1991 MITSUBISHI 3000GT relay

14-10COOLING - Radiator
r-----I
113
EY
4 :
2 :
i.-.-..i
0312161908
Ionnector04FOOO8
RADIATOR FAN MOTOR RELAY INSPECTION
(1) Remove radiator fan motor relay from the relay box located
at the right side in the engine compartment.
Ll(2) Check for continuity between the terminals when the
battery power-supply is applied to terminal
0, and terminal@ is grounded.
When current
flowsBetweenterminals 1
- 3Continuity
When nocurrent flowsBetweenterminals 1 - 3No continuity
Betweenterminals 2 - 4Continuity
SERVICE POINT OF INSTALLATIONM14QDAH
11. CONNECTION OF RADIATOR FAN MOTOR CONNEC-
TORConnect the radiator fan motor connector to the body
harness. Then, insert into the shroud hole and fix securely.
TSB Revision

15-4INTAKE AND EXHAUST -Troubleshooting (Active Exhaust System)
TROUBLESHOOTING (ACTIVE EXHAUST SYSTEM)MlSEBAA
TROUBLESHOOTING PROCEDURE(1) Make sure that the valve operating cable is not dislocated.
(2) Make sure that the connectors of each component are positively connected and that no fuse has blown.
(3) Have an overall understanding of the substance and procedure of checking by reference to the
Troubleshooting Quick-Reference Table and perform check in the proper sequence.
(4) Check each component with its connectors disconnected.
TROUBLESHOOTING QUICK-REFERENCE TABLEIf no abnormality is found in all parts by the check performed in the following sequence, the problem is
probably caused by faulty active exhaust control unit and therefore the active exhaust control unit is replaced.
Se-Part to becheckedCheckingprocedureJudgement
Probable causeluenceRemedy
Normal
Abnormal
1ValveOperate valve
manually.Operates freely.Does not operate.Valve stickingReplace mainmuffler.
2ActiveRefer to P.15-34.exhaustFaulty switchReplace switch.
switch
3PowerwindowCheck continuity
between terminalsContinuity presentNo continuity
Faulty power
relay
@and @of
relay.window relayReplace power
window relay.
With battery voltage
applied between
terminals @and
@of relay, check
continuity between
terminals
@ and @of relay.
4
Actuator
Check contrnuityassembly
between terminalsNO continuity present
between terminalsContinuity present
between terminals
in SPORT mode.@and 0.@and 0.
Continuity present
between terminalsNo continuity present
between terminals
@and
0.@and 0.
Check continuity
between terminalsContinuity present
between terminalsNO continuity presentbetween terminalsFaulty actuator
Replace actuator
while idling in
@and 0.@and @assemblyassembly.
TOUR mode.NO continuity present
between terminalsContinuity present
between terminals
@and
0.@and 0.
Apply battery
Motor operates.Motor does not
voltage between
terminals @andoperate.
0.Motor turns inMotor does not
reverse directionturn.when polarity is
reversed.
5CableOperate activeBroken orexhaust switchActuator operates
and valve operatesActuator operates,
but valve doesReplace or adjust
(while idling)
as well.not work.maladjusted cable cable
TSB Revision

17-8EMISSION CONTROL - Evaporative Emission Control System
PURGE CONTROL SYSTEM INSPECTION M17IBBQ
Canister
Purge control
valve\
PI IrnQ rnntrnlI.1 I
kXffo~~~~r~~ ’ I I-J
relay
Barometric pressure sensor
Intake air temperature sensor
Engine coolant temperature sensor
II1 I IAir flow sensor
Engine control unit
6EM0215(1) Disconnect the purge air hose from the air intake hose, and
plug the air intake hose. Then, connect the hand vacuum
pump to the purge air hose.
(2) Under the engine conditions shown below, check by
applying vacuum from a hand vacuum pump.
When engine is cold
-engine coolant temperature:
60°C (140°F) or less
Engine operating
conditionApplying vacuumResult
Idling
375 mmHgVacuum is maintained
3,000 rpm(14.8 in.Hg)When engine is hot
-engine coolant temperature:
70°C (158°F) or higher
Engine operating
condition
Idling
3,000 rpm within
three minutes after
starting engine
3,000 rpm after
three minutes
have elapsedafter startingengine
Applying vacuum
375
mmHg(14.8 in.Hg)
Try applyingvacuum
375
mmHg(14.8 in.Hg)
Result
Vacuum is marntained
Vacuum leaks
Vacuum WIII be main-tained momentarily, after
which it will leak.
NOTEThe vacuum WIII leak con-
tinuously if the altitude
is 2,200 m
(7,200 ft.) orhrgher. or the Intake arrtemperature is 50°C(122°F) or higher.
1 TSB Revision

23-30AUTOMATIC TRANSAXLE - Troubleshooting
TRANSMISSION CONTROL UNIT
The connector has 42 pins to accommodate the increased number of senso.r inputs.
Here are the pin assignments.
uu
101.102.103.
104.105.
106.
107.
108.
109.
110.
1.
3':4.
Z:
i:9.10.11.
12.
13.
14.
15.
16.
17.
18.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.Damper clutch control solenoid valve
Shift control solenoid valve A
-Power source
Ground
Pressure control solenoid valve
Shift control solenoid valve B
. .
*Engine communrcatron srgnaiPower source
Ground
Ground
-Accelerator switch
-Diagnosis output terminal
Air-conditioner relay signal
Engine communication signal
Diagnosis control terminal
Engine communication signal
Power source (backup)Kickdown servo switch
Idle switch
oil temperature sensor (Low temperature side)
Oil temperature sensor (High temperature side)
Throttle position sensor
Sensor ground
Vehicle-speed reed switch
Inhibitor switch
(P)Inhibitor switch (R)Inhibitor switch (N)Inhibitor switch (D)
Inhibitor switch (2)
Inhibitor switch
(L)Overdrive switch
Pulse generator B
Pulse generator B
Pulse generator A
Pulse generator A
Ground
Ignition pulse
Power mode signal
TFA0360
TSB Revision

AUTOMATIC TRANSAXLE - Troubleshootinn23-43
CONVERTER STALL TESTStall test consist of determining maximum engine
speed obtained at full throttle in “D” and
“I?”positions. This test checks torque converter
statoroverrunning clutch operation, and holding ability of
transaxle clutches and low-reverse brake.
Caution
During this test, make sure that no one stand in
front of or behind vehicle.
1. Check transaxle fluid level. Fluid should be at
normal operating temperature
[70 - 80°C (160 -
18O”F)I. Engine coolant should also be at normal
operating temperature
[80 - 90°C (180 - 19O”F)l.2. Apply chocks to both rear wheels.
3. Attach engine tachometer.
4. Apply parking and service brakes fully.
5. Start engine.
6. With selector lever in “D” position, depress
accelerator pedal fully to read engine maximum
rpm. Do not hold throttle wide open any longer
than is necessary to obtain maximum engine
rpm reading, and never longer than 5 seconds at
a time. If more than one stall test is required,
operate engine at approximately 1,000 rpm in
neutral for 2 minutes to cool transaxle fluid
between tests.
Stall speed: 2,200
- 3,200 rpm
7.Place selector lever to “R” position and perform
stall test by the same procedure as in foregoing
item.
Stall Speed Above Specification in “D”
If stall speed is higher than specification, rear clutch
or overrunning clutch of transaxle is slipping. In this
case, perform hydraulic test to locate cause of
slippage.
Stall Speed Above Specification in “R”
If stall speed is higher than specification, front
clutch of transaxle or low-reverse brake is slipping.
In this case, perform hydraulic test to locate cause
of slippage.
Stall Speed Below Specification in “D” and “R”
If stall speed is lower than specification, insufficient
engine output or faulty torque converter is sus-
pected. Check for engine misfiring, ignition timing,
valve clearance, etc. If these are good, torque
converter is faulty.
TRANSAXLE CONTROL
Symptom
Selector lever operationis stiff
Probable cause
Incorrect adjustment of sleeve
Remedy
Adjust
Incorrect adjustment of control cable
Excessive wear of detent plate
Worn contact surfaces of pushbutton
and sleeve
Adjust
Replace
Replace
Starter motor does notMalfunction in inhibitor switchReplace
operate with the selector
lever in the “N” or “P”Incorrect adjustment of control cableAdjust
position
Will not shift to
4-speed
Malfunction of starter relay
Malfunction of OD switchReplace
Replace
1 TSB RevisionI

33B-22 ELECTRONIC CONTROL SUSPENSION (ECS) - Circuit Diagram
CIRCUIT DIAGRAMM33ZEAB
TAILL-_
-
!
!-1
J/G
pyspq3 2 10’1? 12!~3 Ir. Eli
,lGH-.-
3&
Eiv,I
1 \L-2
E
s=
43
21_r
%c;
0
,-:=
J.4
T RELAY--
-1 F;;;CATED
-
1234
-m5578
__p7zERmj
FUSIBLE LINK@J/B
@
I 81GAI
ELECTROMIC CONTROLSUSPEldSiOi,dCONTRllL Ui'dIT
----- -m12123E>[1:
II
1u2m
II
JUIvPERBCONNECTOR
LEd1254
m
M
,p 10___. _
lt f“u 1
0, iLL
1-L. ET- JN
i;4 m'llm
i I
ECSSWITCr;
pg&-jqq-.
E
t2
12’
II334
%
-
rk
8
62-------____
-
q
ET
12---c.
n
G
3-
I
.---._-__60
1------.--
Q2A
10-
SELF-DIAGNOSISCXECK COKNECTOR
X35-AX-Bi?Gl-E,TSB Revision

L,
SERVICE
BRAKES
CONTENTSM35AA..
ANTI-LOCK BRAKING SYSTEM TROUBLESHOOTING7Actuator Test Function
. . . . ..___..._____.__................................ I 2, 36Check Using Self Diagnosis Function __._.....,_._.._____........ 11, 28
Diagnosis Code Chart ..,,........,......_..................................,. 1 I, 28
How to Use the Troubleshooting Flow Chart
_____.___......._._.7Method of Clearing Diagnosis Code Memory._.,._...... 12, 30
Particular Phenomena of the Anti-lock Braking System
7Troubleshooting (ABS-AWD) ._______._.._...........................,... 26
Troubleshooting (ABS-FWD) ______.._._........_...........,.....,.....,....8
TroubleshootingMethods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
BRAKE LINE . . . . . . .._.......................................................................71
BRAKEPEDAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
ELECTRONIC CONTROL UNIT (ABS). . . . .._._..___..__._............93/
L
FRONT DISC BRAKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73G SENSOR (AWD-ABS)’
____.____.___.__._._.................,,......,.....,.... 92
HYDRAULIC UNIT (ABS) .___.._._._._.______.............,...,,..........~ .,_____86
MASTER CYLINDER AND BRAKE BOOSTER ..__.._____.._____67SPECIFICATIONS ._....._.___.....................................
REAR DISC BRAKE . . . . . . .._..._._.___................................................81
SERVICE ADJUSTMENT PROCEDURES..___........45Bleeding48
Brake Booster Operating Inspection.
46
Brake Drum Inside Diameter Check. . .56
BrakeFluidLevelSensor Check.46
Brake Lining and Brake Drum Connection Check56Brake
Linrng Thickness Check............................................Brake Pedal Inspection and Adjustment............................Check Valve Operation Check............................................Front Brake Disc Run-out Check........................................Front Brake Disc Run-out Correction................................Front Disc Brake Pad Check and Replacement................Inspection of Front Brake Disc Thickness........................Inspection of Hydraulic Unit................................................Inspectton of Power Relay....................................................Inspection of Valve Relay and Motor Relay (ABS)............Measurement of Wheel Speed Sensor Output Voltage
Proportioning Valve Function Test
....................................Rear Brake Disc Run-out Check........................................Rear Brake Disc Run-out Correction................................Rear Brake Disc Thickness Check....................................Rear Disc Brake Pad Check and Replacement................Remedy in Case of DischargedBattery............................56
45
46
52
53
48
5258
62
62
57
47
55
55
55
53
62
SPECIAL TOOLS ..__.......___..........................................................General Specifications
........................................................Lubricants............................................................................Sealants and Adhesives........................................................Service Specifications........................................................3
TROUBLESHOOTING............................................................5
WHEEL SPEED SENSOR (ABS)............................................88
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at anauthorized MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.
i

35-8SERVICE BRAKES -Anti-lock Braking System Troubleshooting
TROUBLESHOOTING (ABS - FWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
(2) With the ignition key in the “START” position,
below up to the time the engine starts?power to the ABS ECU is interrupted and the
(1) When the ignition key is turned to the “ON”ABS warning light remains lit because the valve
position, the ABS ECU causes the ABS warningrelay is OFF.
light to flash twice in about one second (during
(3) When the ignition key is returned from the
which the valve relay self check is made) and“START” position to the “ON” position, the
then causes it to go out.ABS warning light flashes twice in about one
second (during which. the valve relay self check
-is made again) and then goes out.
ABS warning
ONlightII
-I
keyACC,
LO!: +--14A0589
Yes>CONTINUED ON NEXT PAGE
No
”
weenABS warning
1 TSB Revision