1991 LEXUS SC400 engine oil

223
COMBINATION METER
B 1 BRAKE FLUID LEVEL SW
1±2 : CLOSED WITH FLOAT DOWN
P 3 PARKING BRAKE SW
1±GROUND : CLOSED WITH PARKING BRAKE LEVER PULLED UP
O 2 OIL PRESSURE SW
1±GROUND : CLOSED WITH OIL PRESSURE BELOW APPROX. 0.2 KG/CM2 (2.8 PSI, 20 KPA)
W 3 WATER TEMP. SENDER
1±GROUND : APPROX. 226
(50 °C, 122 °F)
APPROX. 25
(11 5 °C, 239 °F)
E 6 ENGINE OIL LEVEL WARNING SW
1±2 : CLOSED WITH FLOAT UP AND ENGINE OIL TEMP. AT BELOW APPROX. 55°C ( 131 °F)
OPEN WITH FLOAT DOWN AND ENGINE OIL TEMP. AT BELOW APPROX. 60°C ( 140 °F)
F18(A) FUEL SENDER
2±3 : APPROX. 3
AT FUEL FULL
APPROX. 11 0
AT FUEL EMPTY
C14 (C) COMBINATION METER
1±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
12±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ST POSITION AND SHIFT LEVER AT P OR N RANGE
10±GROUND : ALWAYS CONTINUITY
22±GROUND : ALWAYS CONTINUITY
11±GROUND : ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1026E 626R 929
B 126F17B30S 327
C12A28F18A30S22B29
C13B28I 227S23A29
C14C28I16A29T1529
D 128O 227W 127
D 228P 329W 327
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
IE20INSTRUMENT PANEL WIRE
1G20COWL NO. 2 WIRE
1H
1I20COWL WIRE1J20COWL WIRE
1K
3A
3B
3C
3D22INSTRUMENT PANEL WIRE
3E
3F
3H
SERVICE HINTS
WhereEverybodyKnowsYourName

26
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
A 1 A/C Ambient Temp. Sensor E 1 ECT Solenoid
A 2 A/C Lock Sensor and A/C Magnetic Clutch E 2 EFI Water Temp. Sensor
A 3 A/C High Pressure SW E 3 EGR Gas Temp. Sensor (for USA Spec.)
A 4 ABS Actuator E 5 Engine Hood Courtesy SW
A 5 ABS Actuator (w/ Traction Control) E 6 Engine Oil Level Warning SW
A 6 ABS Actuator (w/ Traction Control)
A 7 ABS Speed Sensor Front LH F 1 Front Airbag Sensor LH
A 8 ABS Speed Sensor Front RH F 2 Front Airbag Sensor RH
A 9 Air Flow Meter F 3 Front Clearance Light LH
A 10 Alternator F 4 Front Clearance Light RH
A 11 Alternator F 5Front Side Marker Light LH
A 33 ABS Actuator (w/o Traction Control) F 6 Front Side Marker Light RH F 7 Front Turn Signal Light LH
B 1 Brake Fluid Level SW F 8 Front Turn Signal Light RH
B 6 Back±Up Light SW (for M/T) F 9 Fuse Block
C 3 Check Connector H 1 Headlight Hi LH
C 6 Cornering Light LH H 2 Headlight Hi RH
C 7 Cornering Light RH H 3 Headlight Lo LH
C 8 Cruise Control Actuator H 4 Headlight Lo RH H 5 Horn LH
D 13 Distributor H 6 Horn RH
WhereEverybodyKnowsYourName

27
Position of Parts in Engine Compartment
I 1 ISC Valve S 3Speed Sensor No. 1
I 2 Igniter S 4 Speed Sensor No. 2 (for ECT)
I 4 Ignition Coil S 6 Starter
I 6 Injector No. 1 S 7 Starter
I 7 Injector No. 2 S 8 Sub Throttle Actuator
I 8 Injector No. 3 S 9 Sub Throttle Position Sensor
I 9 Injector No. 4
I 10 Injector No. 5 T 1 Theft Deterrent Horn
I 11 Injector No. 6 T 2 Throttle Position Sensor T 3 Traction Brake Actuator
K 1 Knock Sensor No. 1 (on Front Side) T 4 Traction Brake Actuator
K 2 Knock Sensor No. 2 (on Rear Side) T 5 Traction pump and Motor
N 1 Neutral Start SW, Back±Up Light SW and A/T Indicator SW V 1 VSV (for EGR) (Exc. USA Spec) (for A/T) V 2 VSV (for EVAP)
N 2 Noise Filter (for Defogger System) V 4 VSV (for Water Valve)
N 3 Noise Filter (for Ignition System) V 7 VSV (for Intake Control Valve)
O 2 Oil Pressure SW W 1 Washer Level SW
O 3 Oxygen Sensor Main No. 1 (on Front Side) W 2 Washer Motor
O 4 Oxygen Sensor Main No. 2 (on Rear Side) W 3 Water Temp. Sender W 5 Wiper Motor
P 1 PPS Solenoid
P 20 Power Steering Pressure SW
WhereEverybodyKnowsYourName

66
.
ENGINE CONTROL
THIS SYSTEM UTILIZES AN ECU AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE O\
F
THE ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) WATER TEMP. SIGNAL CIRCUITTHE WATER TEMP. SENSOR DETECTS THE ENGINE COOLANT TEMP. AND HAS A BUILT±IN THERMISTOR WITH A RESISTANCE
WHICH VARIES ACCORDING TO THE WATER TEMP. THE WATER TEMP. IS INPUT INTO TERMINAL THW OF ENGINE CONTROL
ECU AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE AIR FLOW METER AND DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT
AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL ECU.
(3) OXYGEN SENSOR SIGNAL CIRCUIT THE OXYGEN DENSITY IN THE EXHAUST EMISSION IS DETECTED AND INPUT AS A CONTR\
OL SIGNAL FROM THE OXYGEN
SENSOR NO. 1 AND NO. 2 TO TERMINALS OX1, OX2 OF THE ECU AND FROM THE OXYGEN SENSOR SUB (FOR CALIFORNIA) TO
TERMINAL OX3 OF THE ECU.
TO STABILIZE DETECTION PERFORMANCE BY THE OXYGEN SENSOR SUB (FOR CALIFORNIA)\
IS WARMED. THIS HEATER IS
ALSO CONTROLLED BY THE ECU (HT).
(4) RPM SIGNAL CIRCUIT CRANKSHAFT POSITION IS DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR. CRANKSHAFT POSITION
IS INPUT AS A CONTROL SIGNAL TO TERMINALS G1 AND G2 OF THE ECU, AND RPM IS INPUT TO TERMINAL NE.
(5) THROTTLE SIGNAL CIRCUIT THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA1 OF THE ECU. WHEN THE VALVE IS COMPLETELY CLOSED, THE CONTROL SIGNAL IS INPUT INTO
TERMINAL IDL1 .
(6) VEHICLE SPEED CIRCUIT THE VEHICLE SPEED IS DETECTED BY SPEED SENSOR NO. 1 INSTALLED IN THE TRANSMISSION AND THE SIGNAL IS INPUT TO
TERMINAL SPD OF THE ECU VIA THE COMB. METER.
(7) NEUTRAL START SIGNAL CIRCUIT THE NEUTRAL START SW DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR NOT, AND THE SIGNAL IS INPUT INTO
TERMINAL NSW OF THE ECU.
(8) AIRCONDITIONING SW SIGNAL CIRCUIT THE OPERATING VOLTAGE OF THE A/C MAGNETIC CLUTCH IS DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL ACMG OF
ECU AS A CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ECU. WITH THE IGNITION SW TURNED ON, THE VOLTAGE FOR
ECU START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B AND +B1 OF ECU VIA EFI MAIN RELAY.
THE CURRENT FLOWING THROUGH THE IGN FUSE FLOWS TO TERMINAL IGSW OF THE ECU.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT INTAKE AIR VOLUME IS DETECTED BY THE AIR FLOW METER AND THE SIGNAL IS INPUT TO TERMINAL KS OF THE ECU AS A
CONTROL SIGNAL.
(11) STOP LIGHT SW SIGNAL CIRCUIT THE STOP LIGHT SW IS USED TO DETECT WHETHER OR NOT THE VEHICLE IS BRAKING AND THE SIGNAL IS INPUT INTO
TERMINAL STP OF THE ECU AS A CONTROL SIGNAL.
(12) STA SIGNAL CIRCUIT TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ECU AS A CONTROL SIGNAL.
(13) ENGINE KNOCK SIGNAL CIRCUIT ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGN\
AL IS INPUT INTO TERMINALS KNK1 AND
KNK2 AS A CONTROL SIGNAL.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

236
GROUND POINT
FRONT TURN SIGNAL
LIGHT LH
ENGINE HOOD
COURTESY SW
TRACTION PUMP AND
MOTOR
HEATER RELAY
ABS ACTUATOR RELAY
TELEPHONE
TRANSCEIVER
AND SPEAKER RELAY
ENGINE OIL LEVEL
WARNING SW
COMBINATION METER
(E1 )
EFI ECU
TRACTION ECU
CHECK CONNECTOR
(
E1 ) CORNERING LIGHT LH
FRONT SIDE MAKER
LIGHT LH
BRAKE FLUID LEVEL
SW
FRONT CLEARANCE
LIGHT LH
FRONT SIDE MAKER
LIGHT RH
FRONT CLEARANCE
LIGHT RH
ABS ACTUATOR
FRONT TURN SIGNAL
LIGHT RH
CRUISE CONTROL
ACTUATOR
OXYGEN SENSOR SUB
(
FOR USA SPEC. )
TDCL (
E1 )
WASHER LEVEL SW EFI MAIN RELAY
CORNERING LIGHT RH
A/C PRESSURE SW
(HI GH PRESSURE )
AIR FLOW METER POWER STERRI NG
PRESSURE SW
NOISE FI LTER
(
FOR IGNI TION SYSTEM ) E4
E10
E12 2
2
BS1 4 E4
E7
E1 E5
EB EA I23
I33
E1 6
I32
E20
E20
E20
IK2 24
ED EC IK1
1 BY1
5
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W± B W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B BR
BR
W±B BR
BR
BR
W±B BR
BR±B BR BR
BR
BR
W± B
W± B
W± B
W± B
W± B
W± B
W± B
W±B
W±B
BR
BR
BR
BR BR
BR
BR
W±B
BR BR
BR
( EO1 )
( E11 )
( E1 )
( EO2 )
I27BR
(
S1 )
( E1 )
NOISE FILTER (
FOR
IGNITION SYSTEM )W±B
W/ TRACTION SYSTEM
NOI SE FILTER
(
FOR DEFOGGER SYSTEM )
W±B
W±B
WhereEverybodyKnowsYourName

109
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 7 OF THE INTEGRATION RELAY THROUGH GAUGE
FUSE. VOLTAGE IS APPLIED AT ALL TIMES TO TERMINAL (A)4 (USA), (B)11 (CANADA) OF THE INTEGRATION RELAY THROUGH THE
TAILLIGHT RELAY COIL, AND TO TERMINAL (A)5 (USA), (B)12 (CANADA) THROUGH THE HEADLIGHT RELAY COIL.
1. NORMAL LIGHTING OPERATION
TURN TAILLIGHT ON
WITH LIGHT CONTROL SW TURNED TO TAILLIGHT POSITION, A SIGNAL IS INPUT INTO TERMINAL (A)3 (USA), (B)10 (CANADA) OF
THE INTEGRATION RELAY. DUE TO THIS SIGNAL, THE CURRENT FLOWING TO TERMINAL (A)4 (USA), (B)11 (CANADA) OF THE RELAY
FLOWS TO TERMINAL (A)3 (USA), (B)10 (CANADA) " TERMINAL 3 OF THE LIGHT CONTROL SW "TERMINAL 4 " TO GROUND AND
TAILLIGHT RELAY CAUSES TAILLIGHT TO TURN ON.
TURN HEADLIGHT ON
WITH LIGHT CONTROL SW TURNED TO HEADLIGHT POSITION, A SIGNAL IS INPUT INTO TERMINALS (A)3 (USA). (B)10 (CANADA)
AND (A)6 (USA), (B)13 (CANADA) OF THE INTEGRATION RELAY. DUE TO THIS SIGNAL, THE CURRENT FLOWING TO TERMINAL (A)5
(USA), (B)12 (CANADA) OF THE RELAY FLOWS TO TERMINAL (A)6 (USA), (B)13 (CANADA) " TERMINAL 13 OF THE LIGHT CONTROL
SW " TERMINAL 4 " TO GROUND IN THE HEADLIGHT CIRCUIT, AND CAUSES TAILLIGHT AND HEADLIGHT RELAY TO TURN ON. THE
TAILLIGHT CIRCUIT IS SAME AS ABOVE.
2. LIGHT AUTO TURN OFF OPERATION
WITH LIGHTS ON AND IGNITION SW TURNED OFF (INPUT SIGNAL GOES TO TERMINAL 7 OF THE RELAY), WHEN DOOR ON DRIVER'S
SIDE IS OPENED (INPUT SIGNAL GOES TO TERMINAL 6 OF THE RELAY), THE RELAY OPERATES AND THE CURRENT IS CUT OFF
WHICH FLOWS FROM TERMINAL (A)4 (USA), (B)11 (CANADA) OF THE RELAY TO TERMINAL (A)3 (USA), (B)10 (CANADA) IN TAILLIGHT
CIRCUIT AND FROM TERMINAL (A)5 (USA), (B)12 (CANADA) TO TERMINAL (A)6 (USA), (B)13 (CANADA) IN HEADLIGHT CIRCUIT.
AS A RESULT, ALL LIGHTS ARE TURNED OFF AUTOMATICALLY.
HEADLIGHT RELAY 1±2 : CLOSED WITH LIGHT CONTROL SW AT HEAD POSITION OR DIMMER SW AT FLASH POSITION
TAILLIGHT RELAY 5±3 : CLOSED WITH LIGHT CONTROL SW AT TA I L OR HEAD POSITION
I16(A)(B) INTEGRATION RELAY
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
6±GROUND : CONTINUITY WITH DOOR LH OPEN
(A) 4, (B) 11±GROUND: ALWAYS APPROX. 12 VOLTS
(A) 5, (B) 12±GROUND: ALWAYS APPROX. 12 VOLTS
(A) 6, (B) 13±GROUND: CONTINUITY WITH LIGHT CONTROL SW AT HEAD POSITION
(A) 3, (B) 10±GROUND: CONTINUITY WITH LIGHT CONTROL SW AT TA I L OR HEAD POSITION
D10 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH
3±6 : CLOSED WITH DOOR LH OPEN
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1528F 926I16B29 (CANADA)
D1030I16A29 (USA)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
423LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1D20FRONT DOOR LH WIRE
1J20COWL WIRE1K20COWL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136ENGINE WIRE AND COWL WIRE (R/B NO.4)
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName

567 8
1LEXUSSC300(
Cont ' d )
2EC2 1EC2
7IJ1
1
345
12
B±O
B B
B±O
21
B±O
B±O
BL
B±O
W± L
B±O
W±Y
Y± G
W±Y
Y±G To Engine and ECT ECU º IGT1º < 2±8>
To Engine and ECT ECU º IGF1º < 2±8>
To Check Connec tor º IG±º < 2±4>
IGF IGT +B C±
TAC
I2
IGNITER
NO. 1
I4
IGNITION COIL
NO. 1DI STRI B UT OR
N3
NOISE FILTER
(
for Ignition System )
Ignition
B±O
8IK1 ToComb. MeterºTACHOº<21±7>
B± OB
WhereEverybodyKnowsYourName

567 8
4LEXUSSC300(
Cont ' d )
1
2
1
2 1D
11 E 1I
10
3G
1
1B
2
3A
9
1C
10
1E
20
1H
1
9BU1
1Bd15IG7
11 Bc 1
Be1 2 1
1
2
3A
10
1 2
3 84
921117
3G
83A 2
3A
1
2
12
1
1
4
1
2 1
2
EA BM BL 2Bd14
1
3
8
2 10
3H
3
3C
3
3F
2
3G
5
3H
1
3F 6
1
2
1
3
2
2
9
5
1
10
F 5
G
IQ1
2
6
7 IQ1
4
12
3A 9
3E 6
3E 6
3E
6
3H 2
3H 1
3H 1
2
10 11 1 2
GW±G
G
G
GW±G W± GW±G
GW±G
G±O
G±O
G±O
G±O
G±O W±G W± G W± G
W± G W± G
W± G
G± W
W± BY Y
G±O
G
G
W± L
G
G
G
GW±BW± B W± B W± B
G
Y
V± G
V± G Y
G±W
G± W
W±B
GGGG
G
W
G± W
G± W
B
W± B R± W
B
G±W G±W G±O
G±O
W± B W
W±GBR
Y± V L±B L
W±B
W± B
W± B
W±B
W±B
G
G
W± G W± G
W±B
±PK ±STP E HS +STP
ETCRLRVREILL±
7
G± O
G± O
+PK BWRN
T
15A
STOP
F3
LH
F4
RH
FRONT
CLEARANCE LI GHT
L3
LI GHT FAILURE SENSOR
RE AR LI GHT WARNI NG
LI GHT[ COMB. MET ER]
S12
STOP LIGHT SW
To ABS ECU<8±3><9±4>
To Shif t Lock ECU< 15±2>
G2
GLOVE BOX
LI GHT SW
F5
LH
F6
RH
FRONT SIDE
MARKER LIGHT
L2
LI CE NCE
PLATE LIGHT
W± B W±B
W±BH9
HIGH MOUNT
STOP LIGHT
H8
HIGH MOUNT
STOP LIGHT A1
A/C CONTROL
ASSEMBLY
A15
A / C C ON TR OL SW
AND RADIO SW
RADIO AND PLAYER
( w/o CD Player )
R4
RADIO AND PLAYER
( w/ CD Player )
T1 2
TRACTION CUT SW AND
SEAT HEATER SW
C1 1
CIGARETTE LIGHTER
A21
A/T INDICATOR LIGHT E8
ECT PATTERN
SELECT SW
T1 5
TRIP SW AND THEFT DETERRENT
INDICATOR LI GHT
R9
RHEOSTAT
G1
GLOVE BOX
55
13 13W±B
W±B
W± B W± B W± B
R± W
G±R
R± W G±R G±RTAI L AND
STOP LIGHT
[REAR COMB.
LIGHT]
R1 0
LH
R1 1
RH
TAIL
ST OP
TAIL
ST OP
To Engine and ECT ECU< 2±3>
To Traction ECU< 8±8>
To Cr uise Control ECU< 16±4>
To Cruise c ont rol
ECU< 16±4>
To Po wer Se at E CU
(Driver' s )
< 11±5>
G± W
G±W
(
* 1 )
(
* 2 )
( * 2 )
(
* 1
)
C13 , C14
ED
H
H
H
H
I3C
1
17
2345
COMBINATI ON METER C12 , C14 IH R5 , R6
FG
12 34
5678910
12
3456
RADIO AND PLAYER
(
w/ o CD Pl ay er )
Taillight and Stop Light (
for USA )
Illumination(
for USA )
*2:
(
w/o Rear Spoiler )
*
1: (
w/ Rear Spoiler )
W
G±W
G± O
Fro nt s i de of
right fender Under t he
c ent er pillar RH
Back panel c ent er 23
G
W± G
H7
HA ZA RD SW
10 11 12 13 17 18 19 20 21
12345 6789
14 15 16
17 18
1 2345 6789 10
23
22
21
20
19
15
14
13
12
11 16 C1 2 I
C1 4 H
COMBI NATI ON METER
RE AR LI GHT WARNI NG
LI GHT[ COMB. MET ER]
WhereEverybodyKnowsYourName