1991 MITSUBISHI 3000GT transmission

15-18INTAKE AND EXHAUST - Turbocharger (Front)
TURBOCHARGER (FRONT)
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Radiator(Refer to GROUP 14 - Radiator.)l Removal and Installation of Transmission
l Rerr
IPipeioval and Installation of Front Exhaust(Refer to P.15-31.)
lJl QG!?
IMlSLA-AI
40 - 47 ft.lbs.
1\29 - 11 ft.lbs.Removal steps
** 1. Air hose C*+2. Air intake hose B*+ 3. Air hose D4. Air hose Al *5. Air hose B.6. Air pipe B
l +7. Air hose E8. Air pipe C
9. Drive belt(Refer to GROUP 11 - Service
Adjustment Procedures.)
10. Alternator assembly(Referto GROUP 16-Alternator.)
11. Engine oil level gauge guide
12. Heat protector B-13Nm
‘9 ft.lbs.
-‘25
05FOO43
13. Water pipe A
14. Water pipe B
15. Connection of oxygen sensor
16. Turbocharger
& fitting assembly
17. Gasket
18. Ring
l * ** 19. Oxygen sensor
20. Turbocharger stay
21. Exhaust fitting
22. Gasket
23. Oil return pipe
l * 24. Turbocharger assemblyl *25. Air conditioner compressor
26. Tension pulley bracket
27. Air conditioner compressor bracket
28. Oil pipe
I
LJ
1 TSB Revision

15-30 INTAKE AND EXHAUST -Exhaust Pipe, Main Muffler and Catalytic Converter
EXHAUST PIPE, MAIN MUFFLER AND CATALYTIC CONVERTER
MlLRA-A
REMOVAL AND INSTALLATION
1. Main muffler and center exhaust50 Nm36
Fbs.
I\
yil / \2: h2yR ‘i”
3. Rubber hangers, ,4. Rubber nanger5. Main muffler6.Mouldings7.Hanger brackets8. Catalytic converter and center
exhaust pipe installation bolts
9.Hanger bracket10.Protector11.Rubber hangers12. Center exhaust pipe13.Gasket
---------179fl
/-r
9 ftlbs./----------------m _
I
!
14. Rubber hangers
15. Hanger bracket
16. Hanger brackets
17. Rear floor heat protector13 Nm
13 Nm
9 ftlbs.9 ft,lbs.5Nm
4 ft.lbs.
35hlm
25 ft.lbs.18. Catalytic converter and front
exhaust pipe installation bolts
19. Catalytic converter
20. Gasket
21. Oxygen sensor connection
22. Self-locking nuts9
ft.lbs.\/23.Rubberhanger24. Front exhaust pipe25.Gasket26.Hangerbracket27. Front floor heat protector
05FOO39
SERVICE POINTS OF REMOVAL
3.4. REMOVAL OF RUBBER HANGER / 5. MAIN MUFFLERSupport with a transmission jack, etc.
INSPECTIONMlSRCAM
l Check the mufflers and pipes for corrosion or damage.
l Check the rubber hangers for deterioration or damage.
l Check for gas leakage from mufflers and pipes.wision
1
L.J

15-32 INTAKE AND EXHAUST -Exhaust Pipe, Main Muffler and Catalytic Converter
SERVICE POINTS OF REMOVALMlBRBAA
4. 5. REMOVAL OF RUBBER HANGER / 6. MAIN MUFFLERSupport with a transmission jack, etc.
:iJ ~
30. REMOVAL OF OXYGEN SENSORDisconnect the connector of the oxygen sensor, and install
the special tool to the oxygen sensor.
INSPECTIONMlSRCAN
l Check the mufflers and pipes for corrosion or damage.
l Check the rubber hangers for deterioration or damage.
l Check for gas leakage from mufflers and pipes.
lCheck if the main muffler active exhaust system valve can\\be moved smoothly by hand.
SERVICE POINTS OF-INSTALLATIONMllRDAl
30. INSTALLATION OF OXYGEN SENSORUse the special tool to install the oxygen sensor.
3. INSTALLATION OF CABLE ASSEMBLY
Install with the paint mark facing up and adjust the adjusting
nut to obtain the illustrated dimension.
TSB Revision

22-1
iv,MANUAL ~
TRANSAXLE
~
I
CONTENTSM22AA. -
MANUAL TRANSAXLE . . . . . . . . . . . .._...48INPUT SHAFT ASSEMBLY_..________.............: . . . . . . . . . . . . . . . . . . . . . . . . . .30
GENERAL INFORMATION....................................................48
SERVICE ADJUSTMENT PROCEDURES
............................51
Drive Shaft OilSealsReplacement....................................
52Speedometer Cable Replacement....................................
53Transfer Oil Seal Replacement............................................53Transmission Oil Level Inspection....................................51Transmission Oil Replacement............................................51
SHIFT LEVER ASSEMBLY....................................................
53
SPECIAL TOOLS........................................................................50
SPECIFICATIONS
....................................................................49
General Specifications........................................................49Lubricants............................................................................49
TRANSAXLE ASSEMBLY....................................................56,60
TRANSAXLE CONTROL*........................................................54
TRANSFER ASSEMBLY
........................................................59
MANUAL TRANSAXLE ....................2
CLUTCH HOUSING ASSEMBLY............................................46
DIFFERENTIAL ASSEMBLY
....................................................43
5TH SPEED SYNCHRONIZER ASSEMBLY
........................28
GENERAL INFORMATION
....................................................2INTERMEDIATE GEAR ASSEMBLY
....................................
OUTPUT SHAFT ASSEMBLY................................................
SERVICE ADJUSTMENT PROCEDURES............................
Drive Shaft Oil Seals Replacement....................................Speedometer CableReplacement....................................Transmission Oil Level Inspection....................................Transmisston Oil Replacement............................................
SHIFT LEVER ASSEMBLY....................................................
SHIFT RAILS AND FORKS....................................................
SPECIAL TOOLS........................................................................
SPECIFICATIONS....................................................................
General Specifications........................................................
Lubricants............................................................................
Sealants and Adhesives........................................................Service Specifications........................................................
Snap Ring (for Adjustment) and Spacer............................
SPEEDOMETER DRIVEN GEAR ASSEMBLY....................
TRANSAXLE ASSEMBLY _____...._........__....................................
TRANSAXLE CONTROL*. . ..________.___.._ ..__._.__.__...............
36
41
9
10
9
9
9
13
42
6
3z
63
3
45
14
11TROUBLESHOOTING
___.._______._____.......,..................................8
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
(1)A Supplemental Restraint System (SRS), which uses a driver-side air bag, has been installed in the 3000GT.(2)The SRS includes the following components: impact sensors, SRS diagnosis unit: SRS warning light, air bagmodule, clock spring, interconnecting wiring. Other SRS-related components (that may have to be
removed/installed in connection with SRS service or maintenance) are indicated in the table of contents byan asterisk (*).
WARNING!(1)Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver (fromrendering the
SRS inoperative).(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B
-Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of theSRS or any SRS-related component.

22-6MANUAL TRANSAXLE - Specifications / Special Tools
LUBRICANTS
M22CD-A
Items
Manual transmission oil
Drive shaft oil seal lip
Specified lubricant
Hypoid gear oil, SAE
75W-90 or75W-85W conforming to APIclassification GL-4 or higherQuantity lit.
(qts)
2.3 (2.4)
As required
SEALANTS AND ADHESIVES
Items
Transaxle case - clutch housing mating surfaces
Transaxle case
- rear cover mating surfaces
Differential drive gear bolts
Bearing retainer screw (flush head screw)
Reverse brake cone mounting screw bolts
MUCE- _
Specified sealants and adhesives
Mitsubishi genuine part No. 997740 or equivalent
3M Stud Locking part No. 4170 or equivalent
Air breather
3M ATD part No. 8001 or equivalent
SPECIAL TOOLSM22DA-A.
nstallation of spring pin and lock
MD998323-01TSB Revision

MANUAL TRANSAXLE - Service Adiustment Procedures22-9
110*u011009FO12
SERVICE ADJUSTMENT PROCEDURES
MZZFBAEl
TRANSMISSION OIL LEVEL INSPECTIONRefer to GROUP 00
- Maintenance Service.
TRANSMISSION OIL REPLACEMENTM22FCAI(1) Position vehicle on a flat level.
(2) Remove filler and drain plugs and allow the transmission oil
to drain.
(3) Refill the transaxle to the proper level with specified
transmission oil. The oil level should be the bottom of the oil
filler hole.
Transmission oil: Hypoid gear oil, SAE 75W-85W con-
forming to API classification GL-4 or
higherC2.3 liters (2.4 pts.)]
SPEEDOMETER CABLE REPLACEMENTMUFEALl
1.Correctly insert the adapter into the instrument panel, and
fasten the new speedometer cable.
2.Install the grommet so that, as shown in the illustration, the
cable attachment part and the projecting part are horizontal.
CautionThe cable arrangement should be made so that the
radius of cable bends is 150 mm (5.9 in.) or more.
3.At the transaxle end of the speedometer cable, the key joint
should be inserted into the transaxle, and the nut should be
securely tightened.
Caution
If the cable is not correctly and securely connected, it
may cause incorrect indication. by the speedometer, orabnormal noise. Be sure to connect it correctly.
DSB RevisionI

22-10 MANUAL TRANSAXLE - Service Adjustment ProceduresI
I09K5671160024
Oil seallip
* Transaxleside2200037
DRIVE SHAFT OIL SEALS REPLACEMENTM2ZFDAI
(I) Disconnect the drive shaft from the transaxle.
(Refer to GROUP 26
- Drive Shaft.)’ )
(2) Using a flat-tip (-) screwdriver, remove the oil seal.d,(3) Using the special tool, tap the drive shaft oil seal into the
transaxle.
The drive shaft oil seal must be installed in the direction
shown.
(4) Apply a coating of the transmission oil to the lip of the oil
seal.
Transmission oil: Hypoid gear oil, SAE 75W-90 or
75W-85W conforming to API classi-
fication GL-4 or higher
‘d
TSB Revision

MANUAL TRANSAXLE - Transaxle Assembly22-15
idPost-installation Operationl Installation of Front Under Cover(Referto GROUP 51 -Front Bumper.)l Supplying of Transmission Oil (Refer to P.22-9.)l Filling of Engine Coolant (Refer to GROUP 14-
Service Adjustment Procedures.)70 Nm
l Checking Operation of Shift Lever at Each Positionl Checking the Operation of the Meters and Gauges26
ft.lbs.09FOO84
4*9. Connection for transaxle mount16. Starter10. Transaxle mount bracket4*17. Drive shaft (Left side),
l * 11. Mounting stopperinner shaft assembly12. Transaxle assembly upper part+* ** 18. Drive shaft (Right side)
coupling bolt19. Transaxle stay (Front bank side)4*13. Connection for tie rod end20. Transaxle stay (Rear bank side)4*14. Connection for lower arm4*21. Transaxle assembly lower part
ball jointcoupling bolt15. Right member4*22. Transaxle assembly
SERVICE POINTS OF REMOVALMZZMBBA6. DISCONNECTION OF THE CLUTCH TUBE BRACKET
AND CLUTCH DAMPER ASSEMBLY
Remove the clutch release cylinder and clutch oil line
bracket installation bolt, and then secure at the body side
without disconnecting the oil line coupling.
1 TSB Revision