1991 LEXUS SC400 ignition buzzer

INDICATOR
1. Turn the ignition switch on while pressing the ari conditioner control
switch and REC swich
simultaneously.
2. Check that all the indicators light up and go off at 1 second intervals 4 times in succession.
3. Check that the buzzer sounds when the indicators light up in 2.
HINT:
wAfter the indicator check is ended, the diagnostic code
check begins automatically.
w Press the OFF switch when desiring to cancel the check
mode.
DIAGNOSTIC CODE CHECK (SENSOR
CHECK)
1. Perform an indicator check. After the indicator check is completed, the system enters the diagnostic code check
mode automatically.
2. Read the code displayed on the panel. Refer to the list of
codes on page AC±28 when reading the codes. (Codes are
output at the temperature display.)
If the slower display ped is desired, press the FRS
switch and change it to stepped operation. Each time the
FRS
switch is pressed, the display changes by 1 step.
HINT:
w If the buzzer sounds when a code is being read, it means
the trouble indicated by that code continues to occur.
w If the buzzer does not sound when a code is being read,
it means the trouble indicated by that code occurred ear-
lier (such as poor connector contacts, etc.)
CLEARING DIAGNOSTIC CODES
1. Pull out the DOME fuse in Relay Block No. 2 for 10 sec. or
longer to clear the memory of diagnostic codes.
2. After reinserting the fuse, check that the normal code is output.
±
AIR CONDITIONING SYSTEM TroubleshootingAC±27
WhereEverybodyKnowsYourName

6. TILT UP REMINDER SYSTEMIf the ignition switch is turned from ON to OFF or ACC and the sliding roof rem\
ains tilted up, after 60 seconds
have elapsed or either the driver or passenger door is opened, a buzzer will\
sound for approx. 8 seconds
as a reminder that the sliding roof is tilted up.
Parts Location
±
BODY ELECTRICAL SYSTEM Sliding Roof SystemBE±177
WhereEverybodyKnowsYourName

Troubleshooting
You will find the cause of trouble more easily by properly using the tabl\
e shown below. In this table, the numbers
indicate the order of priority of the causes of trouble. Check each part in the \
order shown. If necessary, replace
the part.
See page
BE±4,21BE±4,21BE±4,20BE±4,20BE±156BE±152BE±180BE±179BE±179 ±±BE±181BE±26BE±79BE±4,20 ±±
Part
name
Trouble
AM1 FuseDOME FuseDOOR FusePOWER FuseTheft Deterrent and Door Lock Control ECUPower Window Main RelaySliding Roof Control RelaySliding Roof SwitchSliding Roof MotorSliding Rood Motor (Stones to foreign material
trapped in motor assembly)Limit SwitchIgnition SwitchDoor Courtesy SwitchECU±IG FuseWire Harness
*1 Sliding roof system does not operate.1234
*2 Sliding roof system does not operate.35467892110
Sliding roof system operates abnormally.1324
Sliding roof system stops operation half way.1342
Buzzer does not sound.123
Buzzer sounds abnormally.1
ªKey±off Sliding Roofº operation does not
operate.124536
*1: Door Lock does not operate
*2: Door Lock is normal
BE±182
±
BODY ELECTRICAL SYSTEM Sliding Roof System
WhereEverybodyKnowsYourName

199
6. TILT UP REMINDER SYSTEM
WITH THE IGNITION SW IS TURNED TO ACC OR OFF WITH THE MOON ROOF STILL TILTED UP, KEY OFF MOON ROOF OPERATION
CAUSES CURRENT TO FLOW TO TERMINAL 6 OF THE MOON ROOF CONTROL RELAY FOR A PERIOD OF APPROX. 60 SECONDS OR
UNTIL THE DRIVER'S DOOR OR PASSENGER'S DOOR IS OPENED. WHEN KEY OFF MOON ROOF OPERATION ENDS AND THE
CURRENT FLOW IS STOPPED, THE MOON ROOF CONTROL RELAY RECEIVES A SIGNAL THAT THE IGNITION SW IS OFF. MOON
ROOF LIMIT SW NO. 1 AND NO. 2 ARE OFF AT THIS TIME, SO THE SIGNAL IS INPUT TO TERMINALS 8 AND 9 OF THE MOON ROOF
CONTROL RELAY, INDICATING THAT THE MOON ROOF IS IN THE TILT UP CONDITION. THIS CURRENT TO THE MOON ROOF
CONTROL RELAY FLOWS TO TERMINAL 12 OF RELAY " BUZZER " TERMINAL 11 " GROUND, CAUSING THE BUZZER TO SOUND
FOR APPROX. 8 SECONDS. TO INFORM THE DRIVER THAT THE MOON ROOF IS IN THE TILT UP POSITION.
POWER MAIN RELAY
3±5 : CLOSED WITH IGNITION SW AT ON POSITION
M 2 MOON ROOF CONTROL RELAY
11±GROUND : ALWAYS CONTINUITY 6±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON, AND MOON ROOF CONTROL SW AT CLOSE OR UP POSITION
(EXCEPT APPROX. 200MM (7.9 IN) BEFORE FULLY CLOSED POSITION)
5±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON, AND MOON ROOF CONTROL SW AT OPEN OR DOWN POSITION
M 3 MOON ROOF CONTROL SW
1±4 : CLOSED WITH MOON ROOF CONTROL SW AT UP POSITION
2±4 : CLOSED WITH MOON ROOF CONTROL SW AT CLOSE POSITION
3±4 : CLOSED WITH MOON ROOF CONTROL SW AT DOWN POSITION
5±4 : CLOSED WITH MOON ROOF CONTROL SW AT OPEN POSITION
4±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
D1030M 331T 8B29
D1130M4A31T 9A29
M 231M 4B31
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1D20FRONT DOOR LH WIRE
1F20ROOF WIRE
1H
1I20COWL WIRE1J20COWL WIRE
1K
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
BZ140ROOF WIRE AND MOON ROOF WIRE (FRONT SIDE OF ROOF LEFT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
IJ36RIGHT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B 140ROOF WIREB 340MOON ROOF WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

184
UNLOCK AND SEAT BELT WARNING
1E
12
3A
4
3D
13
1B
5 2
B
1
A
7
1E 1
1H
13
1D
10
1J
1 1C
12 1D 8
1I
15
9
10
6 3
2
1
BK
IF 10A
DOME
10A
GAUGE
SEAT BELT
WARNING LIGHT
[COMB. METER]
INTEGATION RELAY
BUZZER TI M ER
UNLOCK
WARNING SW
[IGNITION SW] BUCKLE
SW LH
DOOR OPEN
DETECTION
SW LH
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
FROM POWER SOURCE SYSTEM(
SEE PAGE 56 )
C12 ,C 14
D10
B4
I15
R
R
Y
Y
W±B
W±B
W±B
Y
W±B
W±B
W±B W±B B±L B±L
R±W
W±B
W±B
V
86
5
10 179
AB
1 2
(W/ MEMORY )
( W/O MEMORY )
( W/ MEMORY )
( W/O MEMORY )
Ba1
14
Ba2
5 Ba2
6 Ba1
11
WhereEverybodyKnowsYourName

185
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 7 OF THE INTEGRATION RELAY.
AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE INTEGRATION RELAY AND, FOR APPROX. 4±8 SECONDS, CURRENT FLOWING
THROUGH THE WARNING LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY " TERMINAL 10 " GROUND, CAUSING THE WARNING
LIGHT TO LIGHT UP. AT THE SAME TIME AS THE WARNING LIGHT LIGHTS UP, A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8
OF THE RELAY, THE CURRENT FLOWING TO TERMINAL 7 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT
BELT WARNING BUZZER SOUNDS FOR APPROX. 4±8 SECONDS. HOWEVER, IF THE SEAT BELT IS PUT ON DURING THIS PERIOD
(WHILE THE BUZZER IS SOUNDING), SIGNAL INPUT TO TERMINAL 8 OF RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 7
OF THE RELAY " TERMINAL 10 " GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK SW ON), THE IGNITION SW STILL OFF AND \
DOOR OPEN (DOOR
COURTESY SW ON), WHEN A SIGNAL IS INPUT TO TERMINAL 6 OF THE RELAY, THE INTEGRATION RELAY OPERATES, CURRENT
FLOWS FROM TERMINAL 7 OF THE RELAY " TERMINAL 10 " GROUND AND UNLOCK WARNING BUZZER SOUNDS.
B 4 BUCKLE SW LH
1±2 : CLOSED WITH DRIVER'S LAP BELT IN USE
D10 DOOR COURTESY SW LH
3±6 : CLOSED WITH LH DOOR OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
10±9: CLOSED WITH IGNITION KEY IN CYLINDER
INTEGRATION RELAY
10±GROUND: ALWAYS CONTINUITY6±GROUND: CONTINUITY WITH DRIVER'S DOOR OPEN
5±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND: CONTINUITY WITH DRIVER'S LAP BELT IN USA
9±GROUND: 0 VOLTS FOR 4±8 SECONDS WITH IGNITION SW ON AND APPROX. 12 VOLTS 4±8 SECONDS AFTER IGNITION SW ON
1±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 432C14B28I1529
C12A28D1030
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1C20FLOOR MAIN
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)Ba242FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
BK40UNDER THE CENTER PILLAR LH
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName