1992 MAZDA 323 radiator cap

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

The following chart shows interchangeability of the main parts of the previous BP DOHC Turbo engine
and the new BP DOHC Turbo engine for 4WD models.
S ymiols: 0 _. lnterc hangeable X . . . Not Interchangeable
Part name tnterchangeability
Remark
Cytlnder head 0
Camshaft 011 seal 0
Cvllnder head bolt 0
CB :
Cyh nder
blcck
related
Crankshaft
related
Timing belt
related
Valve
related
Lubrication
system
related Cylrnder head gasket 0
Wnder head cover 0
Cylinder head cover gasket
Cylinder block
MaEn bearina cao 0
0
0
Ma+n bearino suo~oFt elate I
0 I ” ,I I
Oil pan
Timrno belt cover I X
0 I
Turbocharger oil return pipe hole increased from
13mm IO.51 in) to 17mm IO.67 in)
Seal elate
Front orl seal I 0 I
I I 0
1
Rear 011 seal 0
Crankshaft 0
Marn bearina 0
Thrust bearing
Connectmg rod
Connecting rod beartng
Piston 0
;J
X
Shape different
Piston skirt shortened
I Piston pm cl
Tw
X Sectional shape different
Piston rrng Piston ring end gap increased from 0:?5--0.30mm
Second
X ~0.006-0.011 in ) to 0.35-0.50mm IO.01 4-0.019
in ] (Measured In cylinder)
Crankshaft pulley Shape different
Rear cover ;5
Flywheel
I 0
Flywheel bolt 0
Tbmlng belt 0
Timing belt crank pulley 0
Camshaft pulley 0
Timing belt tensioner and spring
0
Idler 0
Camshaft 0
AA
Valve Intake
Exhaust
cl
0
X Metallic sodium-filled valve
Valve spring Intake
I 0
and seat
Exhaust 0
Vatve wide I 0
Valve seal
Oil pump 0
Oil pump gasket 0
oil strainer 0
Oil strainer gasket 0
Oil cooler
X Heat dissi patlon capacity increased
Oil jet
Oil filter Shape different
1 Water pump 0
Coohng Thermostat 0
system
related Radiator 0
Cooling fan 0
I 3EO32.304
BZ-3.

TECHNICAL DATA TD
Engine
Item BP DOHC turbo
Engine oii
Total (dry engine} 4.0 14.2, 3.5)
Capacity
L IUS qt, Imp qtl Ott pan 3.6 (3.8, 3.2)
011 filter 0.17 (0.18, 0.15)
Grade API Service SD, SE, SF or SG
Above 30°C (86*F) SAE 40
O*C-40*C ~32°F-1040F 1 SAE 30
-1 OOC--2O*C [ 14OF-68OF ] SAE 2OW-20
Viscosity Above -10% [14*Fj SAE ZOW-40 or 2OW-50
number -25*C--3O*C I-1 3OF-86OF ] SAE 1 OW-30
Above -25OC (-13*F1 SAE low-40 or low-50
Below O*C (32*F] SAE 5W-30
Below -2O*C I-4*F] SAE 5W-20
COOLING SYSTEM
L
item
Zooling method - 1 Engine
BP DUHC turbo
I Water-cooled, forced crrcutation
water pump
Type
mpeller diameter
Number of impeller blades
Speed ratio
tiater seal type
rhermostat
bfpe
Opening temperature
Full-open temperature
Full-open lift mm [in)
OC (OF)
*C j*FJ
mm (in] Centrifugal, V-belt driven
75 12.95)
6
1 : 1.05
Unified mechanical seal
Wax, two-stage
Marn: 86.5-89.5 [ 788-I 93 1
Sub: 83.5-86.5 [182-i 88)
loo (212)
Main: 8.0 (0.31 1 min.
Sub: 1.5 IO.061 min.
Radbtor
Type
Cap valve opening pressure kPa { kgflcm2, psi)
Cooling circuit checkrng pressure kPa ( kgflcm2, psi 1
Cooling fan
Type
Number of blades
Outer diameter mm {in 1
Capacity w-v
Current A
Water thermoswitch
OFF-+ON “C 1°F) 1
Radiator thermoswitch
OFFdON OC (OF]
Coolant
Capacity LWS qt,
Imp qt) Coolant protection
Above -16*C (3OF]
Antifreeze solutron
.Above -26*C t-1 5*F ) -
Above -4UOC I-40°F) Corrugated fin
74-103 {0.75--1.05, 11-15)
103 11.05, 15)
Electric
5
340 (13.41
160-12
Hi: 13.3+ 10% max., Lo: 8.8+ 10% max.
97 f207)
105 [221)
6.0 16.3, 5.3)
Specific gravity at 20*C (68*f)
1.054
1.066
1.078 -.ep
1