1991 MITSUBISHI MONTERO boot
[x] Cancel search: bootPage 306 of 1333
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Clamp corroded, not
reusable ............... 1 ............ Suggest replacement.
Connected incorrectly ... A ................. Require repair.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Corroded, not affecting
structural integrity ... .. ........ No service suggested or
required.
Cracked ................. A .. Require repair or replacement.
Fitting type incorrect
(such as compression
fitting) ............... B ............ Require replacement.
Flange leaking .......... A .. Require repair or replacement.
Insufficient clamping
force, allowing hose to
leak ................... A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Melted .................. 1 .. Suggest repair or replacement.
Missing ................. C ............ Require replacement.
Outer covering damaged to
the extent that the inner
fabric is visible ...... A ............ Require replacement.
Protective sleeves
damaged ................ 2 . Suggest replacement of sleeves.
Protective sleeves
missing ................ C . Require replacement of sleeves.
Restricted, affecting
performance ............ A .. Require repair or replacement.
Routed incorrectly ...... 2 ................. Require repair.
Swollen ................. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Type incorrect .......... 1 .. Suggest repair or replacement.
\
\
\
\
\
\
\
COOLERS
See TRANSMISSION COOLERS .
CV JOINTS
CV JOINT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bearing, bushing or seal
surface worn, affecting
performance ............ A .. Require repair or replacement.
Boot clamp broken ....... A ... Require repair or replacement
of clamp.
Boot clamp loose ........ A ... Require repair or replacement
of clamp.
Boot clamp missing ...... C ... Require repair or replacement
of clamp.
Boot leaking ............ A . Require replacement of CV boot.
Boot surface cracked,
Page 307 of 1333
not leaking ............ 2 . Suggest replacement of CV boot.
Cage broken ............. A ... Require repair or replacement
of CV joint.
Housing damaged to the
extent that it no longer
performs its intended
function ............... A ........... (1) Require repair or
replacement of CV joint.
Housing worn to the extent
that it no longer performs
its intended function .. A ........... ( 1) Require repair or
replacement of CV joint.
Holes elongated ......... A ............ Require replacement.
Internal parts binding .. A .. Require repair or replacement.
Internal parts worn ..... A .. Require repair or replacement.
Lubricant missing ....... C ... Require cleaning, inspection,
and repacking of CV joint.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Housing assembly may appear blue in color from normal
manufacturing process of heat-treating the housing.
\
\
\
\
\
\
\
DIP STICK TUBES
DIP STICK TUBE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A .. Require repair or replacement.
Checkball missing ....... C .. Suggest repair or replacement.
Cracked ................. A .. Require repair or replacement.
Hold down bracket
broken ................. A .. Require repair or replacement.
Hold down bracket
missing ................ C ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
DIP STICKS (FLUID LEVEL INDICATORS)
DIP STICK (FLUID LEVEL INDICATOR) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Compressed .............. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Modified ................ A ............ Require replacement.
Stretched ............... A .. Require repair or replacement.
\
\
\
\
\
\
\
DOWEL PINS, GUIDES AND PILOT HOLES
DOWEL PIN, GUIDE AND PILOT HOLE INSPECTION \
\
\
\
\
\
\
Page 308 of 1333
Condition Code Procedure
Application incorrect ... B .. Require repair or replacement.
Cracked ................. A .. Require repair or replacement.
Distorted ............... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Positioned incorrectly .. B .. Require repair or replacement.
Stepped ................. A .. Require repair or replacement.
Worn to the extent that it
no longer performs its
intended function ...... A .. Require repair or replacement.
\
\
\
\
\
\
\
DRIVE SHAFT FLANGES
See COMPANION FLANGES .
DRIVE SHAFTS AND HALF SHAFTS
DRIVE SHAFT AND HALF SHAFT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. C .. Require repair or replacement.
Bearing cap bore
distorted .............. A .. Require repair or replacement.
Bent .................... A ............ Require replacement.
Bolt holes elongated .... A .. Require repair or replacement.
Bushing or seal surface
worn, affecting
performance ............ A .. Require repair or replacement.
Leaking through soft yoke
plug ................... A ... Require repair or replacement
of soft yoke plug.
Out of balance .......... A .. Require repair or replacement.
Retainer strap bent ..... A .......... Require replacement of
retainer strap.
Slip yoke broken ........ A ............ Require replacement.
Splines worn, affecting
performance ............ A ............ Require replacement.
Splines worn close to
the end of their
useful life ............ 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
U-bolt damaged, affecting
performance ............ A . Require replacement of U-bolts.
Yoke damaged, affecting
performance ............ A .. Require repair or replacement.
\
\
\
\
\
\
\
DUST BOOTS
NOTE: Does not include CV boots.
DUST BOOT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Cracked, not leaking .... 1 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Page 474 of 1333
CLUTCH PEDAL POSITION SWITCHES
COLD START INJECTORS
CONNECTORS
COOLANT
COOLANT RECOVERY TANKS
COOLING FAN MOTOR MODULES
COOLING FAN MOTOR RELAYS AND MODULES
COOLING FAN MOTOR RESISTORS
COOLING FAN MOTOR SENSORS AND SWITCHES
COOLING FAN MOTOR SWITCHES
COOLING FAN MOTORS
CRANKSHAFT POSITION SENSORS
DECEL VALVES
DEFLECTORS
DIP STICKS AND TUBES
DIP STICK TUBES
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR CAPS
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ROTORS
DISTRIBUTOR SHIELDS
DISTRIBUTORS
EARLY FUEL EVAPORATION VALVES (HEAT RISER ASSEMBLIES)
EGR COOLERS
EGR EXHAUST MANIFOLD PASSAGES
EGR INTAKE AND EXHAUST MANIFOLD PASSAGES
EGR PLATES AND COOLERS
ELECTRONIC SPARK CONTROL MODULES
ELECTRONIC TRANSMISSION CONTROL DEVICES
ELECTRONIC TRANSMISSION FEEDBACK DEVICES
ENGINE COOLANT TEMPERATURE SENSORS
ENGINE COOLING SYSTEMS
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE OIL
ENGINE OIL CANISTERS
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL GASKETS
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER PURGE DEVICES
EVAPORATIVE EMISSION (EVAP) CANISTERS
EVAPORATIVE EMISSION (EVAP) FEEDBACK DEVICES
EXHAUST GAS RECIRCULATION DEVICES
EXHAUST GAS RECIRCULATION FEEDBACK DEVICES
EXPANSION PLUGS
FAN CONTROL SENSORS
FUEL
FUEL ACCUMULATORS AND DAMPERS
FUEL AND COLD START INJECTORS
FUEL DAMPERS
FUEL DELIVERY CHECK VALVES
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL FILLER NECKS AND RESTRICTORS
FUEL FILTERS
FUEL INJECTORS
FUEL LEVEL SENDERS7
FUEL PRESSURE REGULATORS
FUEL PUMPS (IN-TANK AND EXTERNAL, ELECTRICAL OR MECHANICAL)
FUEL RAILS
FUEL RESTRICTORS
Page 475 of 1333
FUEL TANKS
GAS CAPS
GASKETS
GROMMETS (VALVE COVER)
HARMONIC DAMPERS
HEATER CONTROL VALVES
HEATER CORES
HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS
HOSE CLAMPS
HOSE CONNECTORS
HOSE COUPLERS
HOSES AND TUBES (FUEL LINES, RADIATOR, VACUUM, BY PASS,
HEATER, RECOVERY TANK AND OIL COOLERS)
HOUSINGS
IDLE AIR CONTROLS
IDLE SPEED CONTROL ACTUATORS
IGNITION BOOTS
IGNITION COIL TOWERS
IGNITION COILS
IGNITION CONTROL MODULES (ICM)
IGNITION SWITCHES
IGNITION TERMINALS
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY)
IN-TANK FUEL STRAINERS
INERTIA FUEL SHUT-OFF SWITCHES
INTAKE AIR TEMPERATURE SENSORS
INTAKE MANIFOLDS
INTERCOOLERS
KNOCK SENSORS
LIQUID VAPOR SEPARATORS
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSORS
MASS AIR FLOW (MAF) SENSORS
METAL AIR MANIFOLDS AND PIPES
METAL AIR PIPES
MIX CONTROL SOLENOIDS
MOTOR MOUNTS
O-RINGS, GASKETS, SEALS AND SPRING LOCKS
O2 SENSORS
OIL PRESSURE SENDING UNITS
OIL PUMP PICK-UP SCREENS
OIL PUMPS
PARK NEUTRAL POSITION SWITCHES
PCV BREATHER ELEMENTS
PCV ORIFICES
PCV VALVES
PICK-UP ASSEMBLIES (INCLUDES MAGNETIC, HALL EFFECT AND
OPTICAL)
POWER STEERING PRESSURE SENSORS
POWERTRAIN CONTROL MODULES (PCM) AND PROM
POWERTRAIN CONTROL PROM
PRESSURIZED EXPANSION TANK CAPS
RADIATOR CAPS AND PRESSURIZED EXPANSION TANK CAPS
RADIATOR FAN BLADES
RADIATOR FAN CLUTCHES
RADIATORS
ROLL OVER VALVES
SEALING COMPOUNDS
SEALS
SECONDARY AIR INJECTION SYSTEM MANAGEMENT DEVICES
SENSORS AND ACTUATORS
SHROUDS, BAFFLES AND DEFLECTORS
SPARK PLUGS
SPRING LOCKS
Page 506 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TU](/manual-img/19/57332/w960_57332-505.png "MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TU")
\
\
\
\
\
\
\
DIP STICK TUBES
See DIP STICKS AND TUBES .
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ADVANCE AND RETARDER (MECHANICAL AND VACUUM) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A .. Require repair or replacement.
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A ............ Require replacement.
Out of specification .... B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR BOOT AND SHIELD INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Deteriorated ............ A ............ Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. A ............ Require replacement.
Torn .................... A ............ Require replacement.
\
\
\
\
\
\
\
DISTRIBUTOR CAPS
DISTRIBUTOR CAP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 508 of 1333
Eroded .................. 1 ............ Suggest replacement.
Loose ................... A .. Require repair or replacement.
Out of specification .... B ............ Require replacement.
\
\
\
\
\
\
\
DISTRIBUTOR SHIELDS
See DISTRIBUTOR BOOTS AND SHIELDS .
DISTRIBUTORS
DISTRIBUTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bushings worn, affecting
performance ............ A .. Require repair or replacement.
Bushings worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Cam lobes worn, affecting
performance ............ A .. Require repair or replacement.
Cam lobes worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Gear broken ............. A .. Require repair or replacement.
Gear worn, affecting
performance ............ A ............ Require replacement.
Gear worn, not affecting
performance ............ .. ........ No service suggested or
required.
Integrated pickup
triggering device
loose .................. A .. Require repair or replacement.
Integrated pickup
triggering device
magnetism incorrect .... A .. Require repair or replacement.
Leaking oil internally .. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Pickup triggering device
(reluctor) broken ...... A .. Require repair or replacement.
Pickup triggering device
(reluctor) loose ....... A .. Require repair or replacement.
Pickup triggering device
(reluctor) weak ........ A .. Require repair or replacement.
Reluctor (pickup
triggering device)
broken ................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
loose .................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
weak ................... A .. Require repair or replacement.
Shaft bent .............. A ............ Require replacement.
Thrust washer broken .... A .. Require repair or replacement.
Page 535 of 1333
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
IGNITION BOOTS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COIL TOWERS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COILS
IGNITION COIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or