1992 MAZDA PROTEGE oil

AIR CONDITIONER U
COMPRESSOR
Removal / Installation
1. Discharge the refrigeration system. (Refer to page U-32.)
2. Remove the undercover.
3. Remove the compressor as shown in the figure, referring to
Removal Note.
4. Install the compressor in the reverse order of removal, referring to Installation Note.
5. Install the undercover.
6. Charge the refrigeration system. (Refer to page U-33.)
u
24-35 (2.4-3.6, 17-26)
N.m (m-kg, ft-it
23UOUX-0
1. Suction hose
2. Discharge hose 3. Compressor
Note
l Immediately plug any open fittings to keep moisture out of the system.
l Apply new compressor oil to the O-rings before connecting the fittings.
l Do not apply compressor oil to the fittings.
l Tightening torque Compressor inlet and outlet: 9.8-l 8 N.m (1.0-l .8 m-kg, 8-l 2 ft-lb)
l Adjust the belt tension to specification.
lb-41

U AIR CONDITIONER
23UOUX-02
Thermal Protector Replacement
1. Removal of discharge valve body
Remove the bolts and carefully remove the discharge valve
body. .-
2. Removal of snap ring and thermal protector
Note
l When removing the thermal protector, do not pull
the harness wires but push the protector out from
its back side.
23UOUX-028 3. Installation of thermal protector
1) Check that the O-ring groove is free from foreign matter.
Apply compressor oil to the O-ring and properly fit it in
the groove.
2) Before installing the thermal protector, check it for con-
tinuity.
23uoux-029 _/”

THERMAL PROTECTOR
23UOUX-03
TH
PR
3) Install the snap ring so that its chamfered edge side faces
the thermal protector (the non-chamfered side faces out-
ward) as shown left.
Make sure the snap ring is seated securely in its groove.
Note
l Install the thermal protector so that its two lead wire
outlet sections are horizontal as shown left.

AIR CONDITIONER U
23UOUX-031 DISCHARGE
VALVE BODY
CYLINDER
1
23UOUX-03
4. Installation of discharge valve body
1) Replace the O-ring and gasket with new ones.
Apply compressor oil to the new O-ring and gasket and
properly assemble them.
Note
l Fit the gasket as shown left while checking that its
top side faces upward.
2) Carefully install the discharge valve body on the com-
pressor and finger tighten the six M6 bolts.
Note
Bolt torquing sequence
l Torque the two socket head bolts (A) to the specifi-
cation.
l Torque the four bolts (B) in a diagonal manner to
the specification.
Tightening torgue: 9.8 N,rn (100 cm-kg, 87 in-lb)
u-45

AIR CONDITIONER U
r 23UOUX-036
L 23UOUX.03
I
L
23UOUX-03 7
Shaft Seal Replacement
1. Remove the armature plate.
Note
l Removal of the clutch pulley and coil is not
necessary.
2. Remove the felt seal and snap ring.
3. Remove the shim(s).
4. Insert the
SST into the compressor aligning the cutout of
the
SST with the groove of the seal plate.
5. Rotate the
SST counterclockwise to make sure that the
cutout is engaged with the seal plate.
6. Pull out the seal plate.
7. Insert the
SST into the compressor aligning the cutout of
the
SST with the metal pawl of the shaft seal.
8. Rotate the
SST counterclockwise to make sure that the cut-
off is engaged with the metal pawl.
9. Pull out the shaft seal.
u-47

U AIR CONDITIONER
23UOUX.04
IO. Lay down the compressor and clean the shaft seal contact-
ing face of the compressor with cleaning solvent.
Caution
l Keep the cleaning solvent and dirt out of the com-
pressor.
l Do not use any cloth for cleaning.
Clean only by rinsing with the solvent.
l Do not spill the refrigerant oil from the compressor.
Refill the same amount of the oil if the oil is spilled
out.
23uoux-039
11. Clean the new shaft seal throughly with cleaning solvent.
12. Lubricate the shaft seal with refrigerant oil (SUNISO 5GS
or equivalent) and install it on the
SST.
Note
l Use only clean refrigerant oil.
l Do not touch the sealing surfaces of the shaft seal
after lubricated.
23UOUX-040
13. Liberally lubricate the compressor shaft with refrigerant oil.
14. Install the shaft seal onto the compressor shaft aligning the
seal case flats with the shaft flats.
U-48

AIR CONDITIONER U
15. Clean the seal plate with cleaning solvent.
Lubricate the seal plate with refrigerant oil (SUNISO 5GS
or equivalent).
Note
l Use only clean refrigerant oil.
l Do not touch the sealing surface of the seal plate
after lubricated.
23lJoux-042
SHAFT SEAL PLATE
14
16. First, slide the seal plate into the compressor by hand as
far as possible.
17. Press the seal plate with grip side of the
SST.
18. Install the snap ring with its chamfered edge inside.
19. Press the snap ring with the grip side of the
SST, then in-
stall the felt seal.
20. Make sure the snap ring is seated correctly in its groove.
21. Install the shim(s).
22. Install the armature plate.
Measure the clearance between the pulley and armature
plate all the way around.
If the clearance is not as specified, add or remove the shim
as required.
Clearance: 0.4-0.5mm (0.016-0.020 in)
Shim
Part number Thickness mm (in)
B455 61 L15 0.2 (0.008)
8456 61 L15 0.5 (0.020)
u-49

U AIR CONDITIONER
RECEIVER/DRIER
Removal / Installation
1. Discharge the refrigeration system. (Refer to page U-32.)
2. Remove the radiator grille. (Refer to Section S.)
3. Remove the receiver/drier as shown in the figure.
Note
l Immediately plug the open fittings to keep moisture out of the system.
4. Install the receiver/drier in the reverse order of removal.
Note
l Apply clean compressor oil to the O-rings before connecting the fittings.
l Do not apply compressor oil to the fitting nuts.
l When installing a new receiver/drier, add compressor oil through the high-pressure pipe port
of the compressor.
Compressor oil: 10 cc (0.61 cu in)
Tightening torque
Receiver/drier inlet: 9.8-20 N*m (1.0-2.0 m-kg, 7.2-14 ft-lb)
Receiver/drier outlet: 15-25 N-m (1.6-2.6 m-kg, 11-18 ft-lb)
1. Receiver/drier .-
u-52

AIR CONDITIONER U
CONDENSER
Removal / Installation
1. Discharge the refrigeration system. (Refer to page U-32.)
2. Remove the radiator grille. (Refer to Section S.)
3. Remove the receiver/drier. (Refer to page U-52.)
4. Remove the condenser as shown in the figure.
Note
l Insert a protector such as cardboard between the condenser and the radiator.
l Immediately plug the open fittings to keep moisture out of the system.
5. install the condenser in the reverse order of removal.
Note
l Apply clean compressor oil to the O-rings before connecting the fittings.
l Do not apply compressor oil to the fitting nuts.
l Remove the protector before installing the radiator brackets.
l When installing a new condenser, add compressor oil through the high-pressure pipe port
of the compressor.
Compressor oil: 30 cc (1.83 cu in)
Tightening torque
Condenser inlet: 15-25 N*rn (1.5-2.5 m-kg, 11-18 ft-lb)
Condenser outlet: 9.8-20 N#m (1 .O-2.0 m-kg, 7.2-14 ft-lb)
1. Radiator bracket
2. Radiator 3. Condenser
23UOUX-01
Inspection
Check for the following and repair or replace the condenser
as necessary.;
1. Cracks, damage, or refrigerant leakage.
2. Bent fins.
3. Distorted or damaged condenser inlet or outlet.
u-53