1993 CADILLAC DEVILLE lock

Downloaded from www.Manualslib.com manuals search engine - Attach the wheel
wrench to the jack bolt
and rotate it clockwise
(to the right). That
will
raise the lift head a
little.
If your vehicle
has a wire wheel cover or an aluminum wheel, read the
part that describes your wheel.
Aluminum Wheels
Use the flat end of the
wheel wrench. Insert
into the small slot on
the wheel and gently
remove the center
cover. Be careful not
to drop the cover
on
the ground, you could
scratch it.
Now
see “Jacking and Removing Flat Tire.”

Downloaded from www.Manualslib.com manuals search engine .. . 1
- Use the omer end of
the wire wheel wrench
like this. Remove the
special anti-theft wheel
nut
by turning it
counterclockwise. -
,I_
~ ~ ~~
__
Remove the wheel disc.
Jacking and Removing Flat Tire
Using the whee-l wrench, loosen all the wheel nuts. Don’t remove them,
yet.
Your Cadillac has a
notch on the frame
near each
of the
wheels.
Fit the lift
head into the notch
nearest the wheel with
the flat tire. e 1
The jack handle has markings at 8” for the rear and lo” for the front to
- use which will help you to locate the jacking notches in the frame.

Downloaded from www.Manualslib.com manuals search engine 7 -
A CAUTION:
- !tting under a vehicle when it is jacked up is dangerous. If the
vehicle slips
off the jack, you could be badly injured or killed.
Never get under a vehicle when it is supported only by a jack.
*
-
Remove all the wheel nuts and take off the flat tire.
Now raise the vehicle.
Just keep rotating the
wheel wrench,
on the
jack, to the right
(clockwise). Raise the
vehicle far enough
off ---.
the ground so there is
enough room for the
flat tire to come
off -
and the compact spare
to fit. .- . -
r
-. .
a-
L ..
252

Downloaded from www.Manualslib.com manuals search engine I”
7 :- _.
I ’.
.. -
Replace the wheel nuts ._
with the rounded end
of the nuts toward the
wheel.
Tighten each
nut
by hand until the
wheel is held against
the hub.
Lower the vehicle
completely by rotating
the wheel wrench
counterclockwise.
254
c

Downloaded from www.Manualslib.com manuals search engine Or you can use the
release lever located
on the left side in the
trunk. Pull the lever
toward the rear
of your
vehicle to release the
fuel door.
To take off the cap, turn it slowly to the left (counterclockwise).
While refueling, hang the cap inside the fuel door.
A CAUTION:
If you get gasoline on you and then something ignites it, you
could be badly burned. Gasoline can spray out on you if you
open the fuel filler cap too quickly. This spray can happen if
your tank is nearly full, and is more likely in hot weather. Open
the fuel filler cap slowly and wait for any “hiss” noise to stop.
Then unscrew the cap all the way.
When you put the cap back on, turn it
to the right until you hear a
clicking noise.

Downloaded from www.Manualslib.com manuals search engine How To Reset the Oil Life Indicator: After the oil has been changed,
press and hold the
“RANGE” and “RESET” buttons between 5 and 60
seconds. Once the buttons are released the “CHANGE OIL SOON”
light will flash 4 times to indicate it has reset to 100. If the “CHANGE
OIL SOON” light comes on for 5 seconds it did not reset. You will need
to reset the system again. The percentage
of oil life remaining may be
checked at any time by pressing the
“RANGE” and “FUEL USED” on
the Fuel Data center.
Engine Block Heater: An engine block heater can be a big help if you
have to park outside
in very cold weather, O°F (-18OC) or colder. If your
vehicle has this option, see “Engine Block Heater” in the Index.
What to Do with Used Oil:
’
A CAUTION:
Used engine oil contains things that have caused skin cancer in
laboratory animals. Don’t let used oil stay
on your skin for very
long. Clean your skin and nails with soap and water, or a good
hand cleaner. Wash or properly throw away clothing or rags
containing used engine oil.
Used oil can be a real threat to the environment. If you change your own
oil, be sure to drain all free-flowing oil from the filter before disposal.
Don’t ever dispose
of oil by pouring it on the ground, into sewers, or into
streams or bodies
of water. Instead, recycle it by taking it to a place that
collects used oil.
If you have a problem properly disposing of your used
oil, ask your dealer, a service station or
a local recycling center for help.

Downloaded from www.Manualslib.com manuals search engine f c.
-1 "
t
Domestic - Turn the housing socket 1/4 turn counterclockwise and
remove it from the headlamp housing.
A
Export - Remove the wiring harness plug.

Downloaded from www.Manualslib.com manuals search engine h
3. Press the bulb
housing lever,
rotate the housing
counterclockwise
1/6 turn and
remove it.
! ..: ’,
5
Y
4. Push and rotate bulb counterclockwise to remove bulb.
Once you have replaced the burned out bulb, just reverse the steps
to
reassemble the taillight.