1990 VOLKSWAGEN CORRADO steering wheel

J - PIN VOLTAGE CHARTSK - SENSOR RANGE CHARTSL - WIRING DIAGRAMSM - VACUUM DIAGRAMSMAINTENANCE INFORMATIONMAINTENANCE REMINDER LIGHT RESET PROCEDURESMETRIC CONVERSIONSMETRIC CONVERSIONSMIRRORS - POWERN - REMOVE/INSTALL/OVERHAULP - EGR FUNCTION TESTINGPOSSIBLE ENGINE STALL DUE TO FUEL RESTRICTIONPRE-ALIGNMENT CHECKSSCHEDULED SERVICESSERVICE INDICATOR & WARNING LIGHTSSTARTER - BOSCHSTEERING COLUMNSTEERING COLUMN SWITCHESSTEERING SYSTEM - POWERSUSPENSION - FRONTSUSPENSION - REARTRANSMISSION REMOVAL & INSTALLATION - A/TTRANSMISSION SERVICING - A/TTRANSMISSION SERVICING - M/TTROUBLE SHOOTING - BASIC PROCEDURESWAVEFORMS - INJECTOR PATTERN TUTORIALWHEEL ALIGNMENT SPECIFICATIONS & PROCEDURESWHEEL ALIGNMENT THEORY/OPERATIONWIPER/WASHER SYSTEMWIRING DIAGRAM SYMBOLSWIRING DIAGRAMS

* A/C-HEATER SYSTEM UNIFORM INSPECTION GUIDELINES *
Article Text (p. 2)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:27PM
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering and
suspension, wheel alignment, tires and wheels, driveline, engine
performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
* Example: An exhaust pipe has corroded severely and has a hole
in it through which exhaust gases are leaking. Replacement of
the exhaust pipe in this case is required due to functional
failure.
* Example: A brake rotor has been worn to the point where it
measures less than the vehicle manufacturer's specifications.
Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or to address a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may only
be to suggest service.
* Example: An exhaust pipe is rusted, corroded or weak, but no
leaks are present. In this case, the exhaust pipe has not
failed. However, there is evidence that the pipe may need
replacement in the near future. Replacement of the pipe may
be suggested for the customer's convenience in avoiding a
future problem.
* Example: The customer desires improved ride and/or handling,
but the vehicle's shocks or struts have not failed. In this
case, replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may

* ANTI-LOCK BRAKES UNIFORM INSPECTION GUIDELINE *
Article Text (p. 2)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:28PM
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering
and suspension, wheel alignment, tires and wheels, driveline,
engine performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.
Some conditions indicate that service or part replacement
is required because the part in question is no longer providing
the function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
* Example: An exhaust pipe has corroded severely and has a hole
in it through which exhaust gases are leaking. Replacement of
the exhaust pipe in this case is required due to functional
failure.
* Example: A brake rotor has been worn to the point where it
measures less than the vehicle manufacturer's specifications.
Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or to address a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may
only be to suggest service.
* Example: An exhaust pipe is rusted, corroded or weak, but no
leaks are present. In this case, the exhaust pipe has not
failed. However, there is evidence that the pipe may need
replacement in the near future. Replacement of the pipe may
be suggested for the customer's convenience in avoiding a
future problem.
* Example: The customer desires improved ride and/or handling,

* BRAKE SYSTEM UNIFORM INSPECTION GUIDELINES *
Article Text (p. 3)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:28PM
businesses working to improve the industry. Media sources also look to
MAP to provide information and advice to consumers and on working with
automotive technicians and repair establishments.
In the next few months, MAP plans to assist member repair
facilities in implementing the MAP Pledge to Customers, establishing
an alternate dispute resolution system to help resolve customer
complaints within the industry, and developing a shop accreditation
program to encourage policies in concert with the MAP Standards of
Service and Inspection Guidelines.
MAP has united the aftermarket behind its consumer-oriented
goals and has established itself both within and outside of the
industry. We welcome you to join us as MAP continues its outreach.
With your support, both the automotive repair industry and your
customers will reap the benefits. Please contact MAP at:
808 17th Street, NW Suite 200
Washington, D.C. 20006
Ph. (202) 466-7050 Fax (202) 223-9569
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering and
suspension, wheel alignment, tires and wheels, driveline, engine
performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
* Example: An exhaust pipe has corroded severely and has a hole
in it through which exhaust gases are leaking. Replacement of
the exhaust pipe in this case is required due to functional
failure.
* Example: A brake rotor has been worn to the point where it

* BRAKE SYSTEM UNIFORM INSPECTION GUIDELINES *
Article Text (p. 12)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:29PM
CAUTION: When installing calipers (loaded or unloaded), it is required
that friction material be matched in axle sets for consistent
braking characteristics.
Determine the need to replace or rebuild based upon the
individual caliper conditions that follow.
CALIPERSÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄCondition
³ Code ³ Procedure
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄBleeder port damaged
³ A ³ Require replacement of caliper.
(if non-repairable)
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄBleeder screw plugged
³ A ³ Require repair or replacement of

³ ³ bleeder screw. See note (1) below.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄBleeder screw broken off
³ A ³ Require replacement of caliper.
in caliper
³ ³ See note (1) below.
(if non-repairable)
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄBleeder screw seized
³ A ³ Require replacement of caliper.

³ ³ See note (2) below.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄCasting damaged - heavy
³ A ³ Require replacement of caliper.
corrosion affecting
³ ³ structural integrity
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄCasting damaged - worn by
³ A ³ Require replacement of caliper.
rotor or wheel, affecting
³ ³ structural integrity
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄDust boot around caliper
³ B,2 ³ Suggest rebuilding or replacement
is torn
³ ³ of caliper.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄLeaking
³ A ³ Require rebuilding or replacement

³ ³ of caliper.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting pin threads
³ A ³ Require repair or replacement of
damaged
³ ³ component with damaged threads.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting pin threads
³ A ³ Require repair or replacement of
stripped (threads missing)
³ ³ component with stripped threads.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting pin threads
³ A ³ Require repair or replacement of
stripped in caliper
³ ³ caliper bracket.
bracket (threads missing)
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting pin threads
³ A ³ Require repair or replacement of
stripped in steering
³ ³ steering knuckle.
knuckle (threads missing)
³ ³
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

* ELECTRICAL SYSTEM UNIFORM INSPECTION GUIDELINES *
Article Text (p. 3)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:29PM
estimate.
V. Work Authorization - No work will be performed without the
customer's prior approval.
VI. Limited Warranty - A minimum limited warranty will be
offered of 90 days or 4,000 miles, whichever comes first, covering
parts and labor.
VII. Returned Parts - All customers will be entitled to the
return of old parts, or if they choose, they may examine the parts
prior to leaving the store. Where failed parts are required to be
returned to the manufacturer in order to honor the warranty, the
customer will be allowed to examine the parts.
VIII. Classification of Parts - Replaced parts will be
identified as new, remanufactured, rebuilt or used. MAP participants
will inform the customer and indicate on the estimate and invoice
whether a part is new, remanufactured, rebuilt or used.
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering and
suspension, wheel alignment, tires and wheels, driveline, engine
performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.
Some conditions indicate that service or part replacement
is required because the part in question is no longer providing
the function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
* Example: An exhaust pipe has corroded severely and has a hole
in it through which exhaust gases are leaking. Replacement of
the exhaust pipe in this case is required due to functional
failure.

* ENGINE SYSTEMS UNIFORM INSPECTION GUIDELINES *
Article Text (p. 2)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:31PM
to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
concerned with auto repair and/or consumer protection are conducted.
Feedback from these representatives are brought back to members, and
the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers arbitration through MAP/BBB-CARE in cooperation with the
Council of Better Business Bureaus and individual participating
Bureaus. MAP "piloted" in Indianapolis and Pittsburgh during spring,
1996 - and publicized "roll-outs" in New Jersey, Detroit (MI), Chicago
(IL) and Richmond (VA) were conducted. To put some "teeth" in the
program, and accreditation requirement for shops was initiated. The
requirements are stringent and a self-policing method has been
incorporated which includes the "mystery shopping" of outlets. In
addition, a committee of service providers had been working diligently
developing standards for newspaper, television and Internet
advertising.
We welcome you to join us as we continue our outreach ...
with your support, both the automotive repair industry and your
customers will reap the benefits. Please visit MAP at our Internet
site: www.hunter.com/map.htm or contact us at:
808 17th Street, NW Suite 200
Washington, D.C. 20006
Ph. (202) 466-7050 Fax (202) 223-9569
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering and
suspension, wheel alignment, tires and wheels, driveline, engine
performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's

* EXHAUST SYSTEM UNIFORM INSPECTION GUIDELINES *
Article Text (p. 2)
1990 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Thursday, March 23, 2000 09:33PM
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
concerned with auto repair and/or consumer protection are conducted.
Feedback from these representatives are brought back to members, and
the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers arbitration through MAP/BBB-CARE in cooperation with the
Council of Better Business Bureaus and individual participating
Bureaus. MAP "piloted" in Indianapolis and Pittsburgh during spring,
1996 - and publicized "roll-outs" in New Jersey, Detroit (MI), Chicago
(IL) and Richmond (VA) were conducted. To put some "teeth" in the
program, and accreditation requirement for shops was initiated. The
requirements are stringent and a self-policing method has been
incorporated which includes the "mystery shopping" of outlets. In
addition, a committee of service providers had been working diligently
developing standards for newspaper, television and Internet
advertising.
We welcome you to join us as we continue our outreach ...
with your support, both the automotive repair industry and your
customers will reap the benefits. Please visit MAP at our Internet
site: www.hunter.com/map.htm or contact us at:
808 17th Street, NW Suite 200
Washington, D.C. 20006
Ph. (202) 466-7050 Fax (202) 223-9569
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, ABS, steering and
suspension, wheel alignment, tires and wheels, driveline, engine
performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.