1991 MITSUBISHI 3000GT brake rotor

SERVICE BRAKES - Wheel Speed Sensor (ABS)
IFrontRear

+ : Pole piece14N016:14NOlO:
SERVICE POINTS OF REMOVALM35OBAC
1.REMOVAL OF FRONT ROTOR / 5. REMOVAL OF REAR
ROTOR
CautiondDo not damage rotor teeth and never drop the rotor.
If the rotor has missing teeth or is deformed, accuratewheel speed detection cannot be expected and the
system may fail to function normally.
Use particular care in handling the front rotor of an
AWD vehicle as it cannot be disassembled.
3.REMOVAL OF FRONT SPEED SENSOR / 8. REAR SPEED
SENSOR
Caution
When removing the speed sensor from the knuckle, usecare not to strike the tip of the pole piece against the
rotor teeth or any other parts.
INSPECTIONMJSOCAC
INSPECTION OF SPEED SENSOR(1) Check the tip of the speed sensor pole piece for deposits of
metal or other foreign matter and clean the pole piece as
necessary.
Also check the pole piece for damage and replace if
damaged.d
Caution
The speed sensor pole piece is magnetized by a built-in
magnet inside the sensor, so it tends to attract metal.If the pole piece is damaged, accurate wheel speed
detection may not be expected.
(2) Measure resistance between speed sensor terminals.
Standard value:
Front
Rear
1.4-2.2
kR1.3-2.1
kR
0.8- 1.2 kfl
If the internal resistance of the speed sensor is out of
specification, replace with a new one.

SERVICE BRAKES - Wheel SDeed Sensor lABSI35-91
/
i
lARnlA6
14N012‘
3
(3) zue$ the speed sensor cable for open circuit and replace if
NOTERemove the cable clamp from the body and, while flexing
the cable near the clamp, check for temporary open circuit.
Also check connector connection and terminal insertion.
INSPECTION OF ROTORCheck the rotor for missing or worn teeth and replace if faulty.
SERVICE POINTS OF INSTALLATIONM350DAC8. INSTALLATION OF REAR SPEED SENSOR
Insert a feeler gauge between the speed sensor pole piece
and the rotor tooth surface and tighten the speed sensor to
specified torque where the clearance is as specified all
around.Standard value: 0.2
- 0.7 mm (.008 - .028 in.)
NOTEThe rear speed sensor pole piece-to-rotor tooth surface
clearance is not adjustable in the case of AWD vehicles. In
this case, measure the sensor mounting surface-to-rotor
tooth surface clearance.
Standard value: 28.15
- 28.45 mm (1.11 - 1.12 in.)
4. INSTALLATION OF FRONT SPEED SENSOR BRACKET
NOTE
(I) The right and left speed sensor brackets differ in shape.
Install correctly referring to the identification symbols.
FR: For front speed sensor
R:For right wheel
L:For left wheel
(2) After installation of the speed sensor to the bracket,
check that the letters “FR” are visible.
3. INSTALLATION OF FRONT SPEED SENSOR
Caution
Handle the speed sensor carefully so as not to strike the
tip of the pole piece or the rotor teeth against any metalparts and damage them.
Insert a feeler gauge between the speed sensor pole piece
and rotor tooth surface and tighten the speed sensor to
specified torque where the clearance is as specified all
around.Standard value: 0.3
- 0.9 mm (.012 - .035 in.)
TSB Revision

36-2PARKING BRAKES - Specifications
SPECIFICATIONSM36CA- -
GENERAL SPECIFICATIONS
ItemsSpecifications
iI”
Parking brakes
Type
Brake lever type
Cable arrangementMechanical brake acting on rear wheels
Lever type
V-type
SERVICE SPECIFICATIONSM36cB-.
Items
Standard value
Parking brake lever stroke
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Clearance between th;$;;d) sensor pole pieceand the rotor tooth
Limit
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Specifications
3 - 5 notches2.8
(.I 1)
168.0 (6.6)0.2
- 0.7 LOO8 - .028)
1 .o f.039)
169.0 (6.7)
LUBRICANTSM36CD- -
ditems
Rear brake shoe and backing plate contact surfaces
Contact surface between shoe & lining assembly’sstrut and adjusterSpecified lubricant
Brake grease SAE J310, NLGI No. 1
Contact surface between shoe & lining assembly and
shoe-adjustment bolt and shoe-support piece
SEALANTS AND ADHESIVES
ItemsSpecified sealant
Shoe hold-down pin installation surface3M ATD Part No. 8513 or equivalent
1 TSB Revision

36-10PARKING BRAKES - Parking Brake
SERVICE POINTS OF REMOVALM36YBALI. REMOVAL OF REAR SPEED SENSOR
Caution
When removing the speed sensor from the knuckle, usei&J 1
care not to hit the pole piece at its tip against the rotorteeth or other parts.
11 FO03814LOOOi
14NOli9. REMOVAL OF SELF-LOCKING NUT
With the special tool, secure the axle shaft and remove the
companion flange self-locking nut.
II. REMOVAL OF AXLE SHAFT ASSEMBLY
With the special tool, remove the axle shaft from the trailing
arm.
INSPECTIONM36YCAI
CHECKING FOR UNUSUAL WEAR OF THE BRAKE LININGAND BRAKE DRUM
(1) Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm
(.I10 in.)
Limit:
1.0 mm (.039 in.)
Caution
Replace the brake shoes if the thickness of the brakelining is the limit value or less.
(2)Measure the brake disc drum inner diameter at two or more
places.Standard value: 168.0 mm (6.6 in.)
Limit: 169.0 mm (6.7 in.)
CautionReplace if the brake disc drum inner diameter is the
limit value or more.
TSB Revision

PARKING BRAKES - Parking Brake36-11
14N000'
Spindle,
I’_14NOO05
SERVICE POINTS OF INSTALLATIONM36YDAP
17. INSTALLATION OF SHOE-TO-ANCHOR SPRINGThe shoe-to-anchor spring must be installed in the se-
quence shown in the illustration.
Caution
Each shoe-to-anchor spring has a unique spring loadand the spring “a”is painted to prevent erroneous
installation.
NOTEThe figure shows the left wheel; for the right wheel, the
position in symmetrical.
16. INSTALLATION OF ADJUSTERInstall the adjuster facing the left adjusting bolt to the
vehicle front and right adjusting bolt to the vehicle rear.
9. INSTALLATION OF SELF-LOCKING NUT
With the special tool, secure the axle shaft and tighten the
companion flange self-locking nut.
6. INSTALLATION OF FLANGE NUT
After tightening the flange nut, align with the spindle’s
indentation and crimp.
1. INSTALLATION OF REAR SPEED SENSOR
Insert a filler gauge between the speed sensor pole piece
and rotor teeth and tighten the speed sensor at such
position where the gap is as specified below over the entire
circumference.
Standard value: 0.2
- 0.7 mm (.008 - .028 in.)
TSB Revision