20-88
REAR DRAIN
V
\
e
FRONT ORAIN
REAR RAILHOLDER
SEAL
FRAMERepfacement, page 20-87
20-84
----/_--4
DRAIN CHANNEL

SymptomProbable Cause
Water leaks1. Clogged drain tube.
2. Gap between glass weatherstrip and roof panel.
3. Defective or improperly installed glass weatherstrip.
4. Gap between drain seal and roof panel.
Wind noise1. Excessive clearance between glass weatherstrip and root panel.
Motor noise1. Loose motor.
2, Worn gear or bearing,
3. Cable assembly deformed.
Glass does not move, but motor
turns
1. Clutch out of adjustment.
2. Foreign matter stuck between guide rail and slider.
3. lnner cable loose.
4. Cable assembly not attached properly.
Glass does not move and motor
does not turn {glass can be moved
with moonroof wrench)
1. Blown fuse.
2. Faulty switch.
3, Battery run down.
4. Defective motor.
5. Faulty relay.
Glass Height Adjustment
The roof panel should be even with the glass weather-
strip, to within 1.8 tO.5mm{O.O7 1O.O2 in} allthe way
around. lf not, slide the sunshade back, and:
Tilt-up the glass.
Loosen the bolts and adjust the glass.
Repeat on opposite side if necessary.
ROOF PANELGLASS ERACKET
GLASS WEATHERSTRIP
4. Side-to-side fit of glass weatherstrip can be adjust-
ed by loosening the frame mounting bolts and mov-
ing the frame right or lett and forward or backward
by hand (see page 20-87).
GLASS BRACKETForward
V : Eolt localions, 6
6x LOmm9.8 N.m 11.O kgf m,7.2 tbf.ttt
I
")
1.
2.
GLASS
4'/1210.5 mm lO.O7 1O.02 inl

Moonroof
Rear Edge Closing Adjustment
Open the glass about a foot, then close it to check where
rear edge begins to rise. It it rises too soon and seats too
tightly against the roof panel, or too late and does not
seat tightly enough, adjust it.
1. Remove the headliner (see page 20-1OO).
2. Remove the glass.
3. Remove the motor (see page 20-87).
4. Align the tilt-up position of the lifter on each side.
o.
5.
7.
Check that the alignment lett and right, then install
the motor.
Install the glass. then check for water leaks.
NOTE: Do not use high pressure water.
Install the headliner.
Glass and Sunshade Replacement
1. Open the sunshade.
2. Tilt-up the glass.
3, Remove the bolts, then remove the glass from the
glass bracket.
Using the moonroof
BOLTS6 x 1.O mm9.8 N'm lt O kgf m,
4.
5.
7.2 tbt.ftl
Remove the screws and lift the sunshade rails.
Silde the sunshade forward. then remove the
sunsnaoe.
SUlTSHADERAIL
Installation is the.everse ot the removal procedure.
Check for water leaks.
NOTE: Do not use high pressure water.
GLASS BRACKET
20-86

Motor, Drain Tube and Frame Replacement
CAUTION: Be carotul not to damago th€ seats, dash-
board and other int6rior trim,
1. Remove the glass (see page 2O-86) and headliner(see page 20-10O).
Disconnect the motor connector, and remove the
clips securing the ceiling light wire harness.
NOTE: To remove the motor, remove the screws.
Disconnect the drain tubes.
Loosen the front bolts.
Remove the bolts, then remove the trame from the
car.
NOTE:
a You may require assistance when removing the
trame.
a Take care not to bend the sunshade rails.
TUBECLIP
DRAIN TUBETo install, slade the drain tube ov6rthe frame nozzle at least 10 mm lO.4 in).
SUNSHADERAILS
Pullthe drain tubes out of the tront and rear oillars.
NOTE: Before pulling out the drain tube, tie a string
to the end of it so it can be reinstalled.
Installation is the reverse of the removal grocedure.
NOTE:
a Install the tube clips with the ends facing the side to easea Clean the surtace of the frame.
a Check the frame seal.
a Check for water leaks.
a Make sure the sunshade moves smoothlv.
SCREW
4.
\/
Make sure the sliders areparallel when installing themotor,
CONNECTOR
FRAME
BOLT6 x 1.0 mm9.8 N.m (1.O lg{.rn.7.2 tbt.ttl
Loosen the tront bohs
Fo?w!?d
tt.
FRONTDRAIN VALVES
installation of the headliner.
20-87

Moonroof
Remove the frame (see page 20-87).
Remove the drain channel.
NOTE: Take care not to damage, twist or litt the
seal.
4. Remove the motor (see page 20-87).
5. Remove the front drain channel.
6. Remove the nut, then remove the front rail holder.
9.8 N.m {1.O kgf.m,7 .2 tbt-lrl
9, Slide the glass bracket/slider, liJter backward, then remove it.
Glass Bracket/Slider, Lifter, Guide Rails and Cable Assembly Replacement -
1.
2.
3. Remove the screws, then remove the sunshade rail
by sliding it backward.
ITUT6xl.Omm9.8 t{.m {1.0 kgt.m,7.2 tbf.ttl
7. Remove the screws @ attsching the guide rail. then litt the guide rail.
8. Remove the nut. then remove the rear rail holder.
NOTE: Remove the anchor spring.
AI{CHOR
NUT6 x 'l.O mm
REAR RAILHOLDER
NOTE: Install the rear railthe sub-seal to the trame.
SUB-SEAL
holder, then glue
SUNSHADE RAIL
SCREW
20-88