1992 MAZDA PROTEGE window

S
r
FRONT DOOR LOCK AND OPENER
- 1
PROTEGk
03uosx
1. Regulator handle (Manual regulator)
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
2. Inner garnish
3. Front door trim (Manual window)
4. Front door trim (Power window) 5. Inner handle
6. Sealing pad 7.
Door screen S-12 8.
Lock control (Power door 9.
Front door lock assembly 10.
Outer handle 11.
Lock cylinder retainer 12.
Lock cylinder lock) .-,
S-l 4

REAR SIDE WINDOW REGULATOR AND GLASS
REAR SIDE WINDOW REGULATOR AND GLASS
COMPONENTS
Removal / Installation
1. Open the rear door glass fully.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to Removal Note.
4. Install in the reverse order of removal, referring to Installation Note.
Caution
l Remove the door screen carefullv so that it may be reused.
3-9 61-67 in-lb) ,
03uosx-019
1. Regulator handle (Manual window) 9. Center channel, channel protector
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-l 2 10. Rear door glass
2. Rear door trim (Manual window) Removal Note ..,.....,..,................. page S-l 8
3. Rear door trim (Power window) Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-18
4. Inner handle Il. Quarter window glass, weatherstrip
5. Pull handle bracket (Power window) 12. Manual window regulator
6. Rear power window switch 13. Power window regulator
7. Sealing pad 14. Glass run channel
8. Door screen
s-17

S REAR SIDE WINDOW REGULATOR AND GLASS
03UOSX-020
1
LIFT BRACKET
o3uosx-0:
Removal / Installation Note
Rear door glass
Manual window
1, Remove the window regulator roller from the large hole in
the lift bracket to remove the rear door glass.
2. Install in the reverse order of removal.
Power window
1. Remove the window regulator roller from the large hole in
the lift bracket to remove the rear door glass.
2. Install in the reverse order of removal.
s-1 8

REAR DOOR LOCK AND OPENER S
REAR DOOR LOCK AND OPENER
COMPONENTS
Removal / Installation
1. Raise the rear door glass fully to remove the door lock assembly.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to Removal Note.
4. install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
4.2-6.2 N-m
1, Regulator handle (Manual regulator) 7. Sealing pad
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-l 2 8. Door screen
2. Rear door trim (Power window) 9. Lock knob assembly
3. Rear door trim (Manual window) 10. Lock control (Power door lock)
4. inner handle 11, Rear door lock assembly
5. Pull handle bracket (power window) 12. Outer handle
6. Rear power window switch
s-19

POWER WINDOW SYSTEM S
POWER WINDOW SYSTEM
STRUCTURAL VIEW
1, Main power window switch
Inspection ................................... page S-31
2. Power window sub-switch (Passenger side)
Inspection ................................... page S-32
3. Power window sub-switch (Rear)
Removal / Installation .................. page S-l 7
Inspection ................................... page S-32
I i)V”Jh-““I
4. Power window regulator (Front door)
Removal / Installation
Hatchback ................................ page S-10
PROTEGE.. ............................... page S-l 1
Inspection ................................... page S-32
5. Power window regulator (Rear door)
Removal / Installation .................. page S-l 7
Inspection ................................... page S-32
s-27

l POWER WINDOW K-l
MAIN
PUWER WIWCW WWER WihJOW
-/w Y/W a/c x

POWER WINDOW SYSTEM S
Power window system does not operate
(All doors)
I
NG
Check POWER WIND 30A fuse - Repair harness and replace fuse
I
1 OK
Turn ignition switch ON
Check for battery voltage at terminal-wire (B/W) of main NG
power window switch connector Repair harness (Fuse box-Main power window switch)
I
OK
Disconnect main power window switch connector;
check continuity of terminal-wire (B) to ground Repair harness (Main switch-Ground)
OK
- Check main power window switch (Refer to page S-31)
I I
23UOSX-010
Only driver side power window does not operate
( Turn ignition switch ON
Check for battery voltage at terminal-wires (R/B) and
(R/G) of main power window switch connector
UP
DOWN (R/G) wire
~ _ 1 NG -i VB: Battst’y VOltaQe,
Check main power wrndow switch (Refer to page S-31)
OK
Check for battery voltage at terminal-wires (R/B) and
(R/G) of power window motor connector OK
= Check power window motor (Refer to page S-32)
23UOSX-011
Sk29

POWER WINDOW SYSTEM
II
Power window (except driver side) cannot be
operated by main switch
t
Turn ignition switch ON Note l Use only main switch during checking operation.
t
Check for battery voltage at terminal-wires of main
power window switch connector
Switch Condition
Passenger UP
side
DOWN
Rear (LH) . UP
DOWN
Rear (RH) UP
DOWN Terminal Voltage
(G/W) wire Ve
(R/W) wire VB
(G/Y) wire VB
(W/R) wire VB
(L/W) wire VB
(Y/W) wire Ve
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
VB: Battery voltage
NO
- Check main power window switch (Refer to page S-31) NG
___) Repair harness
(Main power window switch-Power window sub-switch)
I OK
Check for battery voltage at terminal-wires of power
window sub-switch connector while operating main
switch
Condition Terminal
UP (R) wire VB
DOWN (G) wire VB
I Check power window sub-switch (Refer to page S-32)
1 OK
Check for battery voltage at terminal wires of power
window motor connector while operating main switch
Condition Terminal Voltage
UP (R) wire
DOWN (G) wire OK
Check power window motor (Refer to page S-32) I 23uosx-012
s-30