1993 GMC SIERRA radio

TUNE
To tune in radio stations, push the (t) to increase frequency and (-) to
decrease frequency.
A MIFM
Push to get AM or FM.
SEEK
Press the SEEK button to make the receiver seek, and stop at, the next
higher available station.
SCAN
Press the SCAN button to make the receiver scan, and momentarily pause
at, all available stations.
SCAN will appear in the VF display while the
receiver is in the scan mode. Press
SCAN again to cancel the scan mode
and hold the current station.
Pushbuttons
The six pushbuttons let you return to favorite stations. You can set the
pushbuttons for up to twelve favorite stations
(6 AM and 6 FM). To set the
pushbuttons, just:
Tune in the station you want.
Press the SET button. (SET appears in the VF display for a few
seconds.)
Within 5 seconds, push one of the six pushbuttons to store the station.
After that, whenever you press that button, the preset station will return.
Clock
To set the clock, just:
Press the SET button. The word SET will light up in the VF display.
Within 5 seconds, press and hold the SEEK button until the correct hour
Then, press and hold the SCAN button until the correct minute appears
appears on the display.
on the display.
After you set the time, the word SET will remain
in the VF display for a
few seconds.
Tone
To adjust the tone of this radio combination, see the instructions for the
graphic equalizer tape deck.
3-1 5
ProCarManuals.com

Comfort Controls & Audio Systems
AmSt
The AmSt button is just below the PWR button. Push this when you tune to
an AM station that broadcasts in stereo. Your
STEREO light will come on
when you’re receiving AM stereo.
If you push AmSt and there is no more
noise,
it means the station is weak. You’ll hear the station better if you don’t
use
AmSt. Just push the AmSt button again to cancel stereo.
NOTE: Your Delco system may be able to receive C-QUAM@ stereo
broadcasts. Many AM stations around the country use C-QUAM@ to produce
stereo, though some do not. C-QUAM@ is a registered trademark
of Motorola
Inc. If your Delco system can get C-QUAM@ signals, your
STEREO light will
come on when you are receiving stereo.
Cassette Deck with Graphic Equalizer
K2311
Press the PWR button on the radio to turn the unit on. The radio will play
until a cassette is pushed into the cassette entry door (the \
tape side goes in
first.) The cassette deck is built to work best with tapes that are
30 to 45
minutes long on each side. Tapes longer than that are so thin that they may
not work well in this player.
Once the tape is playing, use the
VOL, BAL and FADE controls on the
radio. The arrows indicate which side
of the tape is being played.
Equalizer
Boost the bass, emphasize a voice in a song, brighten the treble-your
equalizer enables you to adjust five separate sound frequencies \
to your
individual taste.
3-1 6
ProCarManuals.com

Press (+) to emphasize a frequency, press (-) to de-emphasize it. It’s best
to begin with all the controls in the middle position, then adjust each control
as you like. Observe the
VF display for relative emphasis.
Cr02
This button sets tape bias. When playing high bias chrome or metal tapes,
press
Cr02 (the light in the button will come on). When playing standard
tapes, press the button again (the light will go out).
PROG
To go from one side of the tape to the other, press the PROG button.
Observe the lighted arrows to determine which side of the tape is being
played.
If a tape is inserted with side “1” (or ‘X,) up, men the up arrow means that
that side is being played. Likewise, a down arrow would indicate that side
“2”
(or “B”) had been selected. The player will automatically switch to the other
side of the tape when the first side ends.
EJECT
Press EJECT to eject the cassette tape from the player (the radio will t\
hen
FWD
To rapidly advance the tape, press FWD. The light in the button will be lit
and the tape will rapidly advance until you press the
REV button lightly.
play.)
SEEK
To
search for the next selection on the tape, forward or back, press SEEK
(the light in the SEEK button will be lit) and either FWD or REV. For the
seek mode to stop, there must be at least a 4-second gap between
selections on the tape.
REV
To rapidly reverse the tape, press REV. The light in the button will be lit and
the tape will rapidly reverse until you press the
FWD button lightly.
REPT
Press REPT to repeat the currently playing selection on the tape. For the
repeat to stop, there must be at least
a 4-second gap between selections.
3-1 7
ProCarManuals.com

Pmbkms on the Road
not be able to get enough power from a single battery in another vehicle
to start your diesel engine.
If your vehicle has more than one battery, use the battery that’\
s closest
to the starter-this will reduce electrical resistance.
2. Get the vehicles close enough so the jumper cables can reach, but be
sure the vehicles aren’t touching each other.
If they are, it could cause a
ground connection you don’t want. You wouldn’t be able
to start your
vehicle, and the bad grounding could damage the electrical syst\
ems.
You could be injured
if the vehicles roll. Set the parking brake firmly
manual transmission in
N (Neutral).
If you have a four-wheel-drive vehicle, be sure the transfer c\
ase is
not in
N (Neutral).
1 on each vehicle. Put an automatic transmission in P (Park) or a
3. Turn off the ignition on both vehicles. Turn off all lights that aren’t need-
ed, and radios. This will avoid sparks and help save both bat\
teries. And
it could save your radio!
ou leave your radio on, it could be badly damaged. The repairs
r.,Jldn’t be covered by your warranty. I
4. Open the hoods and locate the batteries.
Find the positive
(t) and negative (-) terminals on each battery.
5-4
ProCarManuals.com

Fuse Block
K2644
The fuse block is in the instrument panel on the driver’s side.
You can remove fuses with a fuse extractor,
if you have one. To remove
fuses
if you don’t have one, hold the end of the fuse between your thumb
and index finger and pull straight out.
Be sure
to use the correct fuse. If you ever have a problem on the road and
don’t have a spare fuse, you can “borrow’’ one of the correct value. Just pick
some feature
of your vehicle that you can get along without-like the radio or
cigarette lighter-and use its fuse,
if it is of the value you need. Replace it
as soon as you can. See “Fuses and Circuit Breakers” in the Index for more
information.
Exhaust System
To help prevent damage to your exhaust system, do not continue to drive
your vehicle
if you notice:
Engine misfiring
Loss of performance
Other unusual operating conditions
Have your engine and exhaust system serviced regularly.
Three- Way Cataiytic Converter
Your vehicle’s three-way catalytic converter is designed to reduce the
pollutants in your vehicle’s exhaust. Use only unleaded fuel in your vehicle.
If
6-65
ProCarManuals.com

Service & Appearance Care
Fuses and Circuit Breakers
Name
Gages
Turn-B/U EMCllgn
Inj. A
Brake
AC/Htr
Ctsy
Park LP P. Lps
StoplHaz. Wiper
Radio
Accll g n
.
Acc/Batt. Crank 4WD
DRL
Circuits Protected
Cruise Control, 4 WD Display Illum. Rear
Window Defogger Timer, Aux. Batt. Relay
Feed, Safety Belt Buzzer Timer, Cluster
Ign. Feed
Back-up Lamps, Turn Signals
T.C.C., Air Diverter, E.S.C., E.G.R., E.C.M.
Ign., R.W.A.L. Brake Switch
Throttle Body Injectors R.W.A.L., Cluster-Speed0
H.V.A.C.
4 WD, Aux. Batt. Relay
Dome Lamp, Cargo Lamp, Ctsy. and Glove
Box Lps. (TR-9), Radio (Memory-Clock)
Horn Relay, Horn Feed, Cigar Lighter, Park
Lamps
C49 SW Illum., Headlamp “On” Warning,
Radio Illum., H.V.A.C. Illum.
Haz. Flasher, Seat Belt Buzzer, Stop
Lmps., R.W.A.L. Memory
Windshield Wiper, Washer
Radio Feed
Pwr. Windows
Door Locks, Rear Window Defogger
Crank, Discreet Four Wheel Drive
Daytime Running Lights
Fuse
20 Amp
15 Amp
10 Amp
10 Amp
15 Amp
25 Amp
20 Amp
20 Amp
5 Amp
15 Amp
25 Amp
10 Amp
5 Amp
25 Amp
15 AmD
Circuit
Breaker
30 Amp
30 Amp
An inline fuse
is used for the underhood lamp
10 not use fuses of higher amperage than those recommended above.
TO038
6-1 00
ProCarManuals.com