Page 664 of 1216
Page 668 of 1216
19-20STEERING - Steering Wheel and Shaft
13AOWColumn tube Column
I18.5W.5 mm
Column tube(.73-.81 in.)13AO26015. APPLICATION OF GREASE TO
BEARING SPACERApply multipurpose grease to the surfaces of the bearing
spacer which contacts the steering shaft.
qGrease: MOPARMulti-mileage
LubricantPart .--.No. 2525035 or equivalent
12. INSTALLATION OF COLUMN TUBE CLAMP
(1) Slide the colum tube and adjust so that dimension A in
the figure is the standard value.
Standard value: 24.8-25.2 mm
(.98-.99 in.)(2) Install the column tube clamp at the position where
the dimension shown in the figure is obtained.
11. APPLICATION OF GREASE TO BEARING SPACER
Apply multipurpose grease to the surfaces of the bearing
spacer which contacts the steering shaft.
Grease: MOPARMulti-mileage
LubricantPart rr.No. 2525035 or equivalent
8. INSTALLATION OF STEERING
LOCK/7. STEERING -”LOCK BRACKET/G. STEERING LOCK INSTALLATION
SPECIAL BOLT(1) When installing the steering
lock- and steering lock
bracket to the column tube, temporarily install the
steering lock in alignment with the column boss.
(2) After checking that the lock works properly, tighten
the special bolts until the head twists off.
CautionThe steering lock bracket and blots must be re-
placed with new ones when the steering lock is
installed.4. INSTALLATION OF JOINT ASSEMBLY
/3. BEARING/
2. COVER ASSEMBLY
(1)
Install the cover assembly on the joint assembly.
(2) Fill the inside of the bearing with multipurpose grease.
Grease: MOPAR Multi-mileage Lubricant Part
No. 2525035 or equivalent
(3) Install the bearings to the shaft on the joint assembly.
(4) Wrap vinyl tape approximately one and one-half times
around the concave circumferences of the bearings,
and then press fit the bearings into the cover assem-
*
bly.(5) Apply multipurpose grease to the mating surfaces of
the joint and cover assemblies.
Grease: MOPAR Multi-mileage Lubricant
PartNo. 2525035 or equivalent
Page 676 of 1216
19-28STEERING - Power Steering Gear Box
POWER STEERING GEAR BOXREMOVAL AND INSTALLATION
-
NlSPA--
Pre-removal Operation@Draining of the Power Steering Fluid@Removal of Transfer:1&&r:, GROUP 21 -Transfer.)50-65 Nm36-47 ft.lbs.
I/a
Post-installation Operationl Installation of Transfer(:zD:” GROUP 21 -Transfer.)
l SSy,lying of the Power Steeringl Bleedino of the Power Steering
Fluid
Liie(Refer to P.19-13.1l khecking of Steering Wheel Posi-tion with Wheels Straight Ahead*Adjustment of the Front Wheel
Alignment
(Refer to GROUP Z-Service Ad-
justment Procedures.)
Removal steps1.
“,;;rt assembly and gear box connecting
bolt
2. Connection for return tube
3. Connection for pressure hose
4. Cotter pin
5.
Aft-cd end and knuckle connecting
4I)f3: H,“a:od end
8. Stabilizer bar bracket
9. Front roll stopper mounting bolt10. Center member rear mounting bolt
4411. Front exhaust pipe l * l + 12. Gear box assembly
l + 13. Mounting rubber
(I) Reverse the removal procedures to reinstall.(2) +e : Refer to “Service Points of Removal”.(3) .* : Refer to “Service Points of Installation”.(4) q : Non-reusable parts(4) lli
3oh2 Nm22-30 ftlba.^a-aa I.au-IUU NrnI
IO-15 Nm22-29
ft.lbs.
15-20 Nm15-20 Nm
11-14 ft.lbs.
13A027612-18 Nm
A-34 IUm
K-
1 j-+ft.lbs.
:II I-.5
/ .2!
i!!1
NOTEW-W Nm43-58
ft.lbs.13A0353
Page 704 of 1216
MANUAL TRANSAXLE - Specifications
ItemsNm
ftlbs.Reverse shift lever assembly attaching bolt
15-2211-15
Bearing retainer bolt15-2211-15
Differential drivegear
bolt
130-14094-101Interlock plate bolt
20-2715-19
Select lever assemblymountingbolt15-2211-15
LUBRICANTS
NZlCD-A
ItemsManual transaxle oil
Drive shaft oil seal lipSpecified lubricant
MOPAR Hypoid gear oil or equivalent
API classification GL-4 or higher
MOPAR Hypoid gear oil or equivalent
API classification GL-4 or higherQuantity lit. (qts.)
1.8 (1.9) 2.2 (2.3)’
As required
Shift lever bushingMOPAR Front Wheel Bearing Grease
Part No. 3837794 or equivalentAs required
SEALANTS AND ADHESIVES
NZlCE-A
IItemsSpecified sealants and adhesivesITransaxle case-clutch housing mating surfacesMitsubishi genuine Part No.
MD997740 or equivalent
Transaxle case-rear cover mating surfaces
Differential drive gear bolts
Bearing retainer screw (flush head screw)MOPAR Part
No.4318031 or MOPAR Part No.4318032or equivalent
Air breather
IMOPAR Part
No.4318025 or equivalent
Page 722 of 1216
21-28MANUAL TRANSAXLE - Transaxle Assemblv
seal
201025Apply
adhesive
(.2 in.)TFMOO63
60. INSTALLATION OF OIL SEALInstall the input shaft front oil seal using the special tool.
52. INSTALLATION OF INTERMEDIATE GEAR ASSEMBLY /
53. INPUT SHAFT ASSEMBLYLifting up the input shaft assembly, install it simultaneously
with the intermediate gear assembly.
49. APPLICATION OF ADHESIVE TO BOLTApply specified adhesive to the bolt threads.
CautionDo not apply to the bolt head.
Specified adhesive: MOPAR Part No.4318031or MOPAR Part
No.4318032
or equivalent
Page 732 of 1216
21-38 MANUAL TRANSAXLE - Transaxle Assembly
63. INSTALLATION OF OIL SEALInstall the input shaft front oil seal using the special tool.
,,=
2010041
51. APPLICATION OF ADHESIVE TO BOLTApply specified adhesive to the bolt threads.
CautionDo not apply to the bolt head.
Specified adhesive: MOPAR Part No.4318031or MOPAR Part
No.4318032
or equivalent
50. INSTALLATION OF SHIFT RAIL ASSEMBLY
(1) Set the lst-2nd speed shift sleeve at 2nd speed.
(2) Set the
3rd-4th speed shift sleeve at 4th speed.
(3) FJtt~~~shift forks of shift rail assembly to groove of
(4)
Insert the shift rails into the shift rail holes of clutch
housing.(5) Turn the shift rails in the directions indicated by the
arrows in the order shown in the illustration, and
engage the shift lugs to control finger and interlock
plate.A
Page 734 of 1216
21-40 MANUAL TRANSAXLE - Transaxle Assembly Amount
1-2 mm
J
33. INSTALLATION OF OIL SEALInstall the drive shaft oil seal using the special tool.
.‘p,
/
27. INSTALLATION OF OIL GUIDEInstall the oil guide to the transaxle case as illustrated.
26. INSTALLATION OF TRANSAXLE CASE(1) Place the selected spacers on the intermediate gear
and the differential’s bearing outer race. Also insert the
selected spacer between the output shaft bearing outerrace and the transaxle case.
(2) Set so that the threaded hole of the reverse idler gear
hshaft’s head is facing in the direction indicated in the
.-
illustration.
NOTEIf there is a great deviation in the direction in which the
threaded hole is facing, it will be impossible to align thethreaded hole and the hole in the case after the
transaxle case is installed.
(3) Apply specified sealant to the clutch housing side of the
transaxle case.
Specified sealant: MITSUBISHI Genuine
Part No.
MD997740
or equivalent
Caution
Squeeze out sealant from the tube uniformly with-
out excess or discontinuity.(4) Install the transaxle case onto the clutch housing.
(5) Insert a Phillips screwdriver
18 mm (32 in.) shaft
diameter] into the bolt hole in the case, as shown in thefigure, and use it to align the threaded hole of the
reverse idler gear shaft with the bolt hole in the
transaxle case.(6) Install the reverse idler gear shaft bolt and tighten the
bolt by fingers.
(7) Tighten the all transaxle tightening bolts to specified
*
torque.,-(8) Tighten the reverse idler gear shaft bolt to specified
torque.
Page 770 of 1216
21-76MANUAL TRANSAXLE -Specifications/Special Tools
SEALANTS AND ADHESIVESNZlCE-B
TransaxleH-
1
-/Items
Transaxle case-clutch housing mating surfaces
Transaxle case-adapter mating surfaces
Adapter-rear cover mating surfaces
Front differential drive gear bolts
Center differential drive gear bolts
Bearing retainer screw (flush head screw)
Reverse brake cone mounting screw bolts
Air breatherSpecified sealants and adhesives
Mitsubishi genuine part
No.997740or equivalent
MOPAR part
No.4318031 or MOPAR part
No. 4318032 or equivalent
MOPAR part
No.4318025 or equivalent
TransferItems
Adapter-extension housing mating surfacesSpecified sealants and adhesives
Mitsubishi genuine part No.
MD997740or equivalent
Air breatherMOPAR part
No.4318025 or equivalent
SPECIAL TOOLSNZlDA-B AI
NllmherName
I Use,“I. .-. * ,--.
~ MD99801 9
.-...-Lock pin extractor---Removal of spring pin and lock pin
MD998245Lock pin installerInstallation of spring pin and lock pin
0
MD998304Oil seal installerInstallation of front output shaft bearing and
transfer extention housing oil seal
MD998320Bearing installer
Installation of input shaft bearing and input
shaft gear
