1993 MITSUBISHI ECLIPSE lock

-
23-34BODY - HoodSERVICE POINTS
OF INSTALLATION
19.APPLICATION Or GREASE TO HOOD HINGE/l4HOOD LATCH/l 1. HOOD LOCK RELEASE HANDLE
’Apply multipurpose grease to all moving parts.
Grease: MOPAR Multipurpose Grease Part
No2932524 or equivalent
18AO3926. INSTALLATION OF BUMPER
Install the bumper so that the amount of projection from thefront end
@per bar is as shown in the illustration.

BODY - Liftgate23-35
FTGATEN230AAT
EMOVAL AND INSTALLATION
11-16 Nm
8- 12 ft.lbs.\9-14 Nm
7- 10 ftlbs.
1. Bumper
2. Llftgate damper (upper)
3. Liftgate outer weatherstrip
4. Liftgate damper (lower)
5. Liftgate opening weatherstrip
Liftgate hinge removal stepsHeadlining (Refer to
P.23-89.)6. Connection for rear washer tube
Center pillar trim (drtver’s side)
Quarter trim (driver’s side)
1(Refer toP.23-85.)7. Connection for liftgate wiring harness
8. Liftgate
9. Liftgate hinge
Liftgate removal steps6. Connection for rear washer tube
Center pillar trim (driver’s side)(Refer to
Quarter trim (driver’s side)
1P.23-85.)7. Connection for
liftgate wiring harness
8. Liftgate
Liftgate lock release cable removal stepsRear seat (Refer to
P.23-93.)Scuff plate (driver’s side)
Quarter trim (driver’s side)
(Refer to
Rear end trim
’ P.23-85.)Rear side trim
l
10. Liftgate latch5-8 ftlbs.
4/
1118AO973
Liftgate lock release handle removal stepsScuff plate (driver’s side)
(Refer to
P.23-85.)13 Release handle cover
l * 14.
Liftgate lock release handle
Liftgate latch removal stepsRear end trim (Refer to
P.23-85.)l *
10. Liftgate latch
Liftgate lock cylinder removal stepsRear end trim (Refer to P-23-85.)
1 1 Retainer
4*12.
Liftgate lock cylinder
Liftgate striker removal steps
Liftgate trim (Refer to P.23-86.)16
Liftgate striker
Liftgate stopper removal stepsRear side trim (Refer
td P.23-85.)
17. Liftgate stopper

._-_,. -/a,_ . . ._ :-. nkFiller Door
FUEL TANK FILLER DOOR
REMOVAL AND INSTALLATIONSERVICE POINTS OF REMOVAL17. REMOVAL OF
LIFTGATE STOPPER
Caution1. Never try to disassemble the
liigate gas spring crbum it.
2. Always bore a hole in the gas spring to
release the
interior gas before the spring is discarded.
SERVICE POINTS OF INSTALLATION14,APPLICATION OF GREASE TO
LIFTGATE LOCK RF-LEASE HANDLE/
10. LIFTGATE LATCH
Apply multipurpose grease to all moving parts
Grease: MOPAR Multipurpose Grease Part NO.
2932524 or equivalent
N23JAAa
Pre-removal Operation0 Removal of Rear Seat
Post-installation Operationl Installation of Rear Side Trim
Quarter Trim and Scuff Plate
(Refer to P.2385.)
0 Installation of Rear Seat
(Refer to P.23-93.)0 Fuel Filler Door Adjustment
(Refer to P.23-30.)Removal steps+a
1. Fuel filler door2. Fuel filler door hookWA0462
3. Release hatidle coverNOTEl * 4. Fuel filler door lock release handle(1) Reverse the removal procedures to reinstall.5. Fuel filler door lock release cable(2) +a : Refer to “Service Points of Installation”.
SERVICE POINTS OF INSTALLATION4.
APPLICATION OF GREASE TO FUEL FILLER,DOOR LOCK j
:(“‘: ,: : ,.-;gz/ :,; Apply multipurpose gre
:’ j:: -:l : :. ,;&r: &;iGrease: MOPARMu
; _

*,i
bSE PANEL
BODY - Loose Panel23-51
N23sAAK/&OVAL AND INSTALLATION
.-9-14
Nm.7-10 ft.k
Front pillar ILH) /Headlight support
Inter cooler duct
Front/fascia bracket
/crossmember
Deck crossmember sta
lSA0463
18AO971Headlight support
Talon>4-6
Nm3-4 ft.lbs.Hood lock support
WA0970
ISA0472
LT IVIUUIn
Laser>I
18AO939