1994 HONDA INTEGRA Ignition harness

PGM-FI System
Manifold Absolute Pressure
lFrom page 11-53)
{MAPI Sensor (cont'd)
(From paqe 1 1-53)
NO
M6asure voltage between D17{+) terminal and 021 (-}terminal.
ls there approx. 3 V?
Substituto 6 known{ood ECM.nd rach.ck. It symptom/indica-tion gooa away, Eplaco tho orlgi-nrl €CM.
Turn the ignition switch OFF.
Connect the test harness "D"
connector to the ECM only. not tothe main wire harness lsee page11-37).
Turn the ignition switch ON.
Measure voltage botwson Dl7(+) terminal and D21 {-}terminal.
R.p.lr opon or ahort in WHT|rELwi?o botw.on ECM {O17) and thoMAP senso..ls there approx. 5 V?
Substitute a known{ood ECMand rochsck. It prdcribed voltrgob now availablo, rophce trie origi-nal ECM.
approx. 3 v?
-D17 til D21 (-l
ooooooooooooo I oooooooo l l5oiE€tdl ooooooo
o oooo oooooooo ! ooooooooooooooooooo
11-54
'.---.-'

ECT SENSOR
GRN/BLU {-}
Turn the ignition switch ON.
Measure voltage betweon RED/WHT and body ground.
Measure voltage between RED/WHT {+}terminal and GRN/8LU(- ) terminal.ls there approx. 5 V?
ls there approx. 5 V?Ropai. opon in GRN/BLU wiro botwoon ECM(D221 and tho ECT36n3('r.Turn the ignition switch OFF.
Sub3tituto a known-good €CMand rochock. lf 3ymptom/indica-tion go6s away, roplaco the odgi-nal ECM.
Oisconnect the 22P connectortrom the Transmission ControlModule (TCM).
Turn the ignition switch ON.
ls there approx. 5 V7
Turn the ignition switch OFF andreconnect the connector to theTCM.
Connect the test harn€ss "D"
connector to the ECM only. not tothe main wire harness {see page11-37).
Turn the ignition switch ON.
Measure voltage between D13(+) terminal and D22 (-l ter-mlnal.
Repair opoa or shon inREO/WHT wiro botwoen ECMlDl3l and th6 ECT sonsor.R6pair shon in REO/WHT YYi..b6tw66n ECM {D131and TCM.
ls the.e approx. 5 V?
Substiluto a known-good ECMand rochock. ll lymptom/indica-tion goea 6wsy, replaco tho o.igi-n6l ECM,
A/T only
I
_i
11-59

(From1 1-60){From
A/T only
Turn the ignition switch OFF.
Connect the test harness betweenthe ECM and connectors (seepage 11-37l-.
Turn the ignilion switch ON.
Measure voltage between D1 1 {+ )terminal and 022 (- I terminal.
Turn the ignition switch OFF.
ls voltage approx. O.5 V at lullclose throtlle. and approx. 4 vat full open throttle?NOTE: There should be asmooth transition as the throt-tle is depressed.
Disconnect the 22P connectorfrom the Transmission ControlModule (TCM).
lurn the ignition switch ON.
Substitute a known-good ECMand roch6ck. ll symptom/indica-tion 9063 away, roplaco th6 origi-nal ECM.- Replaco tho TPaonsoa,- Repai. opon or ahonin RED/BLK wir. b€-twoon ECM lDl1l,TCM 6nd TP sonsor.
ls voltage approx. 0.5 V ar fullclose throttle, and approx. 4 Vat tull open throttle?NOTE: There should be asmooth transition as the throt'tle is deprossod.
page 1 1-60)
Repsir op.n in GRN/8LU wii6 botwoon ECMlD22l snd tho TPaenaot.
ls there approx. 5 V ?
Turn the ignition switch OFF.
Connect the test hamess betweenthe ECM and connector {see page11-37).
Turn the ignition switch ON.
Measure voltage between D2O{+) terminsl and D22 {-}termtnal,
Ropoi. open in YEL/BLUwire bgtween ECM{D20} and rho TP30naot.
ls there approx. 5 V 7
-ReDai. ahort in YEL/BLU wiroborwoon ECM (D2Ol and tho TPson30t.-Sub3tituto a known-good ECM6nd rochock. It prcacribod vol-t6go is now availablo, roplacoth6 original ECM.
Fr. o.5 v n tua .b drdn ?
11-61

{From pag6 l1-62}
Turn the ignition switch ON.
Messuro voltage b€tw€6n RED/YEL (+) terminal and bodyground.
M€asurs voltage between RED/YEL {+) rerminal and GRN/BLU{ - I terminal,ls thore approx. 5 V ?
Rsp.lr op.n in GBt{/8LU wir bctwo.r ECM
lD22l snd tho IATaanaor.
Turn the ignition switch OFF.ls thero a99rox. 5 V ?
Sub.lhul. a tnown{ood ECMlnd rachack. It rymptom/lndlc!-don gort arv.y, t pl.c. dr! oilgl-n.l ECM.
Rap.lr opon or rhon In REDfYELwh. b.tw..n ECM lDl5l rnd th.lAf tcrrao.-ls th€re spprox. 5 V ?
Connsct lhg t€st hamess "D"
connoctor to the ECM only. not toth6 main wire harness lsse page
11-371.
Turn tho ignition switch ON.
Mgasur€ voltag€ bstwgon D15(+) terminal and D22 l-ltgrminal.
S0brlitrrt. . lnown{ood ECM'|d '. 1 1-63

PGM-FI System
Knock Sensor (KS) tB18C1 enginel
ml- nl: The Malfunction Indicator Lamp (MlL) indicates Diagnostic Troubte Code (DTC) 23: A probtem inthe Knock Sensor (KS) circuit.
a6l--fzt.i--1/.---r+\
ware sido
o ooooo ooo ooo o looooooooo oooo ooo oo ooo I oooo oooo
11-74
- The MIL h6s boon r6port6don.- With th6 SCS ahort connec-tor connoctod (soe pago11-341, codo 23 is in-dicrtod.
Oo the ECM Reset Proceduro (seepage 11-35).
Start the engine. Hold the engineg!-3,Opq rpm with no load {A/T in
Lryl orlPlposirion, M/T in neurra until the radiator fan comes on,then let it idle.
Hold the engine at 3,0O0-4,000rpm for 10 seconds.Intomittor failure, ay5-t.m is OK at this tim6(teat drivo mav bonec€saary,.Chock tor Door connec-tion3 or loo3o wlaos etC222 {locatod 6r ghrshock tow6r), Cl33(KSl and ECM.Turn the ignition swirch OFF.
Connect the test harness to themain wire harness only, not to theECM (see page 1 1-37).
Check for continuity between D3terminal and body ground.
Ropdr short in RED/BLUwiro b€tweon ECM {D3land ths Ks.
(To page 11-75)

PGM-FI System
A/T Fl Signal A/B (A/T only)
\[l0l- The Maltunction Indicaror Lamp (MlL) indicates Diagnostic Trouble Code (DTC) 30: A problem In-L= the A/T Fl Signat A circuit between Transmission Control Module (TCMI and ECM.
tItil- The Malfuncrion Indicaror Lamp {MlL) indicates Diagnostic Trouble Code {DTCI 31: A problem In-Li!- the A/T Fl Signal B circuit between Transmission Controt Module (TCM) and ECM.
\.__r_/ \.__r_/-l 30 l- o'-l 3t l------ /----\
84'
+ulty? Continuity?
r: code 31 1A/T Fl signal Bl
11-76
Wlth tho SCS ahon connocrolconi|ocd {!o. p.g. 'l 1 -341, codo3O and/or 31 ars indicltod.
Oo ths ECM Resot Proceduro {seepag€ 'l 1-35).
Test drive necessary.Drive the car lor several miles sothat the transmission uDshifts anddownshilts several times.
Intormittant tsilu.o, sy3tem iB OKat thir tima,Chack lor poor connactions otl.ro!€ wiror at C419 (TCM] andECM.
Does the MIL indicare code30 and/or 31?
Turn the ignition switch OFF.
Connect the test harness to th€main harness only, not to the ECM(see p8go l'l-37).
Disconnect the 22P connectorfrom the TCM.
Check lor continuity between B3andlor 84' terminal and bodygrouno.
Ropair lhon in GRN/8LU or GRY'wiro b6twoon ECM (83 or 84'land tho TCM.
(To page 11-77)

ldle Gontrol System
Air Conditioning Signal
This signals the ECM when there is a demand for cooling from the air conditioning system.
Connect the t€st harness betweenthe ECM and connectors. Discon-nect "B" connector from the mainwire harness onlv, not the ECM{see page 11-37}.
Turn the ignition switch ON.
Measure voltage between 851+ )lerminal and A26 l- I terrninal.
Sub.litut ! known{ood €CMrnd r6 ls there approx. 5 V?
Turn th€ ignition switch OFF.
Reconnect "8" connector to themain wire harness.
Turn the ignilion switch ON.
Momentarilv connect A15 termi-nalto A26 terminsl severaltimes.
Momsntarilv connect the 8LK/RED t€rminal of the 4P connectoron the A/C clutch rel6v to bodyground sevsral times.
ls there a clicking noise fromthe A/C comDressor clutch?
3o6 rlr condhlohar in-rDactlon llaa lac{ion221.
ls there a clicking nois€ lromth€ A/C comoressor clutch?
Rop.ir opon in BLK/BED wiro be-two.n ECM {A15} and A/C clurchrally.
ooooooooooooo
oooooooooooo
oooooooo
oooooooo
ooooooooooo
ooooooooooo
.pprox. 5 V?
426 (- )
Cllcklng?
lTo page
11-84
-

ldle Control System
Alternator (ALTI FR Signal
This signals the ECM when the Alternator (ALT) as charging.
D9 l+)
Inspection ot ALT FR Sign.l.
Connect the tost harness betweenthe ECM and connectors. Discon-nect "D" connector from themain wire harnoss only, not theECM lsee page 11-37).
Turn the ignition switch ON.
Measure voltage between D9 (+ )terminal and A26 {-}terminal.
Sub{inno s known-good ECMand redrack. It pro.ctibod volt gola now availablg, ropllco tha orlg-inal ECM.
ls there approx. 5 V?
Turn the ignition switch OFF.
Reconnect "D" connector to themain wire harness,
Start tho engino. Hold the engine
!L3,099 rpm with no load (A/T in
LN] or El position, M/T in neutral)until the radiator tan comes on,rhen let it idle.
Measuro voltage between Dg (fl
terminal and 426 (- I terminal.
Does the voltage decreasewhen headlights and .eardelogger are turned on?Turn ths ignition switch OFF.
ALT FR rignal is OK.
o oo oo o ooooo
ooooooooooo
Voh.go?
ooooooooooo
ooooooooooo
1 1-86
(To page 1 1-87)
=-