1991 MITSUBISHI 3000GT fuel

FUEL SYSTEM- Fuel Line and Vapor Line13451FUEL
LINE AND VAPOR LINEMlBKA-~
iREMOVAL AND INSTALLATION
i30 Nm
6

Removal steps
1, Reserve tank2. Battery
3. Battery tray with washer tank assembly
4. Purge control valve
M 5. Fuelvapor hose6. Canister
7. Vapor pipe assembly
l +8. Fuel return hosea*9. Eye bolt10. Gasket11. High pressure fuel pipel a 12. Fuel filter*I,13. Eye bolt
14. Gasket
l * 15. High pressure fuel hose
16. O-ring
w 17. Fuel vapor hose
18. Stone protector
19. Fuel vapor pipe20. Fuel return pipe
21. Fuel main pipe
Deli\rerye
i603N0012
1 TSB Revision

13-152FUEL SYSTEM- Fuel Line and Vapor Line
03FOO3
05FOO735 Nm7r; ft
Ihr-k” ._..I_.
@dFlare nut,xSERVICE POINTS OF REMOVAL
MlBKBAQ9. 13. REMOVAL OF EYE BOLT
Remove the eye bolt while holding the fuel filter nut
\securely.
Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
INSPECTION
MIBKCAJ
lCheck the hoses and pipes for cracks, bend, deformation
and clogging.
l Check the canister for clogging.
l Check the fuel filter for clogging and damage.
SERVICE POINTS OF INSTALLATION
MlSKDAU17.5. INSTALLATION OF FUEL VAPOR HOSE
/ 8. FUEL
RETURN HOSE
(1) If the fuel pipe has a stepped part, connect the fuel
hose to the pipe securely, up to the stepped part, as
shown in the illustration.
Iti(2) If the fuel pipe does not have a stepped part, connect
the fuel hose to the pipe securely, so that it is the
standard value.
Standard value: 25
- 30 mm (1.0 - 1.2 in.)
15. INSTALLATION OF HIGH PRESSURE FUEL HOSEApply engine oil to the hose union.
Insert the hose, being careful not to damage the O-ring, and
tighten securely.
CautionBecause there is high pressure applied between the
fuel pump and the injection mixer, be especially sure
that there is no fuel leakage in this area.
12. INSTALLATION OF FUEL FILTER(1) When installing the fuel filter, first temporarily install the
filter to the filter bracket; then insert the main pipe at
the connector part of the high pressure fuel pipe, and
manually screw in the main pipe’s flare nut.
(2) Holding the fuel filter nut, tighten the fuel main pipe’s
flare nut and eye bolt at the specified torque. Then
tighten the filter to the bracket.
TSB Revision1
‘d

FUEL SYSTEM - Fuel Filter13453
FUEL FILTERM13VA-.
/REMOVAL AND INSTALLATION
i&J
L
/Il Removal of Residual Pressure from
Post-installation Operation
l Checking for Fuel Leakage
Removal steps
1. Battery
2. Battery tray with washer tank assembly
3. Eye bolt4. Gasket
5. High pressure fuel hose
6. Connection of fuel main
pipe7. Mounting boltl *8. Fuel filterl *9. Eye bolt10. Gasket11. High pressure fuel pipe
l---
222 ft.lbs.03FOO12
Gasket
fuel pipe
&----Eye bo’t 03FOO13SERVICE POINTS OF REMOVAL
MlSVBAB3. 9. REMOVAL OF EYE BOLT
Remove the eye bolt while holding the fuel filter nut
securely.
Caution
Cover the hose connection with
rags to prevent splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
SERVICE POINT OF INSTALLATION
M13VBAB8. INSTALLATION OF FUEL FILTER
(1) When installing the fuel filter, first temporarily install the
filter to the filter bracket; then insert the main pipe at
the connector part of the high pressure fuel pipe, and
manually screw in the main pipe’s flare nut.
(2) Holding the fuel filter nut, tighten the fuel main pipe’s
flare nut and eye bolt at the specified torque. Then
tighten the filter to the bracket.
TSB Revision

13-154FUEL SYSTEM - Detonation Sensor
DETONATION SENSORREMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
l Release and Installation of the Air Intake Plenum
(Refer to GROUP
15-Air Intake Plenum.)
l Removal and Installation of the Intake Manifold
(Refer to GROUP 15
- Intake Manifold.)
l * +*I. Detonation sensor
20-25NmSERVICE POINT OF REMOVAL
1. REMOVAL OF DETONATION SENSOR
SERVICE POINT OF INSTALLATION
1. INSTALLATION OF DETONATION SENSOR
When the detonation sensor is installed, be sure to tighten
Idit precisely to the specified torque as its installation affects
the engine control.
TSB Revision

15-16INTAKE AND EXHAUST - Intake Manifold
INTAKE MANIFOLD
REMOVAL AND INSTALLATION
Pre-removal Operationl Release of Residual Pressure fromHigh Pressure Fuel Hose(Refer to GROUP 13-ServiceAdjustment Procedures.)l Draining of Engine Coolant (Refer
to GROUP 00 -Maintenance Service,)
l Removal of Air Intake Plenum(Referto P.15-13, 14.)5Nm
lo-13Nm4 ft.lbs.8-9ftJbs. w2\I
Post-installation Operationl Installation of Air Intake Plenum
(Refer to P.1.5-13. 14.)l Filling of Engine Coolant
(Refer to GROUP 00 - Maintenance
Service.)
l Adjustment of Accelerator Cable(Referto GROUP 13-EngineControl.). Checkina for Fuel Leakage6
5
2 :‘;bs.)
gp,.qgs ~-zt!EJ8OSFOO24
Removal steps
I. Connection for high-pressure fuel hose
2. O-ring
3. Connection for fuel return hose
4. Connection for vacuum hoses
5. Connection for injector connector
6. Delivery pipe (with injectors)
7. Insulators
8. Timing belt upper cover
I)*9. Intake manifold mounting nut I)* 10. Intake manifold mounting nut II. Cone disc spring
12. Intake manifold-
** 13. Intake manifold gasket
TSB Revision

17-1
EMISSIONCONTROL
.~
CATALYTIC CONVERTER............................:...Inspection
............................................................Removal and Installation
................................
CONTENTSM17.U. -
CRANKCASE EMISSION CONTROL
SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ComponentsLocation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Crankcase Ventilation System Inspection
._..Positive Crankcase Ventilation Valve
. . . . . . . . . . . .
EVAPORATIVE EMISSION CONTROL
SYSTEM................................................................Air Conditioner Switch
....................................Air Flow Sensor, Engine Coolant
Temperature Sensor and Intake Air
Temperature Sensor
........................................Canister
............................................................Components Location
....................................
FuelFiller CapInspection................................OverfillLimiter (Two-way Valve)
....................Purge Control Solenoid Valve
........................Purge Control System Inspection
....................................................Purge Control System Inspection

............................................................Purge Control Valve
........................
PurgePort VacuumCheck................................14
14
14
6
10
10
10
6
10
10
9
7
8
9
9EXHAUST GAS RECIRCULATION
(EGR)
SYSTEM. . . . . ..____._.._........__........_____.........................Air-FuelRatio Control (MPI) System. . . . . . . .
Components Location
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .EGR Control Solenoid Valve
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .EGR System Inspection
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .EGR Temperature Sensor
. . . . . . . .EGR Valve - Non Turbo, Turbo>
EGR Valve Control Vacuum Check
- Non Turbo, Turbo>. . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS................................................General Specifications
....................................Service Specifications
....................................
TROUBLESHOOTING. . . . . . . . . . . . . . . . . ..______...............
VACUUM HOSES................................................Inspection
............................................................Installation
........................................................VacuumHosesRouting
....................................
11
14
11
13
12
13
13
12
2
2
22

17-2EMISSION CONTROL - Specifications / Troubleshooting
SPECIFICATIONS
GENERAL SPECIFICATIONSMl’ICA- -\
Items
Crankcase emission control systemSpecifications
Closed type with positive crankcase ventilationvalve
Evaporative emission control systemCanister storage type
Canister
Charcoal type
Purge control solenoid valve
ON/OFF solenoid valve
Exhaust emission control system
Exhaust gas recirculation system
EGR valveVacuum-activated diaphragm type
EGR temperature sensor Thermistor type
EGR control solenoid valve - Non Turbo, Turbo>Duty cycle solenoid valve
Catalytic converter
Monolith type
Location
Under floor
Turbocharger outlet (front bank and rear bank,)
and under floor
SERVICE SPECIFICATIONSMl7CB-.
ItemsSpecifications
Purge control solenoid valve coil resistance
036 - 44 [at 20°C (68”F)I\
EGR temperature sensor resistancekfl60 - 83 [at 50°C (I 22”F)]
11 - 14 [at 100°C (212”F)l
EGR control solenoid valve coil resistance1236 - 44 [at 20°C (68”F)lI
TROUBLESHOOTING
Symptom
Engine will not start
or hard to start
Rough idle or engine
stalls
Probable cause
Vacuum hose disconnected or damaged
The EGR valve is not closed
Malfunction of the purge control solenoid valve
The EGR valve is not closed
Vacuum hose disconnected or damaged
Malfunction of the positive crankcase ventilationvalveRemedy
Repair or replace
Repair or replace
Repair or replace
Repair or replace
Repair or replace
Replace
Malfunction of the purge control systemCheck the system; if there is a
problem, check its component parts
Engine hesitates or3oor acceleration
Zxcessive oil:onsumptron
Malfunction of the exhaust gas recirculation
system
Positive crankcase ventilation line cloggedCheck the system; if there is a
problem, check its component parts
Check positive crankcase
ventila-tion system
Ioor fuel mileageMalfunction of the exhaust gas recirculation
systemTSB RevisionCheck the system; if there is a
problem, check its component parts
d

EMISSION CONTROL - Vacuum Hoses
VACUUM 1-10sEs
lVACUUM HOSES ROUTING
L//
17-3M17JA-
-
I’
Li
Fuel pressureregulator
Vehicle front
id
L: Light blueR: RedB: Black
7EM0131
EGR controlsolenoid valve
r-c,cud valve/
Canister
/Fuel pressureregulator
v
Vehicle frontG: GreenY: Yellow
L: Light blueR: RedB: Black
TSB Revision
7EM0132I
1