1994 HONDA INTEGRA Crank pulley

1.Remove the cylinder head cover.
. Refer to page 6-31 when installing.
Remove the Dulley bolt and crankshaft pulley (see
page 6-8).
Remove the middle cover and the lower cover.
NOTE:
. Do not use the middle cover and lower cover for
storing items disassembled.
. Clean the middle cover and lower cover before
installation.
CAP NUT 6 x 1.0 mm
10. Loosen the adjusting bolt 180'.
1'1. Push the tensioner to remove tension from the tim-
ing belt, then retighten the bolt.
12. Remove the timing belt from the pulleys.
NOTE: Push the tensioner pulley toloosen the belt.
8.
9.8 N.m 11.07.2 rbl.ftl
WASHER
orReplace when damaged
CYLINDEF HEADCOVERReter to page 6-31 wheninstalling.ADJUSTING BOLT10 x 1.25 mm54 N.m 15.5 kg{.m,/r0 lbf.ftlFor adjustment only,
TIMING BELTAdiustment, Page 6I
LOWEB @VER
MIDOLE COVER
6x1.0mm9.8 N.m 11.0 kgJ m, 7.2 lblftl
6x1.0mm9.8 N.m ('1.0 kgt.m,7.2 lbl fr)
Remove anY oiland clean
KE
6x1.0mm
NMING BELTGUIOE PLATElnstallwith concavesurface facing out.
and clean.CRANKSHAFT PULLEYRemove any oiland clean on ihetiming belt guideplate sido.9.8 N.m (1.0 kgtm,7.2lbt'ftl
6-11

Timing Belt
Installation
Install the timing belt in the revorce order of removal;
Only key points are described here,
NOTE: Cl€an the middle cover and lower cover beforeinstallation.
L Position the crankshaft and th€ camshaft pulleys asshown before installing the timing belt.
A. Set the crankshaft so that the No. 1 oiston is at
top dead center (TDC). Align the g.oovo on the
t€eth side of the timing belt d.ive pulley to the Opointer on the oil pump.
L Align the TDC marks on intake and exhaust pul-
tevs,
NOTE: To set the camshafts at TDC position for
No. 1 piston, align the holes in the camshafts
with the holes in No. l camshaft holders andinsert 5,0 mm pin punches in the holes.
PIN PUNCHES, 5.0 mm
2. lnstall the timing belt tightly in the sequence
snown.
O timing belt drive pulley {crankshaft) + @Adjusting pulley * @ Water pump pulley - @Exhaust camshaft pulley + @ Intake camshaft pul-
lev.
TDC mark align6d with thepointer on back cover,TDC MARK
6-12

Gylinder Head
Removal
I
t
Engine removal is not required for this procedure.
CAUTION: To avoid damaging tho cylinder head, wait
until tho ongino coolant temporature drops bolow 100"F
{38"C) beforo loo36ning the rotainin0 bolts.
NOTE:
. Inspect the timing belt before removing the cylinder
neao.
. Turn the crankshaft pulley so that the No. 1 piston is
at top dead center (TDCI (page 6-12).
. Mark all emissions hoses before disconnecting them.. Anti-theft radios have a coded theft protection circuit.
Be sure to get the customer's code number before.- Disconnecting the battery.- Removing the No. 32 (7.5 A) fuse irom the under-
hood fuse/relay box.- Removing the radio.
After service, reconnect oower to the radio and turn it
on.
When the word "CODE" is displayed, enter the cus-
tomer's 5-digit code to restore radio operation.
1. Disconnect the negative terminalfrom the battery.
2. Drain the engine coolant (see page 10-5).
. Remove the radiator cap to speed draining.
3. Relieve fuel pressure (see Section 1 1).
@ Do not smoke whils working on tusl
systom, keep opon flame or spark away trom work
area. Drain fuol only inlo an approvod containsr.
4. Disconnect the fuel feed hose.
SERVIC€ BOLT
WASHERSReplace.
5, Remove the intake air duct.
Remove the breather
evaporative emission
hose, water bypass hose and(EVAP) control canister hose.

Cylinder Head/Valve Train
818C1 engine
Special Tools ............. 6-34
wEc
Troubleshooting Flowchart
WEC Solenoid Valve ................... 6-36
VTEC Pressure Switch ................. 6-38
VTEC Solenoid Valve Inspection .... 6-41
Rocker Arms
Manual Inspection .....,................. 6-42
Inspection Using Special
Tools ....................................,.....,.. 6-/|i|
Valve Glearance
Adiustment ............ 6-44
Timing Belt
lllustrated 1ndex ............................... 6-46
Inspection .............. 6-48
Tension Adiustment ........................ 6-48
Removal ................. 6-4{l
lnstallation ............. 6-51
Crankshaft Pulley Bolt
Replacement .........6-47
Cylinder Head
lllustrated Index ............................... 6-53
Removal .................6-55
Warpage ................6-74
lnstallation ............. 6-75
Rocker Arms
Removal ................. 6-60
Location ................. 6-61
lnspection .............. 6-62
Arm-to-Shaft G|earance .................. 6-63
Installation ............. 5-64
Camshafts
Inspection .............. 6-65
Valve Guides
Valve Movement .............................. 6-70
Replacement .........6-71
Reaming ................. 6-72
Valve Seals
Reconditioning ......6-73
Valves. Valve Springs and Valve Seals
Removal ................. 6-67
lnstallation Sequence ..........,.......,... 6-69
Valve lnstallation ............................. 6-70

Valve Clearance
Adiustment
NOTE:
. Valves should be adjusted cold; at a cylinder head
temperature of less than 100"F (38'C).
. Adjustmsnt is the same for intake and exhaust
vatves.
o After adjusting, retorque the crankshaft pulloy bolt to
177 N.m ( 18.0 kgf.m, 130 lbf.ft).
1. Remove cylinder head cove..
ADJUSTING BOLT LOCANONS:
IMTAKE
No. 4 No.3 No. 2 No. 1
No.4 No.3 No.2 No. 1
EXHAUST
Set No. 1 piston at TDC. "UP" mark on the pulley
should be at top, and TDC grooves on the pulley
should align with the pointer on back cover. TDC
grooves (white paint) on the crankshatt pulley
should align with pointer on the timing belt lower
cover.
Numbr. 1 pirton .t TDC:
6-44
FOI{IER Ot{LOWEF COVERTDC MANKlP.int d whit.t
3.
4.
Diroction ofaotation.
Adjust valv6 clearanc6 on No. 1 cylinder.
Intlkc: 0.15 - 0.19 mm (0.006 - 0.0,07 inl
Exh.u3t 0.17 - 0.21 mm (0.007 - 0.m8 inl
Looson lh6 locknut and turn the adjusting screw
until feeler gaugo slides back and fonh with a slight
amount of drag.
TAPPET AI\,USTEN WREI{CI{O'LAA - PRIOIq'
7 x 0.75 mrn20 f+|n (2.0 kgf'm. 14lbtftl
FEEEN GAUGE

Tightsn the locknut and recheck clearance again.
Rep6at sdjustm6nt if necossary.
Rotsts tha crankshaft 180' counterclockwiss
(c8mshaft pulley turns 90'). The "UP" mark should
be on th€ sxhaust 8id6, Adiust vslves on No. 3 cylin-
oer,
Nurrb.r3tittondTDC:
FEEI.IR GAUGE
.UP' MANKS
7. Rotato crankshaft 180' countsrclockwise to bring
No.4 piston to TDC. The "UP" mark should bo
pointing straight down. Adjust valves on No. 4
cylinder.
Numb.r 4 pidon .t Tt C:
8, Rotate crankshaft 180" counterclockwis€ to bring
No. 2 piston to TDC. The "UP" marks should be on
the intaks sid6. Adjust valves on No. 2 cylinder.
Nonb.r 2 pirton .l TltC:
NOTE: Refer to page 6-78 when installing cylinder head
cover.
6-45

Timing Belt
. ReJerto page 6-51 for positioning crankshaft and pulley before installing belt.. Mark the direction of rotation on the belt before removing.
. Replace the rubber seals for oil leakage between the cylinder head and cover.. Do not use the middle cover and lower cover for storing items disassembled.
. Clean the middle cover and lower cover before installation.
lllustrated lndex
NOTE:
WASHERReplace whenCAP NUTx 1,0 mm9.8 N.m 11.0 kgf.m,7,2lbttrlor deteriorated.
CYLINDERHEAO COVERReter to page 6'78when installing.
RUBBER SEALSReplace when damagedor deteriorated,
TIMING BELTInsp€ctaon, page 6-48Adjustment. page 6-48R€placement. page 6'49
MIDDLE COVER
5xl,0mm9.8 N.m (1.0 kgt m,7.2 rbtftt
8 x 1.25 mm56 N.m 15.7 kgt m,41 tbtftl6x1.0mm9.8 N.m (1.0 kgt.m,7.2lbf ftl6x1.0mm9.8 N.m {1.0 kgl.m,7.2lbf.ftl
Installwith concavesurface lacing in.Clean.
TIMING SELDRIVE PULLEYRemove any oil and clean.
10 x 1.25 mm5a N.m 15.5 kgl.m.(} tbf.ftlFor adiustment onlydo not remove.
BOLTInstallwith concavesurface tacing out.Remove any oiland clesn.1il x 1.25 mm177 N.m 118,0 kgtm, 130lbtft)Replacement, page 6-47
COVER
PULLEYRemove any oil and cleanon the timing belt guideplate side.NOTE: When installing a new crankshaft and/or new bolt:
O tighten the crankshaft pulley bolr to 196 N.m (20.0 kgf.m. 145 lbf.ft),
@ loosen bolt,
@ retighten it to 177 N.m fl8.0 kgf.m, 130 lbnft).
3-E
6-46

Grankshaft Pulley Bolt
Replacement
NOTE:
. Crankshaft pull€y bolt size and torqus value:
1,0 x 1.25 mm
177 N.m (18.0 kgt.m, 130 lbf'ft)
. When instslling a new crankshaft 8nd/or now pulley
bolt:
O tight6n the pulley bolt to 196 N'm (20.0 kgf'm, 145
tbf.ft).
@ looson the bolt,
@ r6tighten it to 177 N.m (18.0 kgf'm, 130 lbf'ft).
. When reinstalling the bolt, lubricate the thresds 8nd
flange with engine oil, but don't lubricate the washer
and pulley.
Lubriceto with engine oil hers.
SOCKET WRENCH, 19 mmCOi'MEBCI,ALLY AVAILABT.E
PULITY HOLDEB ATTACHMEUT,HEX slt mm, OFFSETOTMAB - PY3O1OA
6-47