1994 HONDA INTEGRA belt

Timing Belt
lllustrated Index
NOTE:
. Refer to page 6-12 for positioning crankshaft and pulley before installing belt.
. Mark the direction of rotation on the belt before removing.
. Replace the rubber seals tor oil leakag€ between the cylinder head and cover.
a Do not uss the middle cover and lower cover for storing itsms disassembled.
. Clean the middle cover and lower cover before installation.
CAP NUT6xl.0mm9.8 N'm (1.0 kgf.m,7.2lbtft) WASHER
\oReplaco when damagedor deteriorated.
6x1.0mm
CYLINDER HEAD COVERRefer to pago 6-31 wheninstalling.
RUBBER SEALSReplace when damagedor deleriorsled.
BACK OOVER
lnstallwith concavesurface facing in.Clean.
8 x 1.25 mm37 N.m 13.8 kgl.m,27 lbf'ft)
AD.'USTING BOLT10 x t.25 mm5/r N.m 15.5 kgl.m, ,o lbtft)For adjustrnent only,do not r€move,
BOLT
COVER
6x1.0mm9.8 N'm (1.0 kg{.m. t.2 lbf.tt}
9.8 N,m 11.0 kg{.m,7.2 lbl.frl
Adlustment, pago 6-9Replacement, page 6"10
TIMIMi BELTInspection, page 6-9ALTERNATORBELTAdjustm6nt,Soction 23
CRANKSHAFTPULI"EYRomov6 any oiland clgaa on thgtiming bolt guideplato side.
TIMING BELTDBIVE PULLEYRemove any oiland clean,
LOWEnCOVER
lnstall with concavesurface facing out,Remove any oilano ctean.
NOTE: When installing a new crankshaft and/or new bolt:
O tighten the crankshaft pulley bolt to 196 N'm (20.0 kgf'm, 145 lbf'ft),
O loosen bolt,
O retighten it to 177 N.m (18.0 kgt.m, 130 lbf'ftl.
'14 x 1,25 mmlt7 t{.m 118.0 kgl.m, 130lbtftlReplacsmenl, page 6-8
6-7

Timing Belt
Inspection
Remove the cylinder head cover.
. Reler to page 6-3'l when installing.
Inspect the timing belt for cracks and oil or coolant
soaking.
NOTE:
. Replace the belt if oil or coolant soaked.
. Rsmove any oil or solvent that gets on the belt.
Rotate pulley
and inspscr bell.
After inspecting, retorque the crankshaft pulley bolt
to 177 N'm ('18.0 kgf'm, 130 lbt'ft).
Tension Adjustment
CAUTION: Always Ediust timing belt tonsion with tho
cngin. cold.
NOTE:
. The tensionet is spring-loaded to apply proper ten-
sion to the belt automaticallv after making the follow-
ing adjustment.
. Always rotate the crankshaft counterclockwise when
viewed trom the pulley side Rotating it clockwise
may result in improper adjustment ot the belt ten-
sion.
Remove the cylinder head cover. (Refer to page
6-31 when installing.)
Set the No. 1 piston at TDC (see page 6-12).
Rotate the c.ankshaft 5 - 6 revolutions to set the
bslt.
4. Set the No. I piston at TDC.
3.
ADJUSNNG BOLT54 N.m (5.5 kqf.m,a0 rbr.ftlFor adiustment only,do not remove,
5.
6.
7.
8.
Direction olrolatlon.
Loosen the adiusting bolt 1/2 turn (180') onlv
Rotate the crankshaft counterclockwise 3-teeth on
the camshaft pulley.
Tighten the adjusting bolt to the specified torque.
After adjusting, retorque the crankshaft pulley bolt
to 177 N.m (18.0 kgl.m. 130 lbf.ft).
6-9

Timing Belt
Removal
I
NOTE:
. Turn the crankshaft pulley so the No. 1 piston is attop d6ad center (TDC) before removing the belt (see
page &12).
a Inspect the water pump when removed the timingbolt {see page 10-9}.
1. Remove thawhe€lwell splash shield (see page 6-18).
2. Loosen ths adjusting bolt and mounting bolts, thenremove the power steering {P/S) pump belt.
MOUivNNG BOLTS8 x 1.25 mm2a N.m 12.4 kgf.m, 1 7 lbt frl
Loosen the adjusting bolt and idler pulley bracket
bolt, then remove the air conditioning (A,/C) com-
oressor belt.
IDLER PUI.IEY BRACKETBOLTl0 r 1.25 mma/a N.m {1.5 kgf.m.33 lbf'ft}
AA,USNNG
ADJUSTING
4, Loosen the adjusting nut and mounting nut, thenremove the alt€rnator belt.
EELTa,l N.m {4.5 kgl.m,33 lbfftl
Remove the cruise control actuator (see page 6-18).
Remove the sid6 sngine mount.
10 x 1.25 mm52 N.m {5.3 kgr'm,38 lbtft}Replace.
MOUNTING NUT10 x 1.25 mm
ADJUSNNG NUT8 x 1.25 mrr2a N.m l2.a lef.m,17 rbl.ftl
12 x 1.25 mm74 N.m 17.5 kgt m,s4 tb{.ftl

1.Remove the cylinder head cover.
. Refer to page 6-31 when installing.
Remove the Dulley bolt and crankshaft pulley (see
page 6-8).
Remove the middle cover and the lower cover.
NOTE:
. Do not use the middle cover and lower cover for
storing items disassembled.
. Clean the middle cover and lower cover before
installation.
CAP NUT 6 x 1.0 mm
10. Loosen the adjusting bolt 180'.
1'1. Push the tensioner to remove tension from the tim-
ing belt, then retighten the bolt.
12. Remove the timing belt from the pulleys.
NOTE: Push the tensioner pulley toloosen the belt.
8.
9.8 N.m 11.07.2 rbl.ftl
WASHER
orReplace when damaged
CYLINDEF HEADCOVERReter to page 6-31 wheninstalling.ADJUSTING BOLT10 x 1.25 mm54 N.m 15.5 kg{.m,/r0 lbf.ftlFor adjustment only,
TIMING BELTAdiustment, Page 6I
LOWEB @VER
MIDOLE COVER
6x1.0mm9.8 N.m 11.0 kgJ m, 7.2 lblftl
6x1.0mm9.8 N.m ('1.0 kgt.m,7.2 lbl fr)
Remove anY oiland clean
KE
6x1.0mm
NMING BELTGUIOE PLATElnstallwith concavesurface facing out.
and clean.CRANKSHAFT PULLEYRemove any oiland clean on ihetiming belt guideplate sido.9.8 N.m (1.0 kgtm,7.2lbt'ftl
6-11

Timing Belt
Installation
Install the timing belt in the revorce order of removal;
Only key points are described here,
NOTE: Cl€an the middle cover and lower cover beforeinstallation.
L Position the crankshaft and th€ camshaft pulleys asshown before installing the timing belt.
A. Set the crankshaft so that the No. 1 oiston is at
top dead center (TDC). Align the g.oovo on the
t€eth side of the timing belt d.ive pulley to the Opointer on the oil pump.
L Align the TDC marks on intake and exhaust pul-
tevs,
NOTE: To set the camshafts at TDC position for
No. 1 piston, align the holes in the camshafts
with the holes in No. l camshaft holders andinsert 5,0 mm pin punches in the holes.
PIN PUNCHES, 5.0 mm
2. lnstall the timing belt tightly in the sequence
snown.
O timing belt drive pulley {crankshaft) + @Adjusting pulley * @ Water pump pulley - @Exhaust camshaft pulley + @ Intake camshaft pul-
lev.
TDC mark align6d with thepointer on back cover,TDC MARK
6-12

Gylinder Head
Removal
I
t
Engine removal is not required for this procedure.
CAUTION: To avoid damaging tho cylinder head, wait
until tho ongino coolant temporature drops bolow 100"F
{38"C) beforo loo36ning the rotainin0 bolts.
NOTE:
. Inspect the timing belt before removing the cylinder
neao.
. Turn the crankshaft pulley so that the No. 1 piston is
at top dead center (TDCI (page 6-12).
. Mark all emissions hoses before disconnecting them.. Anti-theft radios have a coded theft protection circuit.
Be sure to get the customer's code number before.- Disconnecting the battery.- Removing the No. 32 (7.5 A) fuse irom the under-
hood fuse/relay box.- Removing the radio.
After service, reconnect oower to the radio and turn it
on.
When the word "CODE" is displayed, enter the cus-
tomer's 5-digit code to restore radio operation.
1. Disconnect the negative terminalfrom the battery.
2. Drain the engine coolant (see page 10-5).
. Remove the radiator cap to speed draining.
3. Relieve fuel pressure (see Section 1 1).
@ Do not smoke whils working on tusl
systom, keep opon flame or spark away trom work
area. Drain fuol only inlo an approvod containsr.
4. Disconnect the fuel feed hose.
SERVIC€ BOLT
WASHERSReplace.
5, Remove the intake air duct.
Remove the breather
evaporative emission
hose, water bypass hose and(EVAP) control canister hose.

Cylinder Head
Removal (cont'dlI
12.R€move the spark plug caps and distributor from
the cvlinder head.
Remove the upper radiator hose, heater hose and
water bypass hose.
UPPER RAI'IAYOR
14. Remove th6 solash shield.
WATER BYPASS
9.8 N.m {1.0 kgt m.t.2 tbr.frt
sHtEut
15. Remove the engine ground cable.
Remove the adjusting bolt and mounting bolts, then
remove the power steering (P/S) pump belt 8nd P/S
pump.
. Do not disconnect the P/S hoses.
6x1.0mmADJUSTINGBOLT9.8 N.m 11.0 tgfm,7.2 tbf.ftl
8 x 1.25 mm24 .m (2.akstm, 17lbf.ftl
P/S PUMP
Remov€ the air conditioning (Ay'Cl compressor(see pags 6-10).
R€move the alternator belt (see page 6-10).
Ramove the cruise control actuator.
8 x 1.25 mm2a N.m 12.4 kgt m,
belt
17.
t8
ACTUATOR

52 N.m (5.3 kgt'm, 38 lbf'ft)
19. Remove the side engine mount.
10 x 1.25 mm
20. Remove the cylinder head cover.
WASHERS
SIDE ENGINEMOUNT
12 x 1.25 mm74 N.m {7.5 kgf.m,5{ rbtftl
CYLINDEB HEAD
Remove the timing belt (see page 6-10).
Remove the camshaft pulleys and back cover.
23. Remove the exhaust manifold.
SELF.LOOKING NUT8 x 1.25 mm
BACK COVER
BRACKET
(cont'd)
6-19