1991 MITSUBISHI ECLIPSE window

23-48
MOULDINGBODY
- Moulding
REMOVAL AND INSTALLATION67 6WA0421
4,1. Drip moulding4,2. Windshield upper moulding
l *3. Quarter window moulding lower
**4. Quarter window moulding upper
4*5. Quarter window moulding front
l *6. Liftgate moulding lower
l +7. Liftgate moulding uppera*8. Liftgate moulding side
+* l + 9. Side protect moulding fender
+e I)+ 10. Side protect moulding front door
4,11. Side protect moulding quarter
NOTE(1) ** : Refer to “Service Points of Removal”.(2) I)+ : Refer to “Service Points of Installation”.
SERVICE POINTS OF REMOVAL1. REMOVAL OF DRIP MOULDING
Refer to
P.23-72.2. REMOVAL OF WINDSHIELD UPPER
MOULDINGRefer to
P.23-58.

BODY - Moulding23-493.
REMOVAL OF QUARTER WINDOW MOULDING LOWER/
4. QUARTER WINDOW MOULDING UPPER/B. QUARTERWINDOW MOULDING FRONT
Refer to
P.23-61.6. REMOVAL OF
LIFTGATE MOULDING LOWERI7. LIFT-GATE MOULDING
UPPER/8. LIFTGATE MOULDING
SIDERefer to
P.23-62.
19. REMOVAL OF SIDE PROTECT MOULDING
FENDER/IO.SIDE PROTECT MOULDING FRONT DOOR
(1) Using the plastic trim tool, pry off the side protect
moulding.
(2) Using the plastic trim tool, scale off the both-side
adhesive tape which sticks to the body.
11. REMOVAL OF SIDE PROTECT MOULDING QUARTER
(1) Remove the rear side trim. (Refer to P.23-85.)(2) Remove the motor section of the driving device
assembly. (Refer to
P.23-94.)(3) After removing the mounting nuts, pry off the side
protect moulding quarter with the plastic trim remover.
SERVICE POINTS OF INSTALLATION9. INSTALLATION OF SIDE PROTECT MOULDING FEN-
DER/10. SIDE PROTECT MOULDING FRONT DOOR
(1) Wipe off application surface of body with clean cloth
dampened with degreaser
(MOPAR SUPER KLEEN or
equivalent).
NOTEAfter wiping surface, leave surface as it is to volatilize
degreaser.(2) Using an infrared light or similar instrument, heat the
body painted surface and the side protect moulding.
Heating temperature
Body painted surface..... 25-55OC (77-131 OF)
Side protect moulding . . . . 25-40°C (77- 104OF)

23-54BODY - Window Glass
WINDOW GLASS
N23LAAB
GENERALThe windshield and
liftgate window glass are attached by an urethane-base adhesive to the window frame.
This adhesive not only provides improved glass holding and sealing, but also permits use of body openings
having a greater
structural strength.
ADHESIVE, PRIMER AND RESERVE ITEMSItems
ApplicationsQuantityAdhesive, Primer
Adhesive:As required
3M Super Fast Urethan Part No.8609
or equivalent
Primer:As required
3M Super Fast Urethan Primer
Part
No.8608 or equivalentReserve items
Dispensing nozzleOne
Wire (dia. x length)for cutting adhesiveLir,“$c;s onfi wire(62 in.
x 3.3 ft.)
Adhesive gunfor adhesive application
OneIsopropyl alcoholfor cleaning jointing surfacesAs required
Wiping ragsAs required
Sealerfor prevention of water leaks andAs requiredgathering after adhesive applicationIsopropyl alcoholfor cleaning
As requiredGlass holderTwo
Spacers (Service Part)As required
Window moulding assembly
One(Service part)
Tectyl 506T (Valvoline Oil Company)As required

BODY - Window Glass23-55
WINDSHIELD INSTALLATION PROCEDURE
_-Body
--
+
e-eRemoval of moulding
(Wire)
IFinishing of adhesive
surfaceGlass-tIf reusing glass;
r --------- 1 ---s------ - -‘-,
IRemoval of adhesive and dam rL---------r---s---------- I
e-e _---mm,- __-_--_ 1,(Paint thinner)
II
IIIship ofglass tobody
IApplication of solvent
(Isopropyl alcohol)
III
-*I(Isopropyl alcohol)
(glass blackout primer)
pi&g(urethane adhesive)
-1 I- - -Installation of glass
_to body
ICleaning of attaching
surface
1If water leaks
--------------~
p%zG&pJ(Isopropyl alcohol)

23-56BODY - Window Glass
Recommended tool
Make the toolby
Windshield glass
Roof panel
scoop out
this portion.
iiiii- ,.:::i:::::::::::i.p:://jiiiig;iiiijjiiij
I&
::::::::::iiiiiii.::;QuarterQuarter
panelwindow
glass
WA0870Windshield
uppermoulding
Primer
Quarter
window
moulding
front---
---. Cuthere.
4%
>/yere.
MAO672-
REPLACEMENT OF MOULDING (WINDSHIELDUPPER
MOULDING AND QUARTER WINDOW p;MOULDING FRONT)
N22LABc -1. Remove the mouldings. (Refer to
P.23-58, 61.)
2.To cut the existing adhesive, make a tool such as the one
shown.3. Using the tool, scoop out the existing adhesive.
Caution
Take care not to remove more adhesive than neces-
sary, and not to scratch the glass or body.
4.Cut away part of the new moulding and provisionally attachthe moulding. Check to be sure that it fits closely to the
surface.
5.A coating of the specified primer should be applied to the
moulding.
Specified primer:
3M Super Fast Urethan Primer Part
No. 8808 or equivalent
Caution
Do not touch the surfaces that are coated with primer.

BODY - Window Glass23-57Windshield
uppermoulding
Additional
Quarter window
moulding front6. Apply a coating of the specified adhesive where shown in
the illustration, and then install the moulding before the
adhesive hardens.
Specified adhesive: 3M Super Fast Urethan PartNo. 8609 or equivalent
7. Scrape away excessive sealant forced out during installa-
tion of the moulding from the glass or body and wipe the
surfaces clean with MOPAR SUPER KLEEN or equivalent.8. After completion of installation, leave the moulding undis-
turbed until the adhesive hardens.
-.

BODY - Quarter Window Glass23-61QUARTER WINDOW GLASS
N22LEAKPre-removal Operation
@Removal of Rear Side Trim, Quarter
Trim. Center Pillar Trim and Rear
IPillar’ Trim
I(Refer to
P.23-85.)l kemoval of Side Air SpoilerI(Refer to
P.23-74.)Iter Trim, Center Pillar Trim and Rear
Removal steps1. Quarter window moulding lower
2. Quarter window moulding upper
3. Quarter window moulding front
4. Quarter window glass
5. Quarter window moulding clipInstallation steps5. Quarter window moulding clip
l + 3. Quarter window moulding front
l * 4. Quarter window glass
2. Quarter window moulding upper1. Quarter window moulding lower
NOTE(1) l + : Refer to “Service Points of Installation”.(2) $ : Non-reusable parts
Quarter window glass
SECT.B-B and C-C
SECT. A-A
18AO521mm
(in.)18AO521
-ISERVICE POINTS OF INSTALLATION3. INSTALLATION OF QUARTER WINDOW
MOULDING
FRONT/4. QUARTER WINDOW GLASS
(1) Remove residual-sealant from the body and glass.
(2) Degrease the body and glass, and coat primer.
(Refer to
P.23-59.)
(3) Coat specified sealant on the indicated position of the
glass.Specified sealant: MOPAR Silicone Rubber Sealer
Part No.4626070 or Auto Glass
Adhesive and Sealer PartNo.2298825 or equivalent
(4) Mount the glass on the body.

23-62BODY - Liftgate Window Glass
LIFTGATE WINDOW GLASSN22LDAK
REMOVAL AND INSTALLATION
Pre-removal Operation*Removal of Liftgate Trim and Flange
Trim
(Refer to
P.23-86.)aRemoval of Air Spoiler
(Refer to P.23-74.)Post-installation Operation
*Installation of Air Spoiler
(Refer to
P.23-74.)*Installation of Liftgate Trim and
Flange Trim
(Refer to
P.23-86.)
I
Removal steps
I. Liftgate moulding upper
2. Liftgate moulding clip
3. Liftgate moulding lower
4. Liftgate moulding side
o*5. Liftgate window glass
6. Liftgate moulding fastener
7.
Liftgate moulding clip
Installation steps7.
Liftgate moulding clip
6.
Liftgate moulding fastener
M 4. Liftgate moulding side
w 5. Liftgate window glass
3.
Liftgate moulding lower
2. Liftgate moulding clip1. Liftgate moulding upper
WA0487NOTE
(1) l * : Refer to “Service Points of Removal”.(2) .+ : Refer to “Service Points of Installation”.(3) q : Non-reusable parts
SECT. A-A
SECT. B-B(Other areas not illustrated arethe same as those in cmss sec-
SECT. C-C(Other areas not illustrated are thesame as those ,ncrms sectmn A-A )1ar40525mm
(in.)
ISA0526
SERVICE POINTS OF REMOVAL5. REMOVAL OF
LIFTGATE WINDOW GLASS
Remove the quarter window glass in the same procedure as
the windshield glass. (Refer to
P.23-58.)
SERVICE POINTS OF INSTALLATION4. INSTALLATION OF
LIFTGATE WINDOW MOULDINGSIDE/5.
LIFTGATE WINDOW GLASS
Compared with the windshield glass, adhesive is coated onthe different position but the working procedure is same.
(Refer to
P.23-59.)