1992 MAZDA PROTEGE window

POWER WINDOW SYSTEM
Main power window switch operates, but switch
on each door does not operate power window
I Turn ignition switch ON , !
Turn main power window switch ON
Check for battery voltage at terminal-wire (B/L) of main NG _ Check power switch of main power window switch
power window switch connector (Refer to page S-31) OK
Check for battery voltage at terminal-wire (B/L) of switch 3 Repair harness
on each door (Main power window switch-Power window sub-switch) OK
Check power window sub-switch (Refer to page S-32)
23UOSX-013
I PROTEGli HATCHBACK
I
ace
i k
MAIN POWER WINDOW SWITCH
Inspection
Check for continuity between terminals of the switch with an
ohmmeter.
Power switch (ON/OFF)
ON
nl=l= PROTEGE Hatchback
a f h
9
0 0 0 0
0--O: Indicates continuity
Power window switch (Up/Down)
UP ------ o-j0 - -
o-o 00 00
OFF 000 oojo 000 000
I DOWN
0---O: Indicates continuity
s-31

S POWER WINDOW SYSTEM
CD 0 0
L 23UOSX-014
03uosx-04
REAR
POWER WINDOW SUB-SWITCH
Inspection
Check for continuity between terminals of the switch with an
ohmmeter.
Passenger side
-
UP 0 0
0 0
--- -c
I 0
IOWN -,
o---O: indicates continuity
Rear
H: Indicates continuity
POWER WINDOW MOTOR (In power window regulator)
Inspection
1. Disconnect the power window motor connector.
2. Connect battery voltage to terminal (a) and ground termi-
nal (b) of the motor connector, and verify that the motor -I
operates.
3. Reverse the above connections and check for reverse oper-
ation of the motor.
23UOSX-015
S-32

MOLDING, PROTECTOR, GARNISH S
REAR WINDOW MOLDING (PROTEGE)
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
I A
I B 1 I
1. R.H. rear window molding
(with upper and lower joints)
2. L.H. rear window molding
(with upper and lower joints) 3. Upper rear window molding
s-43

S MOLDING, PROTECTOR, GARNISH
REAR WINDOW MOLDING (HATCHBACK)
Removal
Remove in the order show in the figure.
I
^^, .^^.. __-
1. Rear hatch lower trim
Removal . . . . . . . . . . . . . . . . . . . . . . . . ,.. . . . . . . . . . . , 4. L.H. rear window molding
page S-98
2. Lower rear window molding installation nuts
3. R.H. rear window molding
(with upper and lower joints)
s-44
(with upper and lower joints)
5. Lower rear window molding
6. Upper rear window molding

MOLDING, PROTECTOR, GARNISH
installation
Install in the order shown in the figure.
____------.-
- _-.-
S
03UOSX-06(
1. Lower rear window molding
2. R.H. rear window molding
(with upper and lower joints)
3. L.H. rear window molding
(with upper and lower joints) 4. Upper rear window molding
5. Lower rear window molding installation nuts
6. Rear hatch lower trim
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page
S-98
s-45

S WINDSHIELD
WINDSHIELD
PREPARATION
SST
49 0305 870A I 1 For
Tool set, window removal and
installation of
windshield
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
PROTEGC

WINDSHIELD S
PROTECTOR
I SEALANT
mm (in)
.
03uosx-09
GLASS /
SPACER
mm (in
03uosx-1c
PROTEG6
MOLDING MOLDING
SEALANT SEALANT
CROSS-SECTION
mm (in)
03uosx-1c
7. Align the protector on the body, and attach it securely as
shown.
8. Prepare the nozzle of the sealant gun so that it has a flange
that can run along the edge of the glass and a V from which
the sealant can flow. Once the primer is dry, apply the seal-
ant around the entire circumference of the glass to fill the
gap between the dam and the edge of the glass with a ridge
of sealant
12mm (0.47 in) high.
Keep the bead of sealant smooth and even, reshaping it
where necessary with a spatula.
9. Lift the glass into place. Push it in lightly toward the vehicle
to compress the sealant.
Caution
l Open the windows to prevent the glass from being
pushed out by air pressure if a door is closed.
Hardening time of repair seal
I Temperature Surface hardening Time required until car
time can be put into service
I
5% (41 OF) Approx. 1.5 hrs 12 hrs
2ooc (68OF) Approx. 1 hr
4 hrs
35OC (95OF)
Approx. 10 min 2 hrs
10. Align the upper windshield molding on the body as shown,
and push the molding into place along the top.
Note
l Install the molding before the sealant has hardened.
11. Check for water leaks. If a leak is found, wipe the water off
well and add
sealant (BOO1 77 739) where needed.
S-61

QUARTER WINDOW GLASS
QUARTER WINDOW GLASS
COMPONENTS
Removal / Installation
1, Remove in the order shown in the figure.
2. Install in the reverse order of removal.
Note
l Remove overlapping portion of the quarter trim for removal of the A-pillar trim (U.S.) or B-
pillar upper trim (Canada).
7.8-l 1 N.m (80-I 10 cm-kg, 69-95 in-lb)
9
1. Seat belt upper anchor (Canada) 3. Quarter window lock
Removal / Installation . . . . . . . . . . . . . . . . page S-100 4. Quarter window glass
2. A-pillar trim (U.S.)/B-pillar upper trim (Canada) 5. Quarter window hinge
Removal I Installation . . . . . . . . . . . . . . . . page S- 98 6. Pillar molding
S-62