1992 MAZDA 323 battery

F3 FUEL SYSTEM
t 3EoF3-344
1
FUEL SYSTEM
FUEL PUMP
inspection
Fuel pump operation
1. Connect the diagnosis connector F/P and GND terminals
by using a jumper wire.
2. Remove the fuel filler cap.
3. Turn ON the ignition switch.
4.
Listen at the filler inlet for the operational sou.nd of the fuel
pump.
5. Install the fuel filler cap.
6. If no sound is heard, measure the voltage between the fuel
pump connector (G/R) to a ground.
Voltage: 8attey vo kage
7. If not as specified, check the circuit opening relay and circuit.
8. ff as specified, check fur continuity between fuel pump con-
nector (G/R) and (B).
9. If there is continuity, reptace the fuel pump.
10. If there is no continuity, repair the ground circuit.
f3EOF3.345
13EOF3-346 FUEL PUMP RESlSTORlRELAY
System Operation
1. Remove the rear seat cushion.
2. Measure the voltage at the fuel pump connector terminal
A (G/R).
Voltage
I
Cranking
1 Battery voltage
Ignition switch ON ov 3. If not as specified, perform the following inspections, and
repair or replace as necessary.
l Fuel pump resistor/relay resistance
(Refer to page F3-41.)
l ECU 11 terminal voltage (Refer to page F3-45.)
l Wiring harness and connector
F3-40
ii e -
*
_~ --
C --
A-'

-,
-,
--
--
-1
E
7
2
I
i 3EAR SE
--

FUEL SYSTEM F3
13EOF3.34
c I 13EOF3-364 FUEL PUMP CONNECTOR
/
!NSTALL CLAMPS
I
l nspection
1, Disconnect the resistor/relay connector.
2. Ground the fuel pump resistor relay terminal D.
3. Apply battery voltage and check for continuity as shown.
Terminal C
Continuity between A and I3
Battery voltage applied NO
ov Yes
4. Measure the resistance between terminals E and F.
Resistance : 0.38--0.42Q (at 2O*C {6S°F 1)
PRESSURE REGULATOR
Inspection
Fuel line pressure
Warning
l Before performing the following operation, release
the fuel pressure from the fuel system to reduce the
possibility of injury or fire. (Refer to page F3-21.)
1. Disconnect the negative battery terminal.
2. Connect a fuel pressure gauge between the fuel filter and
the fuel main hose. (install clamps as shown.) , .
I
3. Connect the negative battery terminal.
/t.
4, Start the engine and run it at idle.
5. Measure the fuel line pressure.
Fuel line pressure:
206-255 kPa [ 2.1-2.6 kgflcml, 30-37 psi )
6. Disconnect the upper vacuum hose from the pressure regu-
lator and measure the fuel line pressure.
Fuel line pressure:
304-392 kPa (3.1-4.0 kgf/cm2, 44-57 psi )
F3-41

. !I11
PRESSURE REGULATOR CONTROL SYSTEM F3
13EOF3353
(PRC HIGH TEMP.)
13EOF3-35:
BAl-fERY VOLTA
PRESSURE REGULATOR CONTROL
SYSTEM
SOLENOID VALVE (PRESSURE REGULATOR CONTROL)
Inspection
On-vehicte
1. Start the engine and run it at idle (cold engine).
2. Disconnect the vacuum hoses from the pressure regulator,
and verify that vacuum is felt at each hose.
3. Ground the solenoid valve terminal wire (G/O...low temp.
and G. ..high temp.) by using a jumper wire, and verify that
no vacuum is felt.
4. If vacuum is not as specified, check the solenoid valve.
Solenoid Valve (high and low temp.)
1, Disconnect the vacuum hose from the solenoid valve and
the vacuum pipe..
2. Blow through the solenoid valve from port A.
3. Verify that air flows from port B.
4. Disconnect the solenoid valve connector.
5. Connect battery voltage and a ground to the terminals of
the solenoid v&e.
6. Blow through the solenoid valve from port A.
7. Verify that air flows from the valve air filter.
8. If not as specified, replace the solenoid valve.
.
F3-43

F3 CONTROL SYSTEM
Terminal voltage
Reference date
Vs: Battery voltage
‘em&al Input Output Connected to Test condition Correct voltage Remark
1A - - Battery Constant VB
For backup
18 0 Main relay
Ignition switch OFF ov
(FUEL INJ relay) -
ON
V8
1C 0 lgnitlon switch While cranking Approx. 1 OV
(START) -
Ignition switch ON ov
10 0 Self-Diagnosis Test switch at SELF TEST
Wtth Self-
Checker Lamp illuminated for 3 sec. after ignition Approx. 5V
(monitor lamp) switch OFFdON Diagnosis Check-
er and System
lamp not iltuminated after 3 sec. V8 Selector
Test switch at 02 MONITOR with engine
idling Approx. 5V
Monitor lamp illuminated
Test switch at 02 MONITOR with engine
idling Vi3
Monitor lamp not illuminated
IE - - - - - -
IF
0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2SV
l With Seif-
Checker switch OFF-+ON
Diagnosis
(service code)
Buzzer not sounded after 3 set V0 ’ Checker and
Buzzer sounded Below 2.5V System Selector
l With System
Buzzer not sounded VB Selector test
switch at SELF
TEST
1G 0 igniter tgnition switch ON
ov
-
Idte
Approx. 0.2V
It-l 0
Solenoid valve Ignition switch ON
VB
(wastegate)
Idle
Approx. 2V ’ -
II
0 Fuel pump While cranking
Approx. 1 OV
resistor/relay -
Idle
8etow 1.5V
IJ 0 NC relay Ignition switch ON
VB
A/C switch UN at idle
Below 2.5V
. NC switch OFF at idle V3
-
IK 0 Diagnosis
connector
(TEN terminal) System Selector test switch at
02 MONITOR
System Selector test switch at
SELF TEST V0
-
8elow l*OV
1L - - - - - -
I
1M - - - - -
I -
lr ‘- l-7
f L.-
r
20 20 2M 2K 21 2G 2E 2c 2A IU 1S 10 10 ltvl tK II Ir; tE 1~ IA
1
22 2x 2v 2T ZR 2P 2N 2L 25 2H 2F 20 2B 1V IT 1R tP 1N IL 1J 1H IF 1~ 1~
1
J=3-46 --
4lways 4
--
AIways 4
--
Atways 1
--
Always 1
-a
Always ’
--
Always i
-e
Always I
2.5v
Always
Always (
-m
Always f
-a
Always 1
Always (
--
Always I
2.5V
Always 1
Always t
Always
--

F3 CONTROL SYSTEM
Ve: Battery voltage
Termina
1N ’
10
1P
IQ
IR
IS
1T
tlJ
IV Jnput Outpul
0
0
0
0
0
0
0
0
0 Connected to
Throttle sensor
(idle switch) Test condition
Correct voltage Remark
Accelerator pedal released
Below 1.0V
lgnltlon switch
Accelerator pedal depressed
VI3 ON
Foglrght relay
P/S pressure
switch Fogtight switch ON
Fogfight switch OFF
Ignition switch ON
P/S pressure switch ON at Idle
PIS pressure switch OFF at idle Va
ov
V3
Below 1 .OV
VB -
-
A/C switch A/C switch ON
A/C switch OFF Below 23 Ignition switch
Va ’ ON and blower
motor ON
1 f Ekctrtc cooltng fan Fan operating (coolant temperature over
Below 1 .OV
switch
97OC 1207OF 1 or diagnosis connector
terminal TFA grounded) -
Fan not operating (Idle)
VI3
Blower control Blower control switch OFF or 1st position
.Va
swbtch Ignitton switch
Blower control switch 2nd or hjgher po-
Below 1 .OV ON
sition
Rear window
defroster switch Rear window defroster OFF
Rear window defroster ON Below 1 .OV Ignition switch
V0 ON
Headlight switch
Headfights ON Va
Headlights OFF -
Below 1.OV
Neutral/Clutch
Neutral position or clutch pedal
9eJow I .OV
switches
depressed
Others
Va
7
r u-.
I-I-I
f
2y 2w 2u 2s 20 20 2M 2K 21 2G 2E 2C 2A 1U 1s 10 10 1M 1K 11 rG IE tC ;A
22 2% 2V 2T 2R 2P ZN 2L 25 2H 2F 2D 28 tV 1T ‘IR IF 1N It ;J. IH IF ID 18
i
A
F3-48
-- Alwa@
Always
Always
Always
--
Always
--
Always
--
Always
--
Always
--
Always
(electric
--
Alway<;
--
Always
-e
Afway?;
I .ov
Always
--
Always
--
Alway:;
--

-. _.. . . . . . _ - ._.
-w
CONTROL SYSTEM F3
I .
-.
Ve: Battery voltaae I
Incorrect voltage
Atwafi below 1 .OV
Always VB
Always VS (foglight switch OK)
Always below 1 .OV
Always below 1 .OV
Always Vs
Always
below 23 (blower fan OK)
Always VB (blower fan OK)
Always below 1 .OV
(electric cooling fan OK) -
1-
Possible cause
l Throttle sensor mrsadjustment l Short circuit in wtrrng from throttle sensor to ECU terminal 1 N l ECU malfunction
l Throttle sensor mrsadjustment l Open circuit in wiring from throttle sensor to ECU terminal fN l Open circuit in mnng from throttle sensor to ECU terminal 20
l Foglight relay malfunctron
l Foglrght relay malfunction
l P/S pressure switch maltunctron l Short crrcurt In wrrlng from P/S pressure switch to ECU terminal 1 P l ECU malfunction
l P/S pressure switch malfunction l Open circuit in wlnng from P/S pressure switch to ECU terminal 7 P l Open circuit in wiring from P/S pressure switch to ground
l A/C switch malfunctron l Short circuit tn wiring from A/C switch to ECU terminal 1Q l Poor connection at ECU connector l ECU malfunction
l #C swatch malfunction l Open circuit in wiring from A/C switch to ECU terminal 1Q l Open circuit in wiring from A/C switch to blower control switch
l Open or short circuit in wiring from fan relay to ECU terminal 1R l ECU matfunction
Always below 1 .OV (blower fan OK}
Always Vs (btower fan OK)
Always betow illumination lamp
1 .ov ON when rear
window defroster
switch ON
Illumination lamp
never ON
Atways below 1 .OV (headttghts OK)
l Short circuit in wrrtng from blower control switch to ECU terminal IS l Poor connection at ECU connector l ECU m&function
l Open crrcuit in wrrrng from blower control switch to ECU terminal 1s
l Open or short crrcuit In wiring from rear window defroster switch to ECU
terminal t T
l Open circuit in wiring from ignitron switch to rear window defroster switch l Rear window defroster switch malfunction
l Open or short circuit in wiring from headlight relay to ECU terminal 1 U
Always below 1 .OV
l Neutral switch malfunction l Clutch switch malfunction l Short circuit in wiring from ECU terminal IV to neutral or clutch switch
Always VB
l Neutral switch malfunction l Clutch switch malfunction l Open circuit in wiring from ECU terminal 1V to neutral or clutch swdch l Poor connection at ECU connector
13FOl=3-36 .
F3-49
.:i

F3 CONTROL SYSTEM
Vs: Battery voltage
‘erminat Input Output Connected to Test condition
Correct voltage Remark
2A’ - - Ground (i nlector) Constant CIV -
26 - - Ground (output) Constant ov -
2C - - Ground (CPU) Constant ov -
2D - - Ground (input) Constant ov -
2E 0 Distributor Ignition switch ON QV or 5v
{NE-slgnal) -
f
r ldte
Approx. 2V
2F - - - -
- -
2G 0 Dstributor Ignition switch ON
ov or 5v
(G signal)
ldte Approx. 1.5V
a-l -I- - -
- -
21 - - - - - -
23 0 Knock control unit Idle Approx. 4.W -
I
2K 0 Throttle sensor/ Constant 4.5--5SV
Airflow meter
-
2L cl
2M 0 Speedometor
sensor
Throttle sensor Ignition switch UN
Accelerator pedal released
Accelerator pedal fully depressed 0 or 5V
Approx. 0.W
Approx. 4.W
-
2N 0
20 0
2P 0
2Q 0
2R Oxygen sensor Ignition switch ON ov
Idle (cold engine) ov
Idle (after warm-up) o- 1 .ov -
Increasing engine speed (after warm-up) 0.5-l .ov
Deceleration o--0.w
Airflow meter ignition switch ON Approx. 3.W
-
Idle Approx. 3.OV
Intake air Ambient air temperature 2O*C (68*F) Approx. 2.5V In arrflow meter
thermosensor
Water Engine’cooiant temperature 20°C (68OF) Approx. 2.W
thermosensor -
After warm-up Below 0.5V
0 Turbocharge Ignition switch ON VS
indicator -
7
r u-l 7 c Ul I-'
2y ?A’ 2u 25 20 20 2M 2K 21 ?G 2E 2C 2A 1u 1s 10 10 1M ?K 11 1G 1E 1C 1A
22 2x zv 2T 2R 2P 2N 2L 2J 2H 2F 20 28 1V 1T tR tP 1N IL 1.1 1~ qF 10 1~
F3-50
L --
4b&e (
--
Alway:
-a
--
Always
--
--
--
Always
--
Always
--
Below L
-I
--
Always
--
Alway:,
Alway:;
Alway:;
--
Alway:;
--
Always
--
Always
--
Always
Always

CONTROL SYSTEM F3
VS: Battery voltage
Incorrect voltage Possible cause
Ab&e OV
l Poor contact at ground terminal l Open circuit in wiring from ECU to ground
Always approx. OV or approx. 2V
l Refer to Code No. 02 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
Always approx. OV or approx. 1.5V
l Refer to Code No, 03 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV
Always OV
- -
l Refer to Code No. 05 Troubleshooting
(Refer to 323 4-Wheel drive Workshop Manual (1229-10-891))
l Short circuit in wiring from ECU terminal 2K to throttle sensor, or airflow
meter
l Poor connection at ECU connector l ECU matfunctlon
Below 4.5V or above 5.5V
-
l ECU matfunction
l Refer to section 1
Always OV
l Throttle sensor malfunction l Short circuit in wlnng from ECU termrnal 2M to throttle sensot l Poor connection at ECU connector
. ECU malfunction
Always approx. 5V . Throttle sensor misadjustment
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always constant
l Open circuit in wiring from ECU terminal 2M to throttle sensor
. Open circurt in wiring from ECU terminal 2K to throttle sensor
l Open circuit in wiring from ECU terminal 2D to throttle sensor
Always above 1V 1 . Throttle sensor mtsadjustment
Always OV (after warm-up)
Always approx. IV (after warm-up)
l Refer to Code No. 15 Troubleshooting
(Refer to 323 Workshop Manual (1203-I O-89F))
l Refer to Code No.17 Troubleshooting
(Refer to 323 Workshop Manual (1203-lo-89F))
Always OV or approx. 5V
l Refer to Code No. 08 Troubleshooting
(Refer to 323 Workshop Manual (t203-lo-89F))
Always OV or approx. 5V
Always OV or approx. 5V
l Refer to Code No. 10 Troubleshooting
(Refer to 323 Workshop Manual (l203-lo-89F))
l Refer to Code No. 09 Troubleshooting
(Refer to 323 Workshop Manual (1203-10.89F))
Always OV
I
l Indicator broken l Open or short circuit In wiring from ECU 2R to ignition switch
13EOF3-36;
F3