1991 ACURA NSX center console

BRACKET BEAM
COTTER PIN

Replace.

SELECT

LEVER PIN SELECT LEVER
MOUNTING BOLT
SHIFT CABLE

HOLDER

6 x 1.0 mm
12 N .
m

(1.2 kg-m, 9 Ib-ft)

6 x 1.0 mm

8 N .
m (0.8 kg-m, 6 Ib-ft)
SHIFT CABLECLAMPS
SHIFT CABLE

COVER

LOCK PIN
Install in this
direction. CONTROL

LEVER
LEVER
CONTROL

SRS MAIN

HARNESS Make sure lifts are placed properly.
1. Remove the center console panel (see section 20).

2. Remove the shift cable by removing the cotter pin and
selector lever pin from the selector lever, and mount-

ing bolts from the bracket beam.

3. Remove the shift cable clamps.

4. Remove the shift cable holder and shift cable cover.
5. Remove the shift cable by removing the lock pin and
control lever pin from the control lever.

CAUTION: Take care not to bend the calbe when
removing it.
6. Install the shift cable in the reverse order of removal.
7. Check the cable adjustment on reassembly, on page
14-157.

Shift Cable
Removal/Installation
All SRS wiring harnesses are covered with yellow
outer insulation.Before disconnecting any part of the SRS wire
harness, install the short connectors (see page
23-328).

Replace the entire affected SRS harness assembly if
it has an open circuit or damaged wiring.
CAUTION:

PINProCarManuals.com

Carpet
Replacement
SRS wire harnesses are routed near the carpet. CAUTION:
Remove:
2. Detach the clips at the front edge (passenger's). 3, Remove the console carpet attaching screw from the heater unit (passenger's).
4. Disconnect the air duct (driver's) and air vent, then remove the carpet hooks from the dashboard inside screws.
DASHBOARD

INSIDE SCREW
CARPET
HOOK
(3)

AIR VENT

AIR DUCT
AIR VENT

CLIPS
FLOOR
CARPET
CONSOLE
CARPET

CONSOLE CARPET LEFT DASH
SENSOR
PASSENGER'S

AIRBAG
RIGHT DASH

SENSOR

SRS
MAIN

HARNESS
SRS UNIT

Side sill pad (See page 20-38) Rear side trim panel (See page 20-38)
Center armrest (See page 20-49)
Center console panel (See page 20-52)

SRS UNIT
SCREW
(cont'd)
Seats (See page 20-39)
Footrest
Under-dash fuse box lid (See page 20-38)
Side sill trim (See page 20-38)

All SRS wiring harnesses are covered with
yellow outer insulation.
Before disconnecting any part of the SRS wire
harness, install the short connectors (see page

23-328).
Replace the entire affected SRS harness assem-
bly if it has an open circuit or damaged wiring.ProCarManuals.com

Dashboard

Component Removal/Installation
Clock and center air vent removal:
NOTE: Take care not to scratch the dashboard and

related parts.
1. Remove the clock by pulling it backward from the center air vent, then disconnect the connector.
2. Remove the center air vent mounting screws.
Disconnect the connector.
CLOCK

CENTER AIR

VENT

CENTER AIR VENT

MOUNTING SCREWS
3. Inset a plastic plate between the center air vent and center console panel to prevent damage them.

CENTER AIR VENT

CENTER CONSOLE

PANEL

PLASTIC PLATE

(Thin plate)4. To make a gap between the center air vent and
dashboard, pull the top of the center air vent whilelowering it as shown.
NOTE: Make a gap thoroughly.

DASHBOARD
CENTER AIR

VENT

PLASTIC

PLATE

5. Inset a flat tip screwdriver between the center air vent and dashboard as shown.
NOTE: Use a flat tip screwdriver as following.

3.3 mm
(0.13
in)

max.

CENTER AIR

VENT

DASHBOARD
PLASTIC

PLATE
HOOKS

FLAT TIP

SCREWDRIVERProCarManuals.com

Dashboard

Component Removal/Installation (cont'd)
SRS wire harnesses are routed near the dashboard. CAUTION:
LEFT DASH
SENSOR PASSENGER'S

AIRBAG
RIGHT DASH
SENSOR

SRS MAIN

HARNESS
SRS UNIT

Center console panel removal:

NOTE:

Disassemble in numbered sequence.
ASHTRAY
CENTER CONSOLE PANEL

Disconnect the

connectors.

SRS
UNIT
Lift up the parking

brake lever.

Installation is the reverse of the removal procedure. NOTE: Make sure the connectors are connected properly.All SRS wiring harnesses are covered with
yellow outer insulation.
Before disconnecting any part of the SRS wire
harness, install the short connectors (see page

23-328).
Replace the entire affected SRS harness assem-
bly if it has an open circuit or damaged wiring.
Take care not to scratch the dashboard, center console panel and related parts.Do not drop the screws inside the dashboard.
Remove the center armrest (see page 20-49), clock and center air vent (see page 20-50).ProCarManuals.com

Climate control unit, stereo cassete/radio and glove box removal:

Disassemble in numbered sequence.

NOTE: Remove the center console panel.

CLIMATE CONTROL

UNIT

Disconnect the connectors.

SRS UNIT

STEREO

CASSETE RADIO

Disconnect the connectors.

GROUND CABLE

Passenger's:

GLOVE BOX
Disconnect the connectors.

PASSENGER'S

AIRBAG

DASHBOARD LOWER

COVER (Passenger's)
TRUNK LID OPENER

MAIN SWITCH

GLOVE BOX

LID

Installation is the reverse of the removal procedure.

NOTE: Make sure the connectors are connected properly.

(cont'd)ProCarManuals.com

Replacement

SRS wire harnesses are routed near the dashboard and

steering column.
CAUTION:All SRS wiring harnesses are covered with
yellow outer insulation.Before disconnecting any part of the SRS wire
harness, install the short connectors (see page
23-328).

Replace the entire affected SRS harness assem-
bly if it has an open circuit or damaged wiring.
LEFT DASH

SENSOR
PASSENGER'S

AIRBAG

RIGHT DASH
SENSOR

SRS MAIN

HARNESS
SRS UNIT

1. To remove the dashboard, first remove the: Seats (See page 20-39('93-'96))
Dashboard lower cover (Driver's) (See page
20-54))

Knee bolster and pad (See page 20-54)
Dashboard brace (See page 20-54)
Center armrest (See page 20-49)

Clock, center air vent and console panel (See

pages 20-50, 51, 52)

Climate control unit and stereo cassette/radio
(See page 20-53)Dashboard lower cover (Passenger's) (See page

20-53)

Glove box lid and glove box (See page 20-53)

2. Lower the steering column (see section 17).
To avoid accidental deployment and NOTE:
Remove the access panel, then remove the
short connector (RED). Disconnect the connec-
tor between the airbag and cable reel, then con- nect the short connector (RED) to the airbag

connector.

AIRBAG
CONNECTOR
CABLE REEL

CONNECTOR
ACCESS PANEL SHORT CONNECTOR

(RED)

Connect the special tool to the cable reel

connector.

CABLE REEL
CONNECTOR
SHORT
CONNECTOR
(RED)

SRS
SHORT CONNECTOR

07MAZ–SP00200

(cont'd)

possible injury always install the short connector
on the airbag connector when the SRS wire
harness is disconnected.ProCarManuals.com

SRS wire harnesses are routed near the carpet.

CAUTION:
All SRS electrical wiring harnesses are covered with yellow outer insulation.
Before disconnecting the SRS wire harness, install the short connector on the airbag (see page 23-323).
Replace the entire effected SRS harness assembly if it has an open circuit or damaged wiring.
1. To remove the carpet, first remove the: Seats (page 20-39)
Footrest
Under-dash fuse box lid (page 20-38)

Side sill trim (page 20-38)

• Side silt pad (page 20-38)
• Rear side panel (page 20-38)
• Center armrest (page 20-38)
• Center console panel (page 20-43)

CARPETHOOK

(3)

CONSOLE CARPET

FOOTREST MOUNTING

BOLTS

5. Installation is the reverse of the removal procedure. NOTE:
Take care not to damage, wrinkle or twist the carpet.

Make sure the console carpet air vents are inserted into the heater unit and air duct.

Make sure the seat harnesses are routed correctly.

Carpet

Replacement

SRS UNIT

SRS MAIN

HARNESS FLOOR CARPETS

SRS UNIT

CONSOLE
CARPETS
CONSOLE
CARPET

FLOOR

CARPET INSIDE SCREW
CLIPS

AIR DUCT

CONSOLE

CARPET

FOOTREST

2. Pull up the retainers and carpet clips at the front edge (passenger's side), then remove the floor carpet.
3. Remove the console carpet attaching screw from the heater unit (passenger's side).
4. Remove the carpet hooks from the dashboard inside screws, then remove the console carpet.

L. DASH

SENSOR
R. DASH

SENSORProCarManuals.com

Dashboard/Center Armrest

Component Removal/Installation

SRS wire harnesses are routed near the dashboard.
CAUTION:
All SRS electrical wiring harnesses are covered with yellow outer insulation.Before disconnecting the SRS wire harness, install the short connector on the airbag (see page 23-323). Replace the entire effected SRS harness assembly if it has an open circuit or damaged wiring.
NOTE: Take care not to scratch or score the dashboard.Do not drop the screws inside the dashboard.
When prying with a flat tip screwdriver, wrap it with protective tape or shop

towel to prevent damage.

Disassemble in numbered
sequence.
CLOCK

CLOCK

CENTER AIR VENT
CENTER ARMREST
INNER PANEL
ASHTRAY

SRS UNIT

CENTER ARMREST CENTER CONSOLE

PANEL
Lift up the parking
brake lever.

HEATER CONTROL UNIT

SRS UNIT

STEREO
CASSETE/RADIO

Disconnect the

connectors.

GLOVE BOX LID
(cont'd)

DASHBOARD LOWER
PANEL (Passenger's side)
GLOVE BOX
Disconnect the connectors
TRUNK LID OPENER

MAIN SWITCH
PROTECTIVE

TAPE

CENTER AIR VENT
PROTECTIVE
TAPEProCarManuals.com