1992 MAZDA 323 bonnet

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

S
BODY
INDEX . . . . . ..*.I........**........*.~*.~............*.......
s- 2
OUTLINE ..................................................
s- 3
UUJLINE OF CONSTRUCTION ..................
S- 3
BONNET BULGE
....................................
s- 3
RADIATOR GRILLE ................................. s- 4
FRONT BUMPER .................................... s- 4
REAR SKIRT ...........................................
s- 6
WHEEL ARCl-i MOLDING .........................
s- 5
( SERVICE j
SUPPLEMENTAL SERVICE fNFURMATION.. S- 6
BONNET BULGE
.......................................
s- 7
COMPONENTS ....................................... s- ‘7
FRONT BUMPER
.......................................
s- 8
COMPONENTS .......................................
s- 8
REAR SKIRT .............................................
S-10
COhiIPONENTS .......................................
S-10
Wt=fEEL ARCH MOLDING ............................
S-l 1
COMPONENTS .......................................
S-l 1
13EOSX301

S INDEX
INDEX
1. Bonnet bulge
Removal ! Installation _. __. . . , , . . l.. . .__ page. S-
2. Fro.nt bumper
7 Removal / Installation
. . . . . 1 . . . . . . . ,‘... page S-
Disassembly / Assembly 8
. ..a I........
page S- 9
s-2 3. Rear skirt
Removal / t’nstaltation 4. Wheel arch molding .....n.....ba..... page S-l 0
Removal / Installation
. .-. . . , , ..‘. .-. page S-l 1
OUTLINE
l The exteric
bofiy.
OUTLtNE 01
i BONNET BUt
l Bonnet bulg
a high-qualit

l The exterior parts are designed to emphasize the function and appearance of the superbly proportioned
body.
: OUTtlNE OF CONSTRUCTION
1 xosx.303
.c
Bonnet bulges are provided in bonnet
. . . . . . . . . . . . ..I................~.....
s-3
A large, body-colored front bumper fascia is adopted., , ..,..,.... S-4
Wheel arch moldings are fitted to fenders . . . . . . . ,..*. l.. . . . . . . . . . . . . . . . . . S-5
- Air inlet area of radiator grille is enlarged
................................. S-4
- Bumper mesh is provided in front bumper
..............................
s-4 Rear skirt is attached under rear bumper.. ............................... S-5
13EOSX-304 BONNET BULGE
l Bonnet bulges are fittGd to the bonnet to match the dynamic appearance of the vehicle and to give it
a high-quality look.

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if

BONNET BULGE S
BONNET BULGE
COMPONENTS
Rem&at ! Installation
1. Removal in the order shown in the
figure.
2. Install in the reverse order of removal.
I . Bonnet butge’