1994 HONDA INTEGRA Bearings

Countershaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all parts with ATF belore reassembly.a Install the thrust needle bearings with unrolled edge of bearing retainer facing washer.a Inspect the thrust needle bearings and the needle bearings tor galling and rough movement.a Before installing the O rings, wrap the shaft splines with tape to prevent damaging the O-rings.a Locknut has left-hand threads.
CONICAL SPRINGWASHERReplace.
LOCKNUT {FLANGE NUTI23 x 1.25 mm1O3-0-lO3N.m{10.5-O-'l0.5ksf.m,75.9*O-75.9tbf.fr)Replace.Left-hand threads
REVERSE GEAR COLLAR
NEEDLE EEARINGPARKING GEAR
ONE.WAYCLUTCHREVERSEGEAR
BEVERSESELECTOR
REVERSE SELECTORHUB
4TH GEAR
NEEDLE BEARING
DISTANCE COLLAR,28 mmSelective part.
.I ST GEAR
NEEDLE EEARING
lST GEAR COLLAR
TRANSMISSIONHOUSING BEARING
COUNTERSHAFTCheck splines for excessivewear or damage.Check bearing surface for scoring,scratches or excessive wear_
2ND GEAE
THRUST NEEDLEBEARING
3RD GEAR
NEEDLE BEARING
THRUST NEEDLE BEARING
3RD GEAR COLLAR
3RD CLUTCH ASSEMBLY
O-RINGSReplace.

Sub-shaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all parts with ATF during reassembly.
a Install the thrust needle bearings with unrolled edge ot bearing retainer tacing washer.
a lnspect the thrust needle bearings and the needle bearings for galling and rough movement.
a Before installing the O-rings, wrap the shaft splines with tape to prevent dsmaging the O-.ings.
TRANSMISSIOI{ HOUSING
TRANSMISSIONHOUSING BEARING
6 x 1.0 mm12 N.m
lST-HOLD CLUTCHASSEMELY
O.RINGSReplace.
THRUST WASHER
THRUST NEEDLEBEARING
NEEDLE BEARING
4TH GEAR
THRUST I{EEDLEAEARIIIG
4TH GEAB COLLAR
NEEDLE EEARING
(1.2 kgf.m, 8.7 lbf.ft)
SUB.SHAFTCheck splines tor excessivewear or damage.Check bearing surlace torsconng. scratches or excessive
OIL GUIDE CAPReplace.NEEDLE BEARIT{GSTOPPER

Sub-shaft Bearings
Replacement
NOTE: Lubricate all parts with ATF before reassembly
'l . To remove the sub-shaft ball bearing trom the trans-
mission housing. expand the snap ring with snap ring
pliers, then push the bearing out using the special
tools and a Dress as shown.
ATTACHMENT, 62 x 68 mm07746-0010500
Remove the needle bearing stopper.
Remove the needle bearing from the transmisslon
housing using a drilt Punch.
DRIFT PUNCH
14-140
?A
SNAP RING
PRESS
Install the new needle bearing in the transmlsston
housing using the specialtools and a press as shown.
ATTACHMENT, 32 x 35 mm07746-0010100
Expand the snap ring with snap ring pliers, then in-
sert the ball bearing part way into the housing us-
ing the specialtools and a press as described in step
1. Installthe bearing with the groove facing outside
the housing.
Release the pliers, then push the bearing down into
the housing untilthe snap ring snaps in place around
rt.
After installing the ball bearing, verify the following:
a The snap ring is seated in the bearing and hous-
ing grooves.
a The snap ring ope.ates properly
a The ring end gap is correct.
5.
7.
END GAP: 0-7 mm

Torque Converter Housing Bearings
Mainshaft Beadng/Oil Seal Replacement
1 . Drive out or pull up the mainshaft bearing and oil seal,using the special tools as shown.
Slide HammerCommercially Available3/8 in. x 16
07749 -OOIOOOO
14-150
2.Drive in the new mainshaft bearing until it bottomsin the housing, using the special tools as shown.
3.Installthe new oil seal flush with the housing usingthe sDecial tools as shown.
ATTACHMENT,62x68mm07746-0010500
ATTACHMENT,72x75mm07746-0010600
DRIVEN

Transmission Housing Bearings
Mainshaft/Countershaft Bearing Replacement
1. To remove the mainshaft and counte.shaft bearingstrom the transmission housing, expand each snapring with snap ring pliers, then push the bearing outusing the special tools and a press as shown,
NOTE: Do not remove the snap rings unless it,snecessafy to clean the grooves in the housing.
ATTACHMENT,62x68mm
Io7746-
---7i
)
MAINSHAFT
Mainshaft Removal uaoiATTACHMENT-72 ,, 75 mmo7746-OOlO600
Counterrhaft Removal uao:ATTACHMENT,62x68mm07746-O010500
TRANSMISSIONt|oustitc
PRESS
14-152
SNAP BING
Expand each snap ring with snap ring pliers, insertthe new bearing pan-way into the housing using thespecialtools and a press as shown. Installthe bear-ing with the groove tacing outside the housing.
NOTE: Coat all parts with ATF.
Release the pliers. then push the bearing down intothe housing until the ring snaps in place around it,
DRIVERo7749-OOIOOOO
GnoovE
Mainshatt Inltallation us6:ATTACHMENT,72x75mm07746-0010600
Counto.shalt In3talldtion uso:ATTACHMENT.62x68mm07746-O010500
4.After installing the bearing verify the lollowing:
a The snap ring is seated in the bearing and hous-In9 grooves.
a The snap ring operates properly
a The ring end gap is correct.
END GAP: O-7 mm

NOTE: Check the ball bearings for wear and rough ro-
tation. It bearings are OK, removal is not necessary.
1. Remove the ball bearings using a standatd bearing
puller and bearing separator as shown.
BEARING PULLEB
BALL BEARING
Install new ball bearings using the special tool as
snown.
NOTE: Drive the bearings squarely until they bot-
tom against the carrier.
DRIVER, 40 mm l.D.07746-0030100
BALL BEARING
Bearing ReplacementOil Seal Removal
1.Remove the ditterential assembly.
Remove the 8O mm shim from the transmission
housing.
80 mm SHIM
TRA[{SMtSStONHOUSING
3. Remove the oilseal from the t.ansmission housing.
4. Remove the oil seal from the clutch housing,
OIL SEALR€plac6.
15-5

Tapered Roller Bearing Replacement
NOTE:
a The tapered roller bearing and bearing outer race
should be replaced as a set.
a Inspect and adjust the tapered roller bearing preload
whenevef the tapered rollef bearing is replaced.
a Check the tapered roller bearings tor wear and rough
rotation. lf tapered roller bearings are OK, removal is
not necessary.
1. Remove the tapered rolle. bearings using a bearing
puller and bearing separator as shown,
BEARING
BEARII{GSEPANATOR(Commercially
available)
Install new tapered roller bearings using the special
tool as shown.
NOTE: Drive the tapered roller bearings on until they
bottom against the differential carrier.
oilSealRemoval
1.Remove the differential assembly.
Remove the oil seal from the transmission housing.
3. Remove the oil seal from the clutch housino.
15-13

Differential (B18c1 eng:nel
Bearing Outer Race Replacement
CAUTION: Do not rous€ the thrust lhim and tho 79.8mm shim il tho outer rac6 was ddvon out.
NOTE;
a The bearing outer race and taper€d toller bearingshould be reDlaced as a set.a Inspect and adjust the tapered roller bearing proload
whenever th€ tapered roll€f bearing is roplac€d.
1 . Remove the oil seals from the transmission housing
and clutch housing (see page 15-13).
2. Remove the bearing outer raca, the thrust shim, andthe 79.5 mm shim from th€ transmission housing.
Remove the bearing outer racs and thrust shim tromthe clutch housing.
TRANSMtSStOl{ HOUStl{c
15-14
5. lnstall the oil sesl (see page 15-171.
4.Install the new thrust shim and 79.5 mm shim, then
drive the bearing outer races in the both housings
using the special tools as shown.
NOTE:
a Install the bearing outsr race squarely.a Check that there is no clearance between tha
bearing outer race, thrust shim, and transmission
housing.
BEARIl{GOUTER
07749-OOTOOOO
ONNERATTACHMENTOTttAD-PX/IOlOO