1992 MAZDA 323 ESP

TROUBLESHOOTING GUlbE F3 1
14 IDLE MOVES UP AND DOWN/IDLE HUNTS
IESCRLP-
l Engine speeds up and down periodically at idle
UON
TROUBLESHOOTING HINTS]
B Idle switch (En throttle sensor) OFF at idle
3 Air leakage
3 Fuel injection amount Inconstant
. Poor contact point inside airflow meter
9 Poor ignitron
rEP[ INSPECTION
I is “00” displayed on Self-Dragnosis Checker
with ignrtron swatch ON?
SYSTEM SELECT: i I ACTfON
Yes Go to next step
NO Service Code No. displayed
Check for cause (Refer to specified
check sequence) c=;r page F3-16
“86” flashes

Check ECU terminal IF vottage csr page F345
Voltage: Battery voltage
W: SELF TEST (ignition switch ON)
SELECT SW: A
.d P/ e If OK, replace ECU CT page F3-3
c3 If not OK, check wrrjng
(ECU - Self-Dlagnosls Checker)
2 Is intake manrfold vacuum correct at idle? Yes Go to next step
Intake manifold vacuum:
More than 450 mmHg { 17.7 inHg )
No Low vacuum
Check for air leakage at intake air
system
3 Is air cleaner element clean? Yes Go to next step
No Replace abr cleaner element
4 Disconnect each hrgh-tension lead at idie; does Yes Go to next step
engine speed decrease equally at each cylinder?
No Go to Step 8
5 Are ECU terminal voltages OK? Yes Go to next step
(especially 20, 2Q, 20) -
rI7 page F345 No
Check for cause
6 Connect System Selector to diagnosis connector Yes Go to next step
and set Test Switch to SELF TEST; is ignition
timing at idle correct after warm-up?
Ignition timing (BTDC): f 0 f la
No Adjust ignition timing
._
. F3-33

TROUBLESHOOTING GUiDE F3
15 ENGINE STALLS ON DECELERATION
IESCRIP-
l Engrne unexpectedly stops running dunng or after deceleration
[iON l Idle condition normal.
TROUBLESHOOT1NG HtNTS]
ingrne speed drops too much when releasrng accelerator
3 Idle-speed misadjustment @I Loose connector disconnected by force of deceleration
3 Fuel-cut contrd malfunction
TEP lNSPECTlON ACTION
1 1s idle condition normal? Yes Go to next step
tdle speed: 800 f 50 rpm (in neutral)
NO Adjust or perform Troubleshooting, Nos.
8-I 1 “ROUGH IDLE”
(Refer to Workshop Manual
(1203-I o-89F))
2 Is “00” displayed on Self-Diagnosis Checker Yes Go to next step
with ignition switch ON?
SYSTEM SELECT: 1 NO Service Code No. displayed
Check for cause (Refer to specified
check sequence) ET page F3-16
“88” flashes
Check ECU termrnal 1 F voltage
Voltage: Battery voltage
(ignition switch ON) r;r page F346
W:SELFTEST
e If OK, replace ECU CI page F3-3
4 If not OK, check wirtng
(ECU - Self-Diagnosis Checker)
3 Does Self-Diagnosis Checker Monitor Lamp with Yes Go to next step
lgnttlon switch UN show that switches operate
correctly?
NO Lamp not ON or OFF with specified
switch
Check for cause (Refer to specified
check sequence)
W: SEtF TEST Lamp slways ON
Check wiring between
(ECU terminal 1 D - Self-Diagnosis
Checker)
4 Are ECU ?erminal voltages OK? Yes Go to next step
(especially IV, 20, 20, ZU, 2V.
and 20) v page F346 No
Check for cause
5 Check for poor connection of foltowing parts YC?S Repair or replace
l ignrtion coil l Igniter l Olstribdor l High-tension lead
NO Go to next step l Injector. l Injector resistor l Ctrcuit-opening relay . l ECU
F3-35

F3 TROUBLESHOOTING GUIDE
STEP INSPECTION ACTlON
6 Is dashpot correctly adjusted? Yes Go to next step
c
Dashpot set speed: Approx. 3,500 rpm
No Adjust dashpot
7
Try known good ECU; does condition
Improve?
w page F3-3
13EOF3-336
16 ENGINE STALLS SUDDENLY (INTERMITTENT)
DESCRIP.
l Engine intermittently stops running
TION l Before stalling, engine conditron is OK
TROUBLESHOOTING HINTS]
@ intermittently no spark or no fuel injection caused by ve-
hlcle vibratron, acceleratton, or deceleration
l Poor connectlon in wiring harness
iTEP INSPECTION ACTfON
1 Is “00” displayed on Self-Oiagnoss Checker Yes Go to next step
with lgnltlon swrtch ON?
NO Service Code No. displayed
Check for cause (Refer to speclfled
check sequence).
Note CT page F3-16
l When checking wiring harness and
connectors, tap, move, and wiggle
suspect sensor and/or harness to
recreate problem
“88” flashes ’
Check ECU terminal IF voltage
Voltage: Battery voltage
{ignition swttch ON) w page F3-45
4 If OK, replace ECU
4 If not OK, check wiring
(ECU - Self-Diagnosis Checker)
2 Check for poor connection of foliowrng parts
Yes Reparr or replace
l lgnltfon coil l Igniter l Distributor l t-flgh-tensron lead
No Go to next step l Injector l Injector reststor l Circutt-opening relay l ECU
3 Are ECU terminal voltages OK? Yes Go to Troubleshbotrng No. 2
(especially 16, 2A, 2B, and 2C) .“CRANKS NORMALLY BUT WILL NOT
w page F3-45 START (NO COMBUSTION)”
w page F3-20
Note
. No Check for cause
l When. checking voltages, tap, move, and
wiggle harness and connector to recreate
problem
* lrlrl m-7
F3-36
7.8-l

N OUTLJNE
UUTLJNE
OUTLINE Of CONSTRUCTION
l EncJine speed sensing power steering (ESPS) is standard equipment for all models. The construction and
operation are basically the same as for previous models.
l The lock-to-lock specification of the steering wheel is reduced from 2.76 to 2.51.
13EONX-302
SPECIFICATIONS
hem Specifications
Steermg wheel Outer diameter mm {in] 370 { 14.57)
Lock-to-lock turns :i-‘~~:~.~~~~~~:~~;~~~~ :;‘:.. .‘:I .:::::.::~::::,:.:::.i: ,,,,.,:, :‘,:,,.:,: .,: I. . ..- :.~6:.n.:::;,:~~:~~~~~~~.~::~,:~:.: :: :
” .: ‘-.: .:.:::~:‘::.‘.::‘:‘:.I;:.‘,.: >.. .: :” 3 :. ,;:.+..i<.I. ‘_ : ; t:
. . ..: :: ::.:. .:::. ::r .;
. . . . . . . . . .y : :.: ,. .: ,_ : ., :
Me Collapsible
Steering shaft and joint Joint type
Tilt stroke
J 2-cross joint
mm {in] 30 11.18)
Type Rack-and-pinion
I
Steering gear Gear ratio
Rack stroke mm [in] 00 (infinite)
121 f4.761
Capacity
Power steertng fluid 1 (US qt Imp qt) 018 (0.85, 0.701
We ATF DexrorPlI or M-ID
,
Shaded area rndicates new specrfcatlon. t3EONX-303
N-2