Page 99 of 398

Downloaded from www.Manualslib.com manuals search engine To set the parking brake:
Hold the regular brake pedal down with your right foot. Push down the
parking brake pedal with your left foot. If the ignition
is on, the brake
system warnin? light
will come on.
I-
I
When you move out
of “P” (Park) or “N”
(Neutral), if your
engine
is running,
your parking brake should go off.
If it
doesn’t, you have a
parking brake
problem and should have it fixed.
In the
meantime,
you can
still release your
parking brake. Just
pull on the manual
release lever, as
shown.
I
3me-q 5::- &*ZL !My& se-4
A CAUTION: . -- .
If your hand or arm is in the way of thi’pedal, you could be -,::+ -+..:
hurt. The pedal springs back quickly. Keep your hand and arm !+. ,--,:“:
away when you use 1 ! manual release lever. :,F
.L- ..
-.7 7 .--.. , - ., .I .. - .>, _. .- : - .?f I - - .. - --. . ’-: .:. ..:= . ’. + .? .. .
NOTICE
Driving with the parking lake on can cause ~UL- rear bra,
overheat.
You mav have to replace them- and vou could also
,.*age ~ ~. .: . ~ i nther pal vnur vfihicle.
L .~-:’? . - I . - . i i .. ~
85
Page 109 of 398
Downloaded from www.Manualslib.com manuals search engine THE TURN SIGNALIMULTIFUNCTION
LEPER
The lever on the left side of the steering column includes your:
Turn Signal and Lane Change Indicator
Headlight High-Low Beam
Flash-To-Pass Feature
Headlamp Washers (Export Only)
Windshield Wipers
Windshield Washer
Cruise Control
Page 111 of 398
Downloaded from www.Manualslib.com manuals search engine As you signal a turn or a lane change, if the arrows don’t flash but just
stay on, a signal bulb may be burned out and other drivers won’t see your
turn signal.
If a bulb is burned out, replace it to help avoid an accident. If the green
arrows
don’t go on at ail when you signal a turn, check the fuse (see
“Fuses” in the Index) and for burned-out bulbs.
Headlight High-Low Beam
To change the
headlights from low
beam to high or high to
low, pull the turn signal
lever all the way toward
you. Then release it.
When the high beams
are on, a blue light on
the instrument panel
also will be
on.
Flash-To-Pass Feature
This lets you use your high beam headlights to signal a driver in front of
you that you want to pass. It works even if your headlights are off.
97
Page 112 of 398

Downloaded from www.Manualslib.com manuals search engine To use it, pull the multifunction lever toward you. When you do:
If your headlights are off Your high beam headlights will turn on. They’ll
stay
on as long as you hold the lever there. Release the lever to turn them
off.
If your headlights are on. but on low beam: The system works normally.
Just pull the lever. Your headlights
will shift to high beam and stay there.
To return to low beam, just pull the lever toward you.
If your headlights are on. and on high beam: Your headlights will switch
to low beam.
To get back to high beam, pull the lever toward you.
Windshield Wipers
WIPER To control the wipers, turn the band on the multifunction lever.
MIST: Turn the band away from you and then release it for a single wipe
cycle. For more cycles, hold the band
on MIST longer.
LO or HI: Turn the band toward you to either LO (low speed) or to HI
(high speed), depending on the wiper speed you want.
DELAY: With this you can set the wiper speed for a long or short delay
between wipes. Move the band to ON for long delays and the closer you
get to LO the shorter the delay.
OFF: To turn the wipers off, turn the band to OFF.
98
Page 114 of 398
Downloaded from www.Manualslib.com manuals search engine la CAUTION
splash-am block your vision. Yon could hit another vehicle or
go off the road. Check your washer fluid level often.
* Xn freezing weather, don't use your washer until the
windshield is warmed. Otherwise the washer fluid can fam
I Headlight Washer (Export Only)
If you have this feature, you will wash your headlights while washing your
windshield at the same time
in bad weather. Just press the PUSH paddle
on the multifunction lever.
100
U
c
0
fi
I
I
Page 116 of 398
Downloaded from www.Manualslib.com manuals search engine If you leave your Cruise Control switch on when you’re not
using Cruise,
you might hit a button and go into Cruise when
you don’t want to. You could be startled and even lose control.
Keep the Cruise Control switch
“OFF” until you want to use it.
I
2. Get up to the speed you want.
W PUSH
.+9
I
4. The digital
1 instrument panel
cluster has
a
“CRUISE
ENGAGED” light
that will come
on.
There is no light on
the analog cluster.
5. Take your foot off the accelerator pedal.
102
Page 119 of 398
Downloaded from www.Manualslib.com manuals search engine To Get Out of Cruise Control
There are two ways to turn off the Cruise Control:
1. Step lightly on the brake pedal ; OR
I - P
2. Move the CRUISE switch to “OFF” (The “CRUISE” light will go
out .)
105
Page 120 of 398
Downloaded from www.Manualslib.com manuals search engine To Erase Speed Memory
When you turn off the Cruise Control or the ignition, your Cruise
Control set speed memory is erased.
LIGHTS
You’ll find the control on the left side of the instrument panel.
It controls these light systems:
Headlights
0 Taillights
0 Parking Lights
0 Underhood Light (Option)
0 Instrument Panel Lights
0 License Plate Lights
0 Interior Courtesy Lights
Fog Lights (Option)
0 Rear Fog Lights (Export Only)
ALL LIGHTS PANEL LIGHTS
EXCEPT
BRIGHTNESS
light system. HEADLIGHTS
manually work your
Here’s
how
to
I )- COURTESY
OFF ALL LIGHTS LIGHTS
Lights On Reminder
If you open the door while leaving the lights on, you will hear a warning
tone.
106