1992 MAZDA 323 height

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

TD TECHNICAL DATA
ENGINE (BP DOHC turbo)
Item m
Type BP DOHC turbo
Gasoline, 4-cycle
Cvlinder arranoement and number
1 In-line 4-cylinders
I
I Combustion chamber
I Pent&of
Valve system DOHC, belt-driven 16 valves
Bore x Stroke mm {in] 83.0 x 85.0 (3.27 x 3.35)
Total piston drsplacement cm3 Icu in] 1,839 {112.2)
Compression rat!0 8.2
1 Standard 1,127 111.5, t641-300
Compression pressure
kPa ( kgf/cm2, psi 1 -rpm
Valve timing Mintmum
Maximum drfference between
each cylinder
IN Open BTDC
Close ABDC
EX Open BBDC
Close ATDC ! 785 {8.CI, 114]-300
196 12.0, 28)
2*
51°
590
8*
Valve clearance
I I ---- f IN
mm linl EX I 0: Maintenance-free
0: Maintenance-free
Cylinder head
Height mm finI 133.8-l 34.0 { 5.268-5.276 1
DIstortion mm [in] 0.10 !0.004] max.
GrindIng mm [in) 0.10 {O.O04t max.
Cylrnder head-to-l-LA clearance rqm [ In] Standard 0.025-0.066 IO.001 O-0.0026 ]
Maximum 0.18 10.0071 1
Valve and valve guide
Valve head diameter
mm Ml IN 32.9-33.1 { 1.295-l -3031
27.85-28.15 ! 1.096-l .I08 I -
tN
0.025-0.060 ~0.0010-0.6024)
Valve stem-to-guide clearance mm {in] EX 0.030-0.065 (0.0012-0.0026)
Maximum
0.20 IO.008 1
Guide projection (Height “A”} mm IIn) Ex
Vslve seat 18.3-18.9 {O-720-0.744)
18.3-18.9 { 0:720-0.744 ] rem
Fanshaft -
;am height
Journal diamr
Camshaft be5
Camshaft run’
Camshaft enc
Cylinder b6
Height 1
Distortion
Grinding
Cylin’aer bore
Cylinder Borg
Piston -
Piston diams
Measured at
bore axis ant
(0.433 in) b
groove
Piston to cyi
Piston ring
ThickneSS
End gap (MJlt
Ring groove
Piston ring4
TD-2

TECHNICAL DATA TD
Hem
Camshafi
Engine
BP DOHC turbo
IN Standard
Cam height mm 1 in) Wear limrt
EX Standard
Wear llmrt
Standard
Journal diameter mm 1 In] (M.1 --NW
Out-of-round
Standard
Camshaft bearing oil clearance mm { in ] (No. f-440.5)
Maximum
Camshaft runout mm {in)
Camshaft end play mm Iin] - Standard
Maximum
Winder block
Height mm {in)
Distortion mm {in]
Grinding mm (in)
Cylinder bore diameter Standard size
mm Iin) 0.25 [ 0.010) oversize .
0.50 [ 0.020 ] oversize
Cylinder bure taper and out-of-round mm [in]
Piston
44.094 { 1.7360 ]
43.894 f 1.7281 ]
44.603 [ 1.7560)
44.403 [ t .748t ;
X940-25.965 I 1.0213-l .0222 j
0.05 (0.002] max.
0.035-0.081 [ 0.0014-0.0032 )
0.15 (0.006)
0.03 (0.0012 1 max.
0.07-O. 19 [ 0.0028-0.0075 1
0.2 IO.008 1
221.5 (8.720)
0.15 [0.006) max.
0.20 [0.008] max.
83.006-83.013 13.2679-3.2682 ]
83.256-83.263
13.2778-3.2781 ]
83.506-83.513
( 3.2876-3.2879 )
0.019 [0.0007) max.
Piston diameter Standard size 82:954-82.974 13.2659-3.2667 1
Measured at 90° to pin
bore axis and 11 .Omm
oversize 83.21 I-83.217
10.433 in] below oil ring 0.25 j 0.010 ]
13.2760-3.2763 ]
groove mm {In)
0.50 { 0.020) oversize 83.461-83,467
{ 3.2859-3.2861 )
Piston to cybnder clearance
Piston ring
mm (in) Standard 0.039-0.052 [ 0.0015-0.0020 ]
Maximum
0.15 [0.006]
Thickness mm {in] Top
Second
, Top
End gap (Measured in the cylinder) Second
mm I in 1 Oil (rail)
Maximum
TOP
Ring groove width in piston
mm (in) Second
r
Oil
Piston ring-to-ring groove clearance TOP
mm (in] Second
Maximum
Piston pin
Diameter mm {in)
Piston-to-piston pin clearance mm iin]
Connecting rod bush-to-piston pin clearance mm Iin)
Connecting rod and connecting rod bearing
Length (Center to center) mm {in] 1
Bending mm [in]
Small end bore (Bush inner diameter) mm [in)
Big end bore mm {in)
Bfg end width mm [in) 1
Standard
Connecting rod side clearance mm I in 1 Maximum I
Crankshaft
Crankshaft iunout mm {ln) 1.470-l ,495 { 0.0579-0.0589 ]
1.47-l -49 [0.0579-0.0587 )
0.15-0.30 [ 0.006-0.012 1
0.35-0.50 { 0.014-0.019 1
0.20-0.70 (0.008-0.028 )
1.0 [0.039)
1.520-I .535 f0.0598~9.0604 f
1.52-l .54 ~0.0598-0.0606)
3.02-3.04 (0.1189-0.1197 1
0.025-0.065 { 0.001 O-0.0026 ]
0.03-OXI7 (O.O012--0.0028)
._
0.15 (0.006]
19.987-l 9.993 (.0.7869-0.7871 )
-0.005-0.013 { -0.0002-0.0005 1
O.Ql O-0.027 ~0.0004-0.0011 )
m D 132.85-132.95 (5.230-5.234 1
0.075 ( 0.0030 ] max./50 I1:97 ]
20.003-20.014 ( 0.7875-0.7880 1
48.000-48.016 [ 1.8898-l 48904 ]
21.838-21.890 (0.8598-0.86t81
0.11 O-O.262 f 0.0043-0.0103 1
0.30 [0.012)
0.04 (0.0016)
mdx.
TCI rl

TD TECHNICAL DATA
CLUTCH
Jmn -
Clutch control
Clutch oedat Engine/Transaxle BP DOW turbo
G25MX-R {G5MX-R)
Hydraulic Type I
Suspended
Pedal ratio mm [in) 6.55
Full stroke mm {in] 135 t5.311
Height (With carpet) mm [in] 196-204 (7.72-8.03 1
Free play mm (in] 5.5-l 7.4 {0.22-0.69 ]
Distance to carpet when clutch fully
disengaged mm [in) Minimum 41.0 (1.61 ]
Flywheel
Runout limit mm {in] 0.200 [ 0.0079)
Clutch disc
1
, Type I Single dry plate
Runout limit mm (in) 0.700 [ 0.0276 )
Wear limit mm {in] 0.3 [ 0.012 ] from rivet head
Outer diameter mm {in] 230 {9.05)
Inner diameter mm {in) 155 i6.10)
Facing thickness mm [in] Flywheel side
I 3.5 (0.14)
Pressure elate side 3.5 10.141
Clutch cover
Type
Set load
Ctutch fluid
Type I
N [kgf, Ibf) 1
I Diaphragm spring
5,494 1560, 1,232)
SAE J1793 or FMVSS116 DOT-3 MANUAL TRANSAXLE AND TRANSFER
SpecMcation
Transaxle type
Transaxle control
Transaxle shift control
Syncromesh system G25MX-R (G5MX-R)
Floor shift
Cable
Forward: Synchromesh
Reverse: Seiective sfidina and svnchromesh
I 1 st 3.454 a
2nd 1.833
3rd 1.310
Gear ratio
4th 0.970
5th 0.717
Reverse 3.166
Final gear ratio I . 4.214
Speedometer gear ratio (Driven gear/drive gear) 1.045 (23122)
Grade API service GL-4
011 Viscocity AkeaSQn: ATF Dexron@II or M-ID
Above -l8*C (OOF): SAE 75W-90
Capacity L {USqt, Imp itI 2.6 12.7, 2;2]
Runout
Primary shaft gear runout
Secondary shaft gear runout mm {in) 0.050. [ 0.0020 ]
mm [in] 0.015 { 0.0006 ]
Clearance
1st’ (Gear inner dia. -shaft puter dia)
2nd (Gear inner dia. -shaft outer dia)
3rd {Gear inner dia. -shaft outer dia)
4th (Gear inner dia. -shaft outer dia)
5th (Gear rnner dia. -shaft outer diaj mm {in] 1 0.030-0.080 { 0.0012-0.0~3 11
mm {in) 0.030~0.08C (-0.0012-0.0031 1
mm (in) 0.030-0.080 I 0:0012-0.003i 1
mm [in] 0.030-0.080 [ 0.0012-0.0031 ]
mm [lnl 0.030--0.080 ~0.0012-0.0031 1
1. TD-8
Lern
l-2 sift for
3-4 shift fri
5th shift f;t
Reverse iti
Thrust cli
1st gear
2nd gear
3rd gear
4th gear
5th gear
. .
Primary St
Seconda:
Center ci
Type :
Number
c
Number (
Number r
Number ;
Bearing ;
Bearing
1
End plai
Ring get
End pi&i
Sun gea
frltnsfe~
Final g&f
Number

TD TECHNICAL DATA
Hem Engine
SP DOHC turbo
Note ) I
1 st and 2nd
Synchronizer ring outer diameter
’ I 67.7 I2.665)
mm [in] 3rd and 4th 67.7 12.665 )
5th and reverse 55.7 t2.192)
Synchronizer key dimension 1st and 2nd @ 19.0 {0.748], 04.3 (0.171, 05.0 10.20)
mm [in] 3rd and 4th @ 17.0 10.669J, 04.3 (0.171, @ 5.0 lO.20)
5th and reverse 0 17.0 10.6691, m4.3
10.171, @I 5.0 fO.201
PROPELLER SHAFT
Item
length
Outer diameter Engineflransaxie Model BP DOHC turbo
G25MX-R (GSMX-R)
Front 834.3 { 32.85 ]
mm fin] Center 584 122.99)
Rear
I 437 { 17.20)
Front 75 (2.95)
mm { in] Center 57 12.24) f
Rear 57 12.241
FRONT AND REAR AXLES
Item Specifications
Front driveshaft

Jomt type Inside Double oftset joint
Outside Bell jotnt
Length of joint (between center of joint) mm { rn t - Right 392 (15.4)
left 306 (0.83 ]
Shaft diameter mm {in] 21.0 to.831
I
Rear driveshaft
Joint type Inside 1
Outside 1
Length of joint (between center of joint) mm [in ] ’ Right
Left
Shaft diameter mm (in)
J&t shatt
Length of joint
Shaft diameter
Front axle
Bearing play axial direction mm [in] 1
Rear axle
Bearing play axial direction mm lin] 1
Rear differential (viscous limited slip differential) Double offset joint
Bell joint
519.5 (20.5 ]
489.5 [f9.3]
21.0 IO.831
357.2 1 t4.11
21 .O (0.83 )
0.050 IO.002 ]
0.050 (0.002 ]
*
Reduction gear
Different ia gear
Oifferential ratro
Number of teeth
Flurd
L Ring gear
Drive .pinion gear
Grade
Viscosity Above -18*C fO*F ]
Below -18*C lOoF)
, Capacity
L fUS qt, Imp c$l Hypoid gear
Straight bevel gear
3.909
43
11
API Service GL-5
SAE 90
SAE 80W
0.65 lQ.69, 0.571 STEERING SI
1 Free olav 8RAKING SY
Brake type
Brake pedat
Height
Free play 1
Reserve travel
Clearance whet
Master cylinde
Master cylinder
Front disc brai
. Tyl?e
Thickness of p&
Thickness of pa