1991 MITSUBISHI 3000GT differential

MANUAL TRANSAXLE - Specifications22-3
SPECIFICATIONS
L
GENERAL SPECIFICATIONSM22CA.A
items
Model
Applicable engine
Type
Gear ratio
1 st
2nd
3rd
4th
5th
Reverse
Final reduction ratio
Speedometer gear ratio (driven/drive)
Oil quantityliters (qts.)
Specifications
F5M33-2-SNZR
6G72-DOHC MPI
5-speed transaxle floor shift
3.090
1.833
1.217
0.888
0.741
3.166
4.153
28136
2.3 (2.4)
SERVICE SPECIFICATIONSM22CB-A
mm (in.)
L.J
Items
Standard value
Transaxle
Input shaft end play
Input shaft rear bearing end play
Intermediate gear bearing end play
Intermediate gear preload
Output shaft preload
Differential
Differential case preload
Differential pinion backlash
Limit
Specifications
0 - 0.05 (0 - ,002)
0.01 - 0.09 i.0004 - ,004)0.01 -0.14 (.0004-
,006)
0.05 - 0.10 (.002 - ,004)
0.05 - 0.10 (.002 - ,004)
0.05 - 0.10 (.002 - .004)
0.025 - 0.150 (.OOl - ,006)
Synchronizer ring and clutch gear clearance0.5 (.02)
SNAP RING (FOR ADJUSTMENT) AND SPACERM22CF.A
Part name
Spacer
(For adjustment of input shaft end play)Thickness mm (in.)
0.80
i.0315)
0.83 (.0327)
0.86(.0338)
0.89t.0350)
0.92
(.0362)
Identificationsymbol
80
83
86
89
92
Part No.
MD727661
MD720937
M D720938
MD720939
MD720940TSB Revision

MANUAL TRANSAXLE - Specifications22-5
Part name
Spacer
(For adjustment of output shaft preload)
Spacer
(For adjustment of differential case preload)
Spacer
(For adjustment of differential pinion backlash)Thickness mm (in.)IdentificationsymbolPart No.
0.83 (.0327)83MD720937
0.86
(0338)86MD720938
0.89
(.0350)89MD720939
0.92
(.0362)92MD720940
0.95
(.0374)95MD720941
0.98 (.0386)98MD720942
1
.Ol t.0398)01MD720943
1.04 (.0409)04MD720944
1.07 (.0421)07MD729945
1 .I 0 (.0433)JMD71 0454
1
.I 3 (.0445)DMD700270
1.16(.0457)KMD71 0455
1 .I9 (0468)LMD71 0456
1.22 (.0480)GMD700271
1.25 (0492)MMD710457
1.28
(.0504)NMD710458
1.31
(.0516)EM D706574
1.34 (0527)0MD71 0459
0.80 (0315)80MD727661
0.83 (0327)83M D720937
0.86 (.0338)86M D720938
0.89 (0350)89M D72d939
0.92 (0362)92MD720940
0.95
(.0374)95M D720941
0.98 (.0386)98MD720942
1
.Ol (.0398)01MD720943
1.04 (.0409)04MD720944
1.07 (0421)07MD720945
1 .I 0 (.0433)JMD71 0454
1.13 (.0445)DMD700270
1.16
(.0457)KMD710455
1.19
(.0468)LMD71 0456
1.22 (.0480)GMD700271
1.25 LO4921MMD71 0457
0.75
- 0.82-MA1 80862
LO295 - .0323)
0.83 - 0.92-MA1 80861
(0327 - .0362)
0.93 - 1 .oo-MA1 80860(0366
- .0394)
1.01 -1.08-MA1 80875
(.0398 - .0425)1.09-1.16
-MA1 80876
t.0429 - .0457)TSB Revision

22-6MANUAL TRANSAXLE - Specifications / Special Tools
LUBRICANTS
M22CD-A
Items
Manual transmission oil
Drive shaft oil seal lip
Specified lubricant
Hypoid gear oil, SAE
75W-90 or75W-85W conforming to APIclassification GL-4 or higherQuantity lit.
(qts)
2.3 (2.4)
As required
SEALANTS AND ADHESIVES
Items
Transaxle case - clutch housing mating surfaces
Transaxle case
- rear cover mating surfaces
Differential drive gear bolts
Bearing retainer screw (flush head screw)
Reverse brake cone mounting screw bolts
MUCE- _
Specified sealants and adhesives
Mitsubishi genuine part No. 997740 or equivalent
3M Stud Locking part No. 4170 or equivalent
Air breather
3M ATD part No. 8001 or equivalent
SPECIAL TOOLSM22DA-A.
nstallation of spring pin and lock
MD998323-01TSB Revision

MANUAL TRANSAXLE - Special Tools22-7
MD998348-0 1
Bearing remover
Removal of gears and bearings of input
shaft, intermediate gear and output shaft
andintermediate shaft lock nut
M
D998808-01Snap ring installerInstallation of input shaft rear snap ring
MD998822installer adapterInstallation of differential case bearings
iTSB Revision

MANUAL TRANSAXLE - Transaxle Assembly
15-22Nm5211-15
ft.lbs..I 53
-22Nm
-15 ftlbs.
67
litI63
62
51.Screw52.Bolt53.Bearing retainer54. Intermediate gear assembly
55. Input shaft assembly
56. Output shaft assembly
57. Differential gear assembly
58. Bearing outer race
59. Bearing outer race60.Oil guide61. Bearing outer race
62. Bearing outer race
** 63. Oil seall 464.Oil seal65.Magnet66.Magnet holder
67. Clutch housing assembly
TSB Revision

MANUAL TRANSAXLE - Transaxle Assembly
22-25
L
Slit
#Jl
Spring pin
/
II-+Shift rail1 I I201034
er
2150008
MD998325-01
(2) When installing, make sure that the slit of the spring pinis aligned with the shift rail center line.
46. INSTALLATION OF REVERSE IDLER GEAR SHAFTInstall in the direction illustrated.
35.37. 40. 42. INSTALLATION OF SPACERS
(1) Place two pieces of solder measuring about 10 mm (.4in.) in length and 1.6 mm
(.06 in.) in diameter as
illustrated and install the outer races.
(2) Install the transaxle case and tighten the bolts to
specified torque.
(3) Remove the transaxle case.
(4) Remove the outer races and remove the solder.
(5) If solder is not crushed, perform steps (1) to (4) with a
solder with a larger diameter.
(6) Measure the thickness of the crushed solder with a
micrometer and select and install a spacer of thicknessthat gives standard preload and end play.
Standard value:Input shaft end play
0
- 0.05 mm (0 - .002 in.)
Intermediate gear preload
0.05
- 0.10 mm (.002 - .004 in.)
Output shaft preload
0.05
- 0.10 mm (.002 - .004 in.)
Differential case preload0.05
- 0.10 mm (.002 - .004 in.)
33. INSTALLATION OF OIL SEALInstall the drive shaft oil seal using the special tool.
visionI

22-26MANUAL TRANSAXLE . - Transaxle Assembly
Amountl-2 mm
27. INSTALLATION OF OIL GUIDEInstall the oil guide to the transaxle case as illustrated.
26. INSTALLATION OF TRANSAXLE CASE(1) Place the selected spacers on the intermediate gear
and differential’s bearing outer race. Also insert the
selected spacer between the output shaft bearing outer
race and the transaxle case.
(2) Set so that the threaded hole of the reverse idler gearshaft’s head is facing in the direction indicated in the
illustration.
NOTE
If there is a great deviation in the direction in which the
threaded hole is facing, it will be impossible to align thethreaded hole and the hole in the case after the
transaxle case is installed.
(3) Apply specified sealant to the clutch housing side of the
transaxle case.
Specified’ sealant: MITSUBISHI genuinePart No. MD997740 or equiva-
lentLJ
Caution
Squeeze out sealant from the tube uniformly with-
out excess or discontinuity.(4) Install the transaxle case onto the clutch housing.
(5) Insert a Phillips screwdriver
[8 mm (.32 in.) shaft
diameter] into the bolt hole in the case, as shown in thefigure, and use it to align the threaded hole of the
reverse idler gear shaft with the bolt hole in the
transaxle case.
(6) Install the reverse idler gear shaft bolt and tighten thebolt by fingers.
(7) Tighten the all transaxle tightening bolts to specified
torque.(8) Tighten the reverse idler gear shaft bolt to specified
torque.16.15. INSTALLATION OF LOCK NUTS
(1) Install the special tool to the splined end of input shaft.(2) Screw a bolt
[lo mm (.40 in.)] into the hole on the
periphery of clutch housing and attach a spinner handleto the special tool.
TSB Revision

MANUAL TRANSAXLE - Differential Assembly22-43
DIFFERENTIAL ASSEMBLY
IDISASSEMBLY AND REASSEMBLY
Disassembly steps
** 1. Bolt2. Differential drive gear** *+3. Taper roller bearingl * l +4. Lock pinl *5. Pinion shaftl * 6. Pinion
l * 7. Washer
** 8. Side gearl *9. Spacer (Select)10. Differential caseTFM0054
/Adhesive: 3M Stud Locking- . .] _PartNo.417Ooreqr
130-i40Nnl94- 101 ft.lbs.
Press
ti Bearmg
SERVICE POINTS OF DISASSEMBLY
3. REMOVAL OF TAPER ROLLER BEARING
Remove the taper roller bearing using the special tool as
illustrated.
Caution1. Do not reuse the bearing removed from the dif-
ferential case.
2.Replace the inner and outer races of the taper rollerbearing as a set. ,
TSB Revision