1989 MAZDA 323 section E

--
ASSEMBLY B2
2311082-06
2311082.04
1
03UO62-09!
J 2311062-063
4. Hold the flywheel with the SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown.
Tightening torque:
96-l 03 N.m (9.6-10.5 m-kg, 71-76 ft-lb)
Clutch Disc and Clutch Cover (MTX)
1. Install the clutch disc and clutch cover using the SST or
equivalent. (Refer to Section H.)
Tightening torque:
16-26 N.m (1.8-2.7 m-kg, 13-20 ft-lb)
Drive Plate (ATX)
1. Remove the sealant from the drive plate holes in the crank-
shaft and from the drive plate lock bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the adapter, drive plate, and backing plate onto the
crankshaft.
3. Apply sealant to the drive plate bolts and install them.
4. Hold the drive plate with the
SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown.
Tightening torque:
96-103 N.m (9.8-10.5 m-kg, 71-76 ft-lb)
Timing Belt Pulley
1, Reverse the direction of the SST or equivalent on the
flywheel.
2311082.064
B2-77

62 INSTALLATION
03UOB2-12
. ,
03UOB2-12’
13UOB2-01.
Automatic transaxle
1. Join the engine and transaxle.
2. Install the transaxle mounting bolts shown in the figure.
3. Tighten the bolts.
Tightening torque
@I: 55-80 N-m (5.6-8.2 m-kg, 41-59 ft-lb)
@I: 37-52 Narn (3.8-5.3 m-kg, 27-38 ft-lb)
4. Align the torque converter bolts and drive plate holes.
5. Install the torque converter nuts and tighten them.
Tlghtening torque:
34-49 N,m (3.5-5.0 m-kg, 25-36 ft-lb)
No.2 engine mount rubber and bracket
1. Install the mount rubber and bracket.
Tightening torque:
37-52 N#m (3.8-5.3 m-kg, 27-38 ft-lb)
Throttle Cable (ATX)
1, Connect the throttle cable and adjust it.
(Refer to Section Kl.)
Starter
1, Install the starter to the transaxle housing.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
Intake manifold bracket
1. Install the intake manifold bracket.
Tightening torque
@: 19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
@I: 37-52 N.m (3.8-5.3 m-kg, 27-38 ft-lb)
B2-94

92 INSTALLATION
RESOiANCE CHAMBER
03UOBZ-154
Accelerator cable
1. Install the accelerator cable.
2. Adjust the cable deflection by turning nut A.
Deflection: 1-3mm (0.04-0.12 in)
Battery duct, battery carrier, and battery
1. Install the battery duct.
Tightening torque:
7.8-l 1 Nlm (80-l 10 cm-kg, 69-96 In-lb)
2. Install the battery carrier.
Tightening torque:
7.8-l 1 N*m (80-l 10 cm-kg, 69-96 in-lb)
3. Install the battery and the battery bracket.
Tightening torque:
2.9-5.9 N*m (30-60 cm-kg, 26-52 in-lb)
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 N#m (1.9-2.6 m-kg, 14-19 ft-lb)
@: 7.8-l 1 N*m (80-l 10 cm-kg, 69-95 In-lb)
2. Connect the air flow sensor connector.
Resonance chamber
I, Install the resonance chamber.
Tightening torque:
7.8-l 1 N#m (80-l 10 cm-kg, 69-95 In-lb)
Under cover and side cover
1. Install the under cover and side cover.
Steps After Installation
1. If the engine oil was drained, fill with the specified amount and type of engine oil.
(Refer to Section D.)
2. Fill the radiator with the specified amount and type of engine coolant.
(Refer to Section E.)
3. If the transaxle oil was drained, fill with the specified amount and type of transaxle oil.
(Refer to Sections J2, K.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage.
(2) ignition timing, idle speed. (Refer to page 82-8.)
(3) Operation of emission control system.
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
B2-102
2311082.047

INDEX D
/I? HYDRAULIC LASH ADJUSTER (HLA)
SERVICE, SECTION Bl
TION B‘
ENGINE &L SPECIFICATION
API SERVICE SG ECII ONLY
TOTAL CAPACITY
4.0 liters (4.2 US qt, 3.5 Imp qt)
I 23UODX-003
1. Oil pressure 4. Oil pan and main bearing support plate
Inspection.. ................................. page D- 6 (MBSP)
2. Engine oil Removal / Installation .................. page D- 9
Inspection page D- 7 5. Oil
................................... pump
Replacement .............................. page D- 7 Disassembly I Assembly.. ........... page D-l 3
LA-”
3. Oil filter Inspection.. ................................. page D-l 4
Replacement .............................. page D- 8
D-3

D INDEX
BP DOHC
HYDRAULIC LASH ADJUSTER (HLA)
SERVICE, SECTION B2
/
ICE,
ENGlNi OIL SPECIFICATION
API SERVICE SG EClI ONLY
TOTAL CAPACITY
4.0 liters (4.2 US qt, 3.5 Imp qt)
1. Oil pressure
Inspection ,,...,..,..,...........,.,,.,.,.,.. page D- 6
2. Engine oil
Inspection page D- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement ,.,... . . . . . . . . . ,.,....,..... . . page D-
7
3. Oil filter
Replacement . . . . . . . . . . . . . . . . .,.. , . . . . . . . . , page
D- 8 4. Oil pan and main bearing support plate
(MBSP)
Removal I inspection /
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page D- 9
5. Oil pump
Disassembly / Assembly... .I ,....... page D-l 3
Inspection ,.,,,.,....,..,,..,..,.,,.,..,..,., page D-l 4
6. Oil cooler
Removal I Installation . . . . . . . . . . . . . . . . . . page
D- 8
D-4

OUTLINE, TROUBLESHOOTING GUIDE D
OUTLINE
SPECIFICATIONS
Engine
Item
--
Lubrication system
Type
011 pump
Relief pressure kPa (kg/cm2, psi)
_~__
Type Oil filter
Relief pressure differential kPa (kg/cm2, psi)
Oil pressure switch activation pressure
kPa (kg/cm’, psi)
Total (dry engine)
liters (US qt, Imp qt)
Oil capacity Oil pan liters (US qt, Imp qt)
Oil filter liter (US qt, Imp qt)
Engine oil
Above -25OC (-13’F)
Viscosity number
Below 0% (32OF) BP SOHC BP DOHC
B6 SOHC
Force-fed type
Trochoid gear
343-441 (3.5-4.5, 50-64) m I, Full-flow, paper element
78-l 18 (0.8-l .2, 1 l-i 7)
25 (0.25, 3.6)
3.4 (3.6, 3.0) 4.0 (4.2, 3.5)
3.0 (3.2, 2.6) 3.6 (3.8, 3.2)
0.17 (0.18, 0.15)
API service SG Energy ConservingII (ECII) Only
SAE low-30
SAE 5W-30
23UODX-005
TROUBLESHOOTING GUIDE
Problem
Engine hard starting
Excessive oil
consumption
Oil pressure drop
Warming lamp
illuminates while
engine is running Possible Cause
Improper engine oil
Insufficient engine oil
Oil working up or down
011 leakage
Insufficient oil
Oil leakage
Worn and/or damaged oil pump gear
Worn plunger (inside oil pump) or weak spring
Clogged oil strainer
Excessive main bearing or connecting rod bearing
clearance
Oil pressure drop
Malfunction of oil pressure switch
Malfunction of electrical system Remedy
Replace
Add oil
Refer to Section B
Repair
Add oil
Repair
Replace
Replace
Clean
Refer to Section B
As described above
Refer to Section T
Refer to Section T Page
D- 7
D- 7
-
D- 7
-
D-13, 14
D-13, 14
-
-
23UODX-015
D-5

WATER PUMP WATER PUMP
E
REMOVAL / INSTALLATION
Caution
l Do not disassemble the water pump. If a problem is found, replace the pump as a Unit.
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal.
B6 SOHC AND BP SOHC
83, t B6, BP SOHC
I
I
L-----------------_-- ------- -1
/ \/
19-26 (1.9-2.6, 14-19) LVVVLI. YY,
1. Timing belt 4. Water pump assembly
Service ., . . .., ,, ., . . . . . ,. ,.,. ., ,., . . ,,.... . . . . , Section Bl Inspect for cracks, damaged mounting
2. Water inlet pipe
and gasket surface, bearing condition, and leakage
3. Water bypass pipe and O-ring 5. Water pump gasket
E-l 1

BP DOHC
L 7.8-11 N-m (60-110 cm-kg, 69-95 in-lb)
E WATER PUMP
157-167
I
(W-17, 116-123) I
I
/
I
I
I
---N-w------
---------------
----_---_
-I
N.m (m-kg, ft-lb) 1
^^, *--., ^^^
1. Timing belt
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 5. Water pump assembly
B2
2. Water inlet pipe and gasket Inspect for cracks, damaged mounting
3. Water bypass pipe and O-ring surface, bearing condition, and leakage
4. Oil dip stick pipe bracket 6. Water pump gasket
Steps After Installation
1. Fill the radiator with the specified amount and type of engine coolant. (Refer to page E-6.)
2. Connect the negative battery cable,
3. Start the engine and check for leaks.
03UOEX-018
E-12