1991 LEXUS SC400 exhaust

EXHAUST GAS RECIRCULATION (EGR) SYSTEM
DESCRIPTION
To reduce NOx emission, part of the exhaust gases are recirculated through\
the EGR valve to the intake man-
ifold to lower the maximum combustion temperature.
OPERATION
To reduce NOx emission, part of the exhaust gases are recirculated through\
the EGR valve to the intake manifold to lower the
maximum combustion temperature.
Coolant
Temp.VSVThrottle Valve OpeningPressure in the EGR Valve Pressure ChamberEGR VacuumModulatorEGR
ValveExhaust Gas
Below 45
COPENCLOSEDNot recircu-
(113
F)OPEN±±±CLOSEDlated
Positioned be-
low EGR port±±CLOSEDNot recircula- ted
Above 50 5C
(122 5F)CLOSEDPositioned be-
tween EGRport
(1)
LOW* Pressure constantly
alternating between
OPENS passage to atmosphereCLOSEDNot recircula- ted
tween EGR port
and R port(2)
HIGHalternating between
low and highOPENS passage
to atmosphereOPENRecirculated
Above 50 5C
(122 5F)CLOSEDPositioned
above R port(3)
HIGH**CLOSES passage to atmosphereOPENRecirculated(increase)
* Pressure increases Modulator closes EGR valve opens Pressure drops EGR Valve closes Modulator opens
** When the throttle valve is positioned above the R port, the EGR vacuum m\
odulator will close the atmosphere passage and
open the EGR valve to increase the EGR gas, even if the exhaust pressure\
is insufficiently low.
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) SystemEC±11
WhereEverybodyKnowsYourName

INSPECTION OF EGR SYSTEM
1. CHECK AND CLEAN FILTER IN EGR VACUUMMODULATOR
(a) Remove the cap and filter.
(b) Check the filter for contamination or damage.
(c) Using compressed air, clean the filter.
(d) Reinstall the filter and cap.
HINT: Install the filter with the coarser surface facing the at-
mospheric side (out ward).
2. INSPECT SYSTEM OPERATION (a) Connect the tachometer to terminal IG ± of the check(ºDIAGNOSISº) connector.
(b) Using SST connect the terminals TE1 and E1 of the check (ºDIAGNOSISº) connector.
SST 09843±18020
(c) Keep the engine at 3,500 rpm with the transmission in ºNº position.
(d) Remove the SST from the check connector.
SST 09843±18020
EC±12
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName

(e) Check whether the engine rpm increases 100±300 rpmunder the following conditions:
Coolant temp.
Below 45 5C (113 5F) . . . NO increase
Above 50 5C (122 5F) . . . Increases
INSPECTION OF VSV
1. REMOVE VSV
(a) Disconnect the VSV connector.
(b) Disconnect the two vacuum hoses from VSV.
(c) Remove the bolt and VSV from the intake manifold.
2. INSPECT VSV (a) Inspect VSV for open circuit.Using an ohmmeter, check that there is continuity be-
tween the terminals.
Resistance (Cold): 33±39

If there is no continuity, replace the VSV.
(b) Inspect VSV for ground.
Using an ohmmeter, check that there is no continuity be-
tween each terminal and the body.
If there is continuity, replace the VSV.
(c) Inspect VSV operation: 1) Check that the air flows from ports E to G
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) SystemEC±13
WhereEverybodyKnowsYourName

2) Apply battery voltage across the terminals
3) Check that the air flows from port E to port G
If operation is not as specified, replace the VSV.
3. REINSTALL VSV (a) Install the VSV with the nut.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(b) Connect the following hoses:
(1) Vacuum hose (from throttle body)
(2) Vacuum hose (from EGR vacuum modulator)
(c) Connect the VSV connector.
INSPECTION OF EGR VACUUM
MODULATOR
1. DISCONNECT VACUUM HOSES FROM EGR VACUUM MODULATOR
Disconnect the three vacuum hoses from ports P, Q and R of
the EGR vacuum modulator.
2. INSPECT EGR VACUUM MODULATOR OPERATION (a) Block ports P and R with your finger.
(b) Blow air into port Q, and check that the air passesthrough to the air filter side freely.
(c) Start the engine, and maintain speed at 2,500 rpm.
(d) Repeat the above test. Check the there is a strong resistance to air flow.
3. RECONNECT VACUUM HOSES TO EGR VACUUM MODULATOR
Connect the three vacuum hoses to the proper locations.
EC±14
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName

INSPECTION OF EGR VALVE
1. REMOVE EGR VALVE(a) Disconnect the following hoses:(1) Vacuum hose from EGR vacuum modulator
(2) Pressure hose from EGR vacuum modulator(USA Spec.)
(b) Disconnect the EGR Gas Temp. Sensor connector
(c) Loosen the nut for EGR pipe.
(d) Remove the two nuts, EGR valve and gasket.
2. INSPECT EGR VALVE Check for sticking and heavy carbon deposits.
If a problem is found, replace the EGR valve assembly.
3. REINSTALL EGR VALVE (a) Place a new gasket on the intake manifold.
(b) Install the EGR valve with the two nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(c) Torque the nut for EGR pipe.
Torque: 64 N Vm (650 kgf Vcm, 47 ft Vlbf)
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) SystemEC±15
WhereEverybodyKnowsYourName

(d) Connect the following hoses:(1) Vacuum hose from EGR vacuum modulator
(2) Pressure hose from EGR vacuum modulator(USA Spec.)
(e) Connect the EGR Gas Temp. Sensor connector.
EC±16
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName

EXHAUST GAS RECIRCULATION (EGR) SYSTEM
DESCRIPTION
To reduce NOx emission, part of the exhaust gases are recirculated through\
the EGR valve to the intake
manifold to lower the maximum combustion temperature.
OPERATION
Coolant Temp.ConditionEGR ValveExhaust Gas
Below 53 5C (127 5F)±CLOSEDNot recirculated
Above 55 5C (131 5F)(a)Idling, Deceleration, Neutral,
Low air volume, High Engine speedCLOSEDNot recirculatedAbove 55 C (131 F)
Except (a)OPEN*Recirculated
* The ECU calculates the appropriate number of steps according to the in\
take air volume and the engine speed, then
drives the stepping motor to maintain the EGR volume at a level appropri\
ate to the driving conditions.

±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) SystemEC±15
WhereEverybodyKnowsYourName

OPERATION (Cont'd)
EC±16±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName