1991 MITSUBISHI 3000GT Drive belt

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
dir J
bag module, clock spring, interconnecting wiring. Other SRS-related comp\
onents (that may have to be
(*).
The Supplemental Restraint System (SRSI-related components are shown in the following MASTER TABLE
OF CONTENTS. Be sure to carefully read and understand the WARNING below \
before proceeding.
Group number
22.23
32
36
42
52A
Group nameSRS-related components
FUELCRUISE CONTROL SYSTEM/ P.13-185
MANUALTRANSAXLE.TRANSAXLE CONTROLAUTOMATIC TRANSAXLE
POWER PLANT MOUNTRIGHT MEMBER, LEFT MEMBER AND CROSSMEMBERP.32-6
ELECTRONIC CONTROLSUSPENSION’STEERING ANGULAR VELOCITY SENSORP.33B-19
PARKING BRAKESPARKING BRAKE LEVER AND PARKiNG BRAKE CABLE/ P.36~5I
STEERING/POWER STEERING GEAR BOX/ P.37A-17
/STEERING WHEEL AND SHAFTj P.37A-13
BODY
INTERIOR
FENDER
FLOOR CONSOLE/ P.52A-11
FRONT SEAT
INSTRUMENT PANEL
P52A-18
P.52A-8
CHASSIS ELECTRICAL
SEAT BELT
COLUMN SWITCH
HORN SWITCH
IGNITION SWITCH
P.52A-25
P.54-73
P.54-78
1 P.54-6
RADIO REMOTE-CONTROL/ P.54.110
HEATER, AIR CONDITIONERAIR-CONDITIONER CONTROL PANELAND VENTILATIONAIR-CONDITIONER CONTROL UNITP.55-56
/DAMPER CONTROL MOTOR ASSEMBLYI
/HEATER CONTROL ASSEMBLY1 P.55-18I
HEATER UNIT.1 P.55-22
WARNING!
VENTILATORS (INSTRUMENT PANEL)P.55-36
(1) Improper service or maintenance of any component of the SRS, or an\
y SRSrelated component,
can lead to personal injury or death to service personnel (from inadver\
tent firing of the air bag) or
to the driver (from rendering the SRS inoperative).
(260°F) in baking or in
drying after painting, remove the SRS components (air bag module, SRS d\
iagnosis unit, front
perfarmed
only at an authorized MITSUBISHI dealer.
52B
- Supplemental Restraint System (SRS), before beginning any service or m\
aintenance of any
component of the SRS or any SRS-related component.
1 TSB RevisionI

,
b
00-I
GENERALCONTENTS
MOOOA- .
GENERAL DATA AND SPECIFICATIONS . . . . . .21
HOW TO USE THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . .3Definition of Terms
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Explanation of Circuit Diagrams
. . . . . .._...........7Explanation of Manual Contents
. . . . . . . . . . . . . . . . . . . .4
Explanation of the Troubleshooting Guide . .
6ModelIndications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Scope of Maintenance, Repair and
ServicingExplanations
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Troubleshooting
. . . . . . .._.......................................3
LUBRICATION AND MAINTENANCE. . . . . .._....31SCHEDULED MAINTENANCE TABLE. . . . . . .._.
MAIN SEALANT AND ADHESIVE TABLE. . .44
MAINTENANCE SERVICE
. . . . . . . . . . . . . . . .._......_.....__Air Cleaner Element
. . . . . . .._......._......_................Automatic Transaxle
. . . . . . . . . . . . . . . . . . . . . . . . .._......._.....Ball Joint and Steering Linkage Seals
. . . . . . . . . . . .
BrakeHoses. . . . . . . . . . . . . . . . . . . . . . . . . . . .._......._.._...._......._..
Disc Brake Pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Drive Belt (For Alternator)
. . . . . . . . .._.........._..........Drive Shaft Boots
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Engine Coolant
. . . . . . . . . . . . ..__.._.............................Engine Oil
.._....__._.................................................Engine Oil Filter
. . . . .._._.......__.................. . . . . . . . . . . .Exhaust System
_....._......._.....__._............,...........Fuel Hoses
..__......__............................................36
3740
42
42
42
38
43
41
38
39
43
36
FuelSystem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Manual Transaxle
. . . . . . . . . .._........................_.......Rear Axle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._..._.._..____.._.......
SparkPlugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._...............TimingBelt
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MASTER TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS BEFORE SERVICE. . . . . . . . . . . . . . . .
RECOMMENDED LUBRICANTS AND
LUBRICANT CAPACITIES TABLE. . . . . . .._........
SPECIAL HANDLING INSTRUCTIONS
FOR AWD MODELS. . . . . . . . . . . . .._...._........................
TIGHTENING TORQUE. . . . . . . . . . . . . . . ..__.....................
TOWING AND HOISTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . .._.....Chassis Number .
.._............................................Engine Model Stamping
.._..........................._...._Theft Protection
. . . . .._.........................................Vehicle Identification Code Chart Plate
.._.....Vehicle Identification Number List
.._._....._..._.Vehicle Identification Number Location
. . . .._
Vehicle Information Code Plate . . . . .._._......_.......Vehicle Safety Certification Label
. . . ..I . . . . .._..._...
36
3943
37
3724
1532
35
20
23
16
8
10
11
11
8
9
8
10
10

00-8
GENERAL - Vehicle Identification
VEHICLE IDENTIFICATIONMOOCA- _VEHICLE IDENTIFICATION NUMBER LOCATION
The vehicle identification number
(V.I.N.) is located on a plate1Jattached to the left top
s3e of the instrument panel.
VEHICLE IDENTIFICATION CODE CHART PLATE
MOOCB- .All vehicle identification numbers contain 17 digits. The vehicle
number is a code which tells country, make, vehicle type, etc.
J-JapanA-3-X-D-s-Mitsubishi4-B-PassengerDriver13000GTM-PremiumY-
Car3-door3.0 liters000001
Air Bag,FWD6F’a;;;;ger E-Hatchback (181.4 win.)z1991
SpecialL:oHC-MP’lYearl%ya99iJF389
3000GT 7-Seat BeltAWDUltimate3.0 liters 1(181.4 cu.in.1[DOHC-MPI-Turbo]
NOTEl “Check digit” means a srigle number or letter X used to verify the accuracy of transcription of vehicle identification number,
TSB Revision

00-38GENERAL - Maintenance Service
6. DRIVE BELT (For Alternator)
00F0006
:Vehicles with air conditioner>OOFOO07
A: Crankshaft pulleyB: Tension pulleyC: Alternator pulleyD: Idler pulleyE: ,Air conditioner compressor pulley
OlLO183
OlLO18:(Inspect tension)
MOOS88(1(1) Measure the deflection with a force of
100 N (22 Ibs.)applied to belt mid-point between pulleys shown in the
illustration. If the standard value is not obtained, make
adjustment.
Standard value: 4.0
- 5.5 mm (.157 - 216 in.)
(2) On vehicles without air conditioner, set a tension gauge at a
position marked with
r3 in the illustration to measure the
belt tension.
7. ENGINE OIL
(Inspect oil level)
(I) Check to see that the engine oil level is within the range
indicated on the oil level gauge.
(2) Make sure that engine oil is not very dirty or is free from
coolant or gasoline and has an appropriate viscosity grade.J
(Change)
MOOSAAHAlways use lubricants which conform to the requirements of
the API classification “For Service SG” or “For Service
SGKD”when available, and have the proper SAE grade number for the
expected temperature range.
Never use nondetergent or straight mineral oil.
(1) After warming up the engine, remove the oil ‘filler cap.
(2) Remove the drain plug and drain the engine oil.
(3) Tighten the drain plug to 40 Nm (29 ft.lbs.).
(4) Pour new engine oil through the oil filler.
Caution
1.Cover the alternator with waste cloth or the like before
pouring engine oil to make sure that even if oil is spilt,it may not drop on the alternator.
2. Use an oil mug or a funnel to pour oil.
Engine oil total capacity:4.0 liters (4.2 qts.)
[excluding oil filter 0.3 liter (l/2 qt.)
and oil cooler 0.21 liter (l/2 qt.)](5) Check to ensure that the engine oil level is within the level
range indicated on the oil dip stick.
TSB Revision

11-I
ENGINECONTENTS
IMllAA--
CAMSHAFT OIL SEALS....................................
CRANKSHAFT, FLYWHEEL AND
DRIVEPLATE........................................................
CYLINDER BLOCK................................................
CYLINDER HEAD AND VALVE........................
CYLINDER HEAD GASKET................................
ENGINE ASSEMBLY............................................
ENGINE OIL COOLER........................................
GENERAL INFORMATION................................
lbLubricationSystem............................................SectionalView
....................................................
OIL PAN AND OIL PUMP....................................
OIL PAN AND OIL SCREEN................................20
49
5334
23
17
552
3
240
22
PISTON AND CONNECTING ROD....................
ROCKER ARM AND CAMSHAFT....................
SERVICE ADJUSTMENT PROCEDURES........Compression Pressure Check
........................Curb Idle Speed Inspection
............................Drive Belts Tension Adjustment
....................Ignition Timing Adjustment
............................
LashAdjusters
Check........................................Manifold Vacuum
Inspection
.............................
SPECIAL TOOLS....................................................
SPECIFICATIONS................................................General Specifications
....................................
Sealants
.......................................
.....................Service Specifications
....................................
TIMING BELT........................................................
TROUBLESHOOTING........................................44
31
11
15
14
11
13
16
16
84
4
84
26
10

ENGINE - Specifications
/
L
L/
Items
Connecting rod bearing
Oil clearancemm (in.)
Crankshaft main bearing
Oil clearancemm (in.)
Crankshaft
Pin O.D.
mm (in.)
Journal O.D.mm (in.)
Out-of-roundness of journal and pin
mm (in.)
Taper of journal and pin
mm (in.)
End playmm (in.)
Oil pressure at curb idle speed
kPa (psi)
[Conditions: oil temperature is 75 to 90°C
(167 to
194”F)l
Standard value
0.016- 0.046 (.0006- .0018)
0.019 - 0.044 (.0007 - .0017)
49.9 (I ,965)
59.9 (2.358)
Less than 0.003 (.00012)
Less than 0.005 (0002)
0.05 - 0.25 (0020 - .0098)
80 (I 1.4) or more
Limit
0.1
(.004)
0.1 (.004)
0.3 (.012)
Oil pump
Side clearancemm (in.)
Body clearance0.100-0.181 (.0039-.0071)
Side clearance0.040 - 0.095 (.0016 - .0037)
Relief spring
Free lengthmm (in.)43.8 (1.724)
Load
137 N (8.3 Ibs.)]mm (in.)40.1 (1.579)
Drive belt
For alternator (Vehicle without air
conditioner)
Deflectionmm (in.)
Inspection
4.0-5.5(.157-,216)
New belt3.5-4.0(.138-,157)
Used belt4.0-5.0 (.157- ,197)
TensionN (Ibs.)
Inspection350 - 600 (77 - 132)
New belt650
- 850 (143 - 187)
Used belt450
- 600 (99 - 132)
For alternator and air conditioner
compressor
Deflectionmm (in.)
Inspection
4.0-5.5(.157-,216)
New belt3.5-4.0 (1388.157)
Used belt4.0-5.0(.157-,197)
For power steering pump
Deflection
mm (in.)9.0
- 11 .o (354 - ,433)
Timing belt
Amount of projection of auto tensioner3.8-4.5(.149-,177)rodmm (in.)(distance between the tensioner arm andauto tensioner body)
1 TSB Revision

ENGINE - Service Adjustment ProceduresII-IISERVICE ADJUSTMENT PROCEDURES

AlternatorTension pulley
IIdler pulley/
Tension pulleyCrankshaftpulleyOlFOOO

Tenston pulley
Air conditionerCrankshaftcompressor pulleypulleyOlFOO8
,
MllFMBGDRIVE BELTS TENSION ADJUSTMENT
(1) Check that the belts are not damaged and are properly fit
,into the pulley grooves.
Caution1. When installing the V-ribbed belt, check that the
V-ribs are properly fit without misalignment.
2. If creaking or slippage is observed, check the belt
for wear, damage, or breakage on the pulley contact
surface, check the pulley for scoring, in addition to
sag inspection.3. Check that the V-ribbed belt is not resting on the
tension pulley or idler pulley flange.
(2) Apply 100 N (22
Ibs.) force to the belt back midway
between the pulleys as shown in the illustration, measure
the deflection or by using a belt-tension gauge, check the
belt’s tension.
Standard value:
Tension350-600650-850450-600N (Ibs.)(77-132)(143-187)(99-132)
For P/S
pump
ItemsAdjustment valueCheck valueNew beltUsed belt
TSB Revision

II-12ENGINE - Service Adjustment Procedures-
r
AdJl
bolt
Alternator wllev
haft
Fixing nutOlFOOO8
Alternator pulley
Adjusting bolt
/Crankshaftpulley
Air contionercompressorpulleyw Tension pulleyFlxtng nutOlN007.
Crankshaft pulleyOlN007TENSION ADJUSTMENT OF THE ALTERNATOR DRIVE
BELT
I(1) Remove front under cover panel ’
aero> (Refer to GROUP 51 - Aero Parts.).\\
3 ’
(2) Remove under covers (front L.H., side L.H.).
(3) Loosen tension pulley fixing nut.
(4) Adjust belt deflection with adjusting bolt.
(5) Tighten fixing bolt.
(6) Run the engine one time or more.
(7) Check the belt tension. Readjust, if necessary.
(8) Install under covers.
DEFLECTION ADJUSTMENT OF THE ALTERNATOR AND
AIR CONDITIONER COMPRESSOR DRIVE BELT with air conditioner>
(1) Use straight handle box wrench to loosen tension pulley
fixing nut.
(2) Adjust belt deflection with adjusting bolt.
(3) Use straight handle box wrench to tighten fixing nut.
(4) Run the engine one time or more.
(5) Check the belt deflection. Readjust, if necessary.
DEFLECTION ADJUSTMENT OF POWER STEERING PUMP
DRIVE BELT(1) Insert an extension bar (insertion depth 12.7 mm), etc. into
the opening at the end of the tension pulley bracket.
(2) Loosen the tension pulley fixing bolts in the order of B and
(3)
iove the extension bar installed to the tension pulley in the‘LJdirection of arrow to adjust the belt tension.
(4) Tighten the tension pulley fixing bolts in the order of A and
8.Tightening torque: 35
- 50 Nm (25 - 36 ftlbs,)(5) Give the crankshaft two turns in normal direction (clock-
wise) to run in the belt.
(6) Check the belt deflection. Readjust, if necessary.
1 TSB Revision